• 한국결정성장학회지
• /
• 제1권1호
• /
• pp.1-4
• /
• 1991

The applicability of $LiNbO_{3}$ as a substrate for fabrication of Ti-indiffused waveguide electro-optic devices is limited. Ti diffuses comparatively in congruently melting $LiNbO_{3}$; the Curie temperature of this material is too low to permit diffusion temperatures much above $1100^{\circ}C$ without the necessity of re-poling the crystal. Both of hese difficulties could be eliminated by incorporating certain dopants in $LiNbO_{3}$. Crystals of $LiNbO_{3}$ doped with Ti and Mg were grown and evaluated. The electroptic coefficients and birefringence of $LiNbO_{3}$ doped crystals were measured at ${\lambda}=.6328$ and $1.32\;$\mu{m}$. Curie temperatures were measured. The Curie temperature of both undoped and Ti-doped $LiNbO_{3}$ was $1130^{\circ}C$; that for Mg-doped $LiNbO_{3}$ was $30^{\circ}$ higher. From these data, a composition for the crystals was estimated. Thermogravimetric data confirmed this estimate and showed that the composition of Mg : $LiNbO_{3}$ was $49.3{\pm}0.2mole%\;Li_{2}O$ ; the composition of the undoped and Ti : $LiNbO_{3}$ samples was $48.6{\pm}0.2mole%$. Diffusion of Ti into both Mg-doped and Ti-doped $LiNbO_{3}$ crystals was studied as a function of $Li/NbO_{3}$ ratio and temperature.

• Journal of Magnetics
• /
• 제10권1호
• /
• pp.28-32
• /
• 2005

The magnetic properties and ordering behavior of Nb-doped FePt alloy films prepared by dc-magnetron sputtering were investigated. It was found that Nb addition retarded the ordering reaction from the disordered face-centered-cubic (fcc) Al phase to the ordered face-centered-tetragonal (fct) L1₀ phase. The tetragonality (c/a ratio) of the ordered fct L1₀ phase increased with the Nb concentration. Nb addition hampered c-axis contraction during ordering, probably because the larger Nb atoms occupy Pt sites. Consequently, the coercivity and magnetocrystalline anisotropic energy of Nb-doped FePt alloy films are lower than those of un-doped FePt film under equivalent annealing conditions.

• 한국재료학회지
• /
• 제8권11호
• /
• pp.1031-1037
• /
• 1998

Zircaloy-4와 Zr-2.5Nb 합금의 부식에 미치는 냉각속도와 소둔온도의영향을 조사하기 위해서 여러 가지 방법으로 열처리된 시편에 대해서 autoclave 부식시험을 실시하였다. 냉각속도의 영향을 조사하기 위해서 시편을 $1050^{\circ}C$에서 30분 가열 후 염빙수냉, 수냉, 유냉, 공냉, 노냉의 방법에 의해 열처리하였으며, 소둔온도의 영향을 조사하기 위해서 $\alpha$온도, $\alpha$+$\beta$온도, $\beta$온도구역에서 열처리하였다. $500^{\circ}C$부식시험 결과, Zircaloy-4합금에서는 nodule형 부식이 발생되는 반면에 Zr-2.5Nb 합금에서는 nodule형 부식이 발생되지 않았다. Zirfcaloy-4 합금에서는 nodule형 부식이 발생되는 반면에 Zr-2.5Nb 합금에서는 nodule형 부식이 발생되지 않았다. Zircaloy-4합금은 냉각속도가 빠를수록 내식성이 증가하는 반면에 Zr-2.5Nb합금은 냉각속도가 빠를수록 내식성이 감소하는 경향을 보였다. 또한 소둔온도가 증가할수록 Zr-2.5Nb 합금의 내식성은 감소하는 결과를 보였다. Zircaloy-4의 내식성은 Fe, Cr 원소의 기지내 분포와 석출물의 분포에 의해 지배를 받으며 Zr-2.5Nb 합금의 내식성은 기지조직내의 Nb 농도와 $\beta_{-Nb}$상에 의해 지배를 받는 것으로 사료된다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.962-963
• /
• 2006

