• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.3
• /
• pp.296-303
• /
• 2014

This paper describes the simplified simulation method of the wire-guided underwater test body with natural supercavitation. In this paper, the simulation based model of the wire-guided underwater body with natural supercavitation is proposed by using preceding research and commercial flow-analysis software. By using the model, the 1-dimensional wire-guided body motion in natural supercavitation can be solved very fast with reliability. The suggested model is validated by the comparison of simulation results with experimental data.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.1
• /
• pp.24-31
• /
• 2021

In this study, we present experimental observations of artificial supercavitation generated by the injection of compressed air at multiple locations on the body. Experiments were conducted at a cavitation tunnel equipped with a special facility to remove injected air before returning to the test section. Artificial supercavitation, which is generated at a relatively low speed compared to natural supercavitation, is formed asymmetrically on the axis of the body due to the buoyancy effect. In order to accelerate the development of the supercavity and increase the area covering the body, an experimental device capable of additional injection from the body was designed and its performance was evaluated through the model test. The shapes of the supercavity generated by multi-injections of different combinations according to different flow speeds were analyzed using high-speed shadow images. The results show that multiple injections at suitable locations can effectively increase the length of the supercavity and consequently improve propulsion efficiency.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.6
• /
• pp.465-472
• /
• 2016

A study was carried out to investigate typical features of natural supercavitation generated behind axisymmetric bodies such as disk and cone shaped cavitators. Main focuses of the study were to observe formation process of the supercavity and to measure drag forces acting on cavitators. Experiments were carried out at the cavitation tunnel of the Chungnam National University (CNU-CT), which has a capability to make sufficient flow speed for supercavitation experiments and to remove broken cavity bubbles coming back to the test section. Blockage effects on supercavity dimensions were evaluated and an effort was made to correlate tunnel experiments with unbounded flow. On the basis of experimental and numerical results, geometrical features of supercavities and characteristics of drag forces were examined and their relations were proposed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.3
• /
• pp.300-308
• /
• 2015

Recently supercavitating underwater torpedo moving at high speed (over 200 knots) has been interested for their practical advantage of the dramatic drag reduction. Cavitator located in front of the torpedo plays an important role to generate a natural supercavity and control the motion of the object. Supercavity can be created artificially by injection of compressed gas from the rear of the cavitator at a relatively low speed. In this paper, we investigated physical characteristics of artificial supercavities through cavitation tunnel experiments. One of the main focuses of the study was to measure pressure inside the cavity, and examined variation of the gravity effects appearing according to different amount of injected air. It was also found that a stable supercavity could be sustained at injection rates less than that required to form the stable supercavity because of hysteresis effect.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.4
• /
• pp.327-334
• /
• 2019

Recently, there has been a growing interest in artificial supercavitation as a way to reduce friction drag of submerged vehicles. A cavitator plays an important role to generate the supercavity, so many studies have focused on the case of cavitator only. However, the body shape behind the cavitator affects the growth of the supercavity and this effect must be considered for evaluating the overall performance of the system. In this work, we conducted experimental investigation on artificial supercavitation generated by different combinations of the cavitator and body. We observed the supercavity pattern by using a high-speed camera and measured the pressure inside the cavity by using an absolute pressure transducer. We estimated the relation between the amount of injected air and the supercavity shape for different combinations. In summary, the disk type cavitator generates larger supercavity than that of the cone and ellipsoidal cavitators, but cavity development speed is relatively slower rather than the others. Furthermore, fore body angle plays an important role to generate the supercavity enveloping the entire body.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.3
• /
• pp.236-247
• /
• 2015

