• 한국세라믹학회지
• /
• 제33권1호
• /
• pp.17-24
• /
• 1996

Pb(Mg1/3Nb2/3)O3 powder with high purity chemical homogeniety and reactivity was prepared by solvent eva-poration of common solution. The common solution was fabricated using a Pb(NO3)2 Mg(NO)3 and NB solution which was prepared by dissolving NbC in H2O2 acquous solution. In precusor powder prepared by solvent evaporation method the synthetic temperature of Pb(Mg1/3 Nb2/3)O3 phase was lowered. And the formation of homogeneous Pb(Mg1/3Nb2/3)O3 phase was enhanced but the formation of pyrochlore phase was reduced. The dielectric constant of PMN ceramics from the synthesized powder was found to increase with both sintering temperature and excess MgO and subsequent analysis of the microstructures confirmed that this was due to an increase in grain size. The grain size dependence is explained as a consequence of low-permittivity grain boundaries.

• 한국세라믹학회지
• /
• 제27권6호
• /
• pp.713-720
• /
• 1990

The effects of substituting Zn+2 for Ni+2 ion on dielectric and piezoelectric prooperties of Pb(Zn1/3Nb2/3)O3-Pb(Ni1/3Nb2/3)O3-PZT ceramics were investigated. With increasing Zn2+ contents the tetragonality was appreciably enhanced and the grain size decreased. Both Curie temperature and thermal stability were increased with increase in Zn2+ contents since the Zn+2 partial substition for Ni+2 could form solid solution in almost range of the composition investigated. Piezoelectric prooperties showed the maximum($\varepsilon$ T/$\varepsilon$0=5014, kp=0.56, d31=250$\times$10-12m/V) in 4.5Pb(Zn1//3Nb2/3)O3-40.5Pb(Ni1/3Nb2/3)O3-55PZT composition sintered at 125$0^{\circ}C$ and then decreased again due to the phase boundary movement for tetragonal phase of the solid solution of Zn2+ amount.

• 한국전기전자재료학회논문지
• /
• 제25권11호
• /
• pp.867-872
• /
• 2012

In this study, in order to develop excellent lead free piezoelectric ceramics for piezoelectric actuators application, $Li_{0.04}(Na_{0.50}K_{0.50})_{0.96}[(Nb_{0.86}Ta_{0.10}Sb_{0.04})_{0.994}Co_{0.015}]O_3+0.0025SrO+0.15\;wt%K_2CO_3+x\;wt%Nb_2O_5$ (x = 0 - 0.5 wt%) (abbreviated as LNKNTSCS-xN) ceramics were fabricated by a conventional sintering technique. the phase structure, microstructure and electrical properties were investigated with a emphasis on the influence of the $Nb_2O_5$ content. High electrical properties of $d_{33}$=234 pC/N, kp=0.392, ${\varepsilon}_r$=1,395, ${\rho}=4.70g/cm^3$ were obtained from the specimen with x=0.4 wt%, which suggests that the composition ceramics is a promising lead-free piezoelectric material.

• 한국재료학회지
• /
• 제8권4호
• /
• pp.304-311
• /
• 1998

0.07%C-0.014%Ti-0.015Nb-0.005%B강 (강종 B)을 각각 TMCP처리하여 그 기계적 특성과 B의 거동을 조사하였다. Ta-B강이 Ti-Nb-B강보다 인장강도는 더 우수하였으나 충격 흡수에너지는 훨씬 더 낮았다. Ta-B강의 강도가 Ti-Nb-B강보다 더 우수한 이유는 Ta-B강에서의 Ta의 석출강화 효과가 Ti-Nb-B강에서의 Ti와 Nb의 석출강화 효과보다 더 크기 때문으로 생각된다. Ta-B강은 입내파괴, Ti-Nb-B강은 임계파괴의 파괴양상을 보여이며, Ti-Nb-B강이 Ta-B 강보다 더 큰 충격 흡수에너지를 나타내었다. TMCP에서는 항온변태시의 평형석출과는 달리 연속냉각방법을 사용하였기 때문에 B가 결정립계에 평형적 또는 비평형적으로 편석되어 준안정상으로 생각되는 연속적인 필름 형태의 붕화물을 형성한다. 또한, 냉각속도의 차이에 따라 석출물은 결정질이 되거자 비정질이 되었다. B의 함량이 많은 Ti-Nb-B강에서는 석출물이 비정질상이었다. 한편, B함량이 적은 Ta-B강에서는 B강에서는 결정립계에서 B가 관찰되지 않아는데, 이것은 결정립계에서의 B의 석출이 B의 함량에 매우 민감함을 의미하는 것이다.

• 한국주조공학회지
• /
• 제24권4호
• /
• pp.231-237
• /
• 2004

Bake hardenable steel utilizes the phenomenon of strain aging to provide an increase in the yield strength of formed components. An increase of the carbon content will improve the bake hardening response: more solutes are available to pin mobile dislocations and to form the clusters more rapidly. But aging resistance decrease as increasing solute carbon. In order to under-stand the compatibility between bake hardenability and aging resistance. The optimum solute carbon control methods during manufacture should be determined. In this paper, the effect of continuous heat cycle conditions such as soaking temperature, rapid cooling start temperature, cooling rate on BH(Bake Hardenability), AI(Aging Index), YP-El(Yield Point Elongation) and other mechanical properties have been investigated. and following results were obtained. In the case of soaking temperature, BH increases with higher soaking temperature because of NbC $dissolution(830^{\circ}C)$, Therefore the solute carbon and BH at $850^{\circ}C$ and $870^{\circ}C$ are higher than these at $810^{\circ}C$. But BH at $870^{\circ}C$ is a little lower than that at $850^{\circ}C$ owing to the ferrite grain size. The measurement of amount of dissolution C using IFT(Internal Friction Test) can explain the relation of solute carbon and BH.