The precipitation behaviors of ${\gamma}"(Ni_3Nb)$ in four Ni-base alloys were investigated. The four alloys were forged Ni20Cr20Fe5Nb alloy, mechanically alloyed Ni20Cr20Fe5Nb alloy, IN 718 alloy and ECAPed(equal channel angular pressing) IN 718 alloy. Aging treatment was employed at either $600^{\circ}C$ or $720^{\circ}C$ for 20 hrs. The TEM observation and hardness test were performed to identify the formation of ${\gamma}"$. The precipitation of ${\gamma}"$ was noticed after aging at $600^{\circ}C$ for 20 hrs in the mechanically alloyed Ni20Cr20Fe5Nb alloy and ECAPed IN 718 alloy, while it was observed after aging at $720^{\circ}C$ for 20 hrs in the forged Ni20Cr20Fe5Nb alloy and IN 718 alloy before ECAP. The lower aging temperature for ${\gamma}"$ precipitation in the mechanically alloyed Ni20Cr20Fe5Nb alloy and ECAPed IN 718 alloy than in the forged Ni20Cr20Fe5Nb alloy and IN 718 alloy before ECAP appeared to be due to the severe plastic deformation which occurred during mechanical alloying or ECAP.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.496-499
• /
• 2000

In order to investigate the effect of Ge addition to the Cu Matrix on the microstructure and the critical current density, four kinds of internal tin processed Nb$_3$Sn strands with pure Cu and Cu 0.2, 0.4, 0.6 wt％ Ge alloy were drawn to 0.8 mm diameter. The microstructure and critical current of internal tin processed Nb$_3$Sn wires that were heat treated at temperatures ranging from 68$0^{\circ}C$ to 74$0^{\circ}C$ for 240 h were investigated. The Ge addition to the matrix did not make workability worse. A Ge rich layer in the Cu-Ge matrix suppressed the growth of the Nb$_3$Sn layer and promoted grain coarsening. The greater the Ge content in the matrix, the lower the net Jc result after Nb$_3$Sn reaction heat treatment. There was no significant variation in Jc observed with heat treatment temperature ranging from 68$0^{\circ}C$ to 74$0^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.268-269
• /
• 2007

In this study, the structural and microwave dielectric properties of the $Sr_5Nb_4O_{15}$ cation-deficient perovskite ceramics with sintering temperature were investigated. All sample of the $Sr_5Nb_4O_{15}$ ceramics were prepared by the conventional mixed oxide method and sintered at $1350^{\circ}C{\sim}1500^{\circ}C$. The bulk density, dielectric constant and quality factor of the $Sr_5Nb_4O_{15}$ ceramics were increased with increasing sintering temperature. In the case of the $Sr_5Nb_4O_{15}$ ceramics sintered at $1500^{\circ}C$ for 5h, the dielectric constant, quality factor and temperature coefficient of the resonant frequency (TCRF) were 22.35, 16,577GHz, +13.40ppm/$^{\circ}C$, respectively.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2002년도 학술대회 논문집
• /
• pp.123-126
• /
• 2002

Samples of Nb/Al-Al$O_{x}$/Nb tunnel junction with the size of 50$\mu$m $\times$ 50$\mu$m were fabricated by employing self-aligning and reactive ion etching technique. In the samples with high-quality, $V_{m}$ value (the product of the critical current and subgap resistance measured at 2 mV) was 34 mV at the critical current density $J_{c}$ = 500 A/$cm^{2}$ and $V_{g}$ value (the gap voltage) was 2.8 mV. In the higher $J_{c}$, voltage fluctuation in the current rising at the gap voltage was observed. The $V_{m}$ and $J_{c}$ value were 8 mV and 900 A/$cm^{2}$, respectively.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.107-108
• /
• 2006