In this paper, the experimental equipments for ventilated supercavitation in cavitation tunnel is constructed and the basic data of ventilated supercavitation regard to the entrainment coefficient and Froude number is fulfilled. The experiments are conducted for the disk cavitator with injecting air and the pressure inside cavity and the shape of cavity are measured. As the entrainment coefficient increases while the Froude number is kept constant, the ventilated cavitation number decreases to a minimum value which decreases no more even with increasing the air entrainment. The minimum value of ventilated cavitation number, caused by the blockage effect, decreases according to increasing the diameter ratio of test section to cavitator. The cavity length is rapidly enlarged near the minimum cavitation number. In low Froude numbers, the cavity tail is floating up due to buoyancy and the air inside the cavity is evacuated from its rear end with twin-vortex hollow tubes. However, in high Froude numbers, the buoyancy effect is almost negligible and there is no more twin-vortex tubes so that the cavity shape becomes close to axisymmetric. In order to measure the cavity length and width, the two methods, which are to be based on the cavity shapes and the maximum width of cavity, are applied. As the entrainment coefficient increases after the ventilated cavitation number gets down to the minimum cavitation number, the cavity length still increases gradually. These phenomenon can be confirmed by the measurement using the method based on the cavity shapes. On the other hand, when the method based on the maximum width of cavity is used, the length and width of the cavity agree well with a semi-empirical formular of natural cavity. So the method based on the maximum width of cavity can be a valid method for cavitator design.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.131-136
• /
• 2017

High speed under water vehicle by using solid rocket motor, which is a natural cavitation type, was tested. The vehicle's speed and running distance was measured, and pressure sensors installed on the surface of the vehicle show pressure-time history of pressures according to the development of the supercavitation. Underwater cameras installed on the wall of the test pool recorded whole processes from the onset of the supercavitation to fully developed one. CNU-SuperCT based on 2-dimensional inviscid theoretical analysis was used to simulate the test result. In consideration of CNU-SuperCT does not include the control fins of the vehicle, simulation results agree with test results very well. Also, pictures from underwater cameras support the test results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.4
• /
• pp.12-17
• /
• 2018

A natural cavitation-type high-speed underwater vehicle with solid rocket motor is tested, and its speed and running distance are measured. The outputs from pressure sensors on the surface of the vehicle reveal a pressure-time history reflecting the development of supercavitation. Underwater cameras installed on the wall of the test pool record the entire process from the onset of supercavitation to its full development. CNU-SuperCT, based on two-dimensional inviscid theoretical analysis, is used to simulate test results. Considering CNU-SuperCT does not include the control fins of the vehicle, simulation results agree with test results very well. Additionally, pictures from underwater cameras support the test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.1
• /
• pp.75-82
• /
• 2018

Wedge-shaped fins are generally used to provide sufficient forces and moments to control and maneuver a supercavitating vehicle. There are four fins placed along the girth of the vehicle, near he tail: two of the fins are horizontal and the other two fins are vertical. In a fully developed supercavitating flow condition, a part of the fin is in a cavity pocket and the other is exposed to water. In this paper, experimental investigations of hydrodynamic characteristics of the wedge-shaped fin models are presented. Experiments were conducted at a cavitation tunnel of the Chungnam National University. We first closely observed the typical formation of wake cavitation and measured lift and drag forces acting on two different test models. Next, using a special device for generating natural and artificial supercavities, we investigated hydrodynamic forces at different cavitation number conditions. This work provides a basis for interpreting the cavity stability and hydrodynamic characteristics of the wedge-shaped control fin for a supercavitating vehicle.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.58-64
• /
• 2011

The objective of this paper is to investigate the gravity effect on the shape characters of natural supercavity. A finite difference solver along with an implicit, dual time, preconditioned, three-dimensional algorithm has been used to solve the two-phase Navier Stokes equations. Numerical solutions were performed for natural supercavitating flow past a disk for different cavitation and Froud numbers. The numerical results were compared with corresponding analytical results in quantitative manner and it was found that the shape of supercavity was reasonably predicted Numerical results indicated that the gravity effect can induce the asymmetry of supercavity. The asymmetry was apparent when the froud number was smaller so that for constant cavitation number when we reduced the froud number the opt of the axis of supercavity increased. Moreover, for specific froud number a decrease in cavitation number resulted in an increase in the offset of the supercavity Numerical results revealed that for froud number greater than 25 the gravity effect is negligible.