• 비파괴검사학회지
• /
• 제22권2호
• /
• pp.140-148
• /
• 2002

중수로 압력관으로 사용되는 Zr-2.5Nb 재료의 고온 이방성 탄성계수를 고온 초음파공명분광법(RUS)로 측정하였다. 소형 가열로 내에 알루미나 waveguide와 광대역 초음파 센서를 사용하여 초음파에너지를 시편에 가하고 시편의 공명주파수를 측정하였다. 압력관의 축 방향, 반경 방향, 원주 방향에 일치하도록 장방형 시편을 가공하였으며 각 방향에 대한 탄성계수 텐서 9개의 값을 상온${\sim}500^{\circ}C$ 온도 구간에서 측정하였다. 탄생계수 텐서, $c_{ij}$는 모두 온도가 증가함에 따라 점진적으로 감소하며 원주 방향의 탄성계수가 축 방향 및 반경 방향의 탄성계수보다 높았다. 이것은 Young's modulus나 shear modulus의 경우에도 일치하였으며 축 방향과 반경 방향의 경우 큰 차이를 나타내지 않았다. 축 방향 및 반경 방향의 비틀림 탄생계수가 $150^{\circ}C$ 부근에서 서로 교차하였으며 이는 단결정 지르코늄의 $c_{44}$ 및 $c_{66}$의 교차 현상과 일치하였다.

• 한국분말재료학회지
• /
• 제15권6호
• /
• pp.482-488
• /
• 2008

The indentation technique has been one of the most commonly used techniques for the measurement of the mechanical properties of materials due to its experimental ease and speed. Recently, the scope of indentation has been enlarged down to the nanometer range through the development of instrumentations capable of continuously measuring load and displacement. In addition to testing hardness, the elastic modulus of submicron area could be measured from an indentation load-displacement (P-h) curve. In this study, the hardness values of the constituent phases in Ti($C_{0.7}N_{0.3}$)-NbC-Ni cermets were evaluated by nanoindentation. SEM observation of the indented surface was indispensable in order to separate the hardness of each constituent phase since the Ti($C_{0.7}N_{0.3}$)-based cermets have relatively inhomogeneous microstructure. The measured values of hardness using nanoindentation were ${\sim}20$ GPa for hard phase and ${\sim}10$ GPa for binder phase. The effect of NbC addition on hardness was not obvious in this work.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.519-523
• /
• 1995

The Fe-TM-C-N nanocrystalline films (TM : Hf, Zr and Nb) are investigated to examine the relation between microstructure and soft magnetic properties. In these films, as the atomic radius of TM element increases, $P_{N2}$ which was added to get good soft magnetic properties was decreased and the maximum value of the permeability shifted to the high Fe range in the composition diagram. The best soft magnetic properties achieved in these films are : Hc of 0.15 Oe, $\mu_{eff}$ of 7800 (1MHz) and $4{\pi}M_{s}$ of 17.5 kG in Fe-Hf-C-N film ; Hc of 0.06 Oe, $\mu_{eff}$ of 2750 (1MHz) and $4{\pi}M_{s}$ of 16.8 kG in Fe-Zr-C-N film and Hc of 0.31 Oe; $\mu_{eff}$ of 2100 (1MHz) and $4{\pi}M_{s}$ of 15.5 kG in Fe-Nb-C-N film. It was considered that the stronger the bonding force between TM and C(N), the finer TM(C,N) phase is precipitated and therefore, the finer $\alpha$-Fe grains are formed. The effective permeability of the Fe-Zr-C-N films and Fe-Nb-C-N films remains nearly constant up to 10 MHz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1250-1251
• /
• 2008

In this study, the dielectric ceramics with low loss were investigated for high frequency application. All sample of the $Ba_5M_4O_{15}$ (M=Ta, Nb) ceramics were prepared by the conventional mixed oxide method and sintered at $1325{\sim}1575^{\circ}C$. The bulk density and dielectric constant of the $Ba_5Ta_4O_{15}$ ceramics were increased continuously with increasing of sintering temperature. The quality factor was increased in the sintering temperature of $1375{\sim}1475^{\circ}C$ but decreased at the temperature above 1475$^{\circ}C$. In the case of $Ba_5Nb_4O_{15}$ ceramics, the bulk density, dielectric constant and quality factor were increased with sintering temperature but decreased above temperature of 1400$^{\circ}C$. The dielectric constant, quality factor and temperature coefficient of the resonant frequency (TCRF) of the $Ba_5Ta_4O_{15}$ and $Ba_5Nb_4O_{15}$ ceramics, sintered at 1475$^{\circ}C$ and 1400$^{\circ}C$, were 25.15, 53105 GHz, -3.06 ppm/$^{\circ}C$ and 39.55, 28052 GHz, 5.7 ppm/$^{\circ}C$, respectively.

• 열처리공학회지
• /
• 제16권1호
• /
• pp.10-15
• /
• 2003

In Nb, V and Ti added steels, carbo-nitrides are formed due to their strong interaction with C and N. The formation of carbo-nitrides has an important role to control the microstructure as well as mechanical properties by grain size refinement and precipitation hardening. However, the quantitative analysis of distribution of precipitates and the effect of precipitates on the phase transformation and mechanical properties are still far from satisfactory. In this study, the quantitative analysis of precipitates in austenite was investigated using the fact that the formation of precipitates in Nb, V and Ti added steels accelerates austenite/ferrite transformation. The formation of precipitates was controlled by adjusting holding temperature and time in austenite region, transformed Volume fractions were measured by dilatometer during slow cooling, Iso-precipitation kinetics were determined by comparing 5% and 50% volumes transformed at various conditions respectively. The result was compared with the calculated.