The effect of WC or NbC addition on various properties of Ti(C0.7N0.3)-Ni cermets was investigated. The microstructure oj Ti(C0.7N0.3)-xWC-20Ni showed a typical core/rim structure, irrespective of the WC content, whereas the structure oj Ti(C0.7N0.3)-xNbC-20Ni was different and was dependent on the NbC content. The hardness (HV) and the fracture toughness (KIC) had a tendency to increase marginally, while the coercive force (HC) and the magnetic saturation $(4{\pi}{\sigma})$ decreased gradually with an increase in WC or NbC content in the systems studied. In addition, increasing WC content in Ti(C0.7N0.3)-xWC-20Ni system, decarburization was retarded, while denitrification was accelerated

• 한국초전도ㆍ저온공학회논문지
• /
• 제2권2호
• /
• pp.1-5
• /
• 2000

There is the possibility that internal tin processed Nb$_3Sn$ wires are locally heated during the drawing process and the jacketing process. It is important to know the variations in J$_c$ of internal tin processed Nb$_3Sn$ wires caused by local heating. Internal tin processed Nb$_3Sn$ rods were cold worked to 2.28 mm, using the appropriate reduction ratio, and then cut into several pieces. At this stage, wires were locally 50 mm heat zone heated up to 360$^{\circ}C$. The locally heated Nb$_3Sn$ wires were drawn to a final diameter size of 0.81 mm. Others were cold worked successively to 0.81 mm and locally heated with the same conditions. 2 types of locally heat treated wires were wound on Ti-6Al-4V barrels and heat treated for the Nb$_3Sn$ reaction. Local heating of internal tin processed Nb$_3Sn$ wires after the J$_c$ of these wires. However, local heating at an intermediate stage of the drawing process caused a decrease in J$_c$. When the local heating temperatures were higher than melting point of Sn, non-Cu J$_c$'s decreased significantly. A Sn-Cu alloyed boundary appeared after local heating over the melting point of Sn, and caused work hardening and a decrease in the workability.

• E2M - 전기 전자와 첨단 소재
• /
• 제3권3호
• /
• pp.233-241
• /
• 1990

본 연구에서는 xPb(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-yBa(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-zPbTiO(0.50.leq.x.leq.0.60, 0.10.leq.y.leq.0.20, 0.20.leq.z.leq.0.40)세라믹을 1050.deg.C에서 2시간동안 유지시켜 일반소성법으로 제작하였다. 시편 제작시 조성은 조성변태 상경계부근을 선택하였으며 Ba(Zn$_{1}$3/ Nb$_{2}$3/)O$_{3}$ 고용량에 따른 purochlore상의 억제 및 그 영향을 조사하고 구조적, 유전적 및 압전적 특성을 측정하였다. X-선 회절분석 및 미세구조의 관찰 결과, Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량에 따라 pyrochlore상 및 미반응 물질등은 억제되어 0.20mol 고용된 시편에서는 균질한 perovskite상이 형성되었다. Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량이 증가함에 따라 유전상수는 증가하여 0.50PZN-0.20BZN-0.30PT시편의 경우 6880.9의 높은 값을 나타내었으며 정전용량의 온도계수는 감소하여 0.383[%/.deg.C]의 양호한 값을 나타내었다. 큐리온도는 PbTiO$_{3}$의 고용량이 0.20mol에서 0.40mol로 증가함에 따라 30.deg.C에서 170.deg.C로 증가하였다. 전기기계 결합계수 (K$_{p}$), 기계적 품질계수(Qm) 및 압전전하 계수 (d$_{33}$)는 조성변태 상경계 부근의 조성에서 크게 나타났으며 0.60PZN-0.15BZN-0.25PT 시편의 경우 각각 58.5%, 120.5, 150x$10^{-12}$[C/N]의 값을 나타내었다.다.다.