• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.260-265
• /
• 1996

Active control of forced vibration response of a fixed-fixed beam implementing PZT sensor/actuator was conducted. Among various control scheme, PPF control was chosen due to its amenability and natural robustness. For a single frequency excitation, the PPF control provided reasonable controllability with the appropriate damping ratio of the compensator. Without increasing actuator voltage, best controllability can be obtained by the exact tuning between the natural frequency of the structure and the cut-off frequency of the compensator. Even the multi-frequency excitation, the PPF provided good vibration suppression for corresponding mode of interest, even though residual modes should be controlled with independent compensators for each mode.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.326-332
• /
• 1995

Using natural frequency measurement method, which is one of NDT method, natural frequency of the hot-rolled mild steel plate(specimen) under fatigue loading was measured. Between the degradation of the specimen under fatigue loading and the variation of the natural frequency of the specimen was investigated. As a result, the degradation of the specimen was described and monitored as variation of natural frequency of specimen. The natural frequency of specimen decreased gradually under fatigue loading. This means the variation of material properties of specimen. Especially. It means the variation of Young's modulus of specimen.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.63-70
• /
• 2008

Conical horn is used in many high frequency ultrasonic horns, to achieve a longitudinal vibration mode across a wide ultrasonic tool horn output surface. Modal analysis is method for designing tuned ultrasonic tool horn and for the prediction natural frequency of ultrasonic tool horn vibration mode. The design of ultrasonic horn is based on prototype estimate obtained by FEM analysis. The FEM simulated ultrasonic tool horn is built and characterized experimentally through laser vibrometer and electrical impedance analysis. In this paper, FEM analysis is developed to predict the natural frequency of ultrasonic tool horn and use of in the optimal design of ultrasonic horn shape.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.424-431
• /
• 2003

The spacer grid is one of the main structural components in the fuel assembly, which supports the fuel rods and maintains coolable geometry from an external load. A vibration test and a finite element analysis using ABAQUS on a dummy fuel rod continuously supported by Optimized H type(OHT) and New Doublet (ND) spacer grids arc performed to obtain the vibration characteristics such as natural frequencies and mode shapes an(1 to verify a finite element model. The results from the test and the finite element analysis are compared by modal assurance criteria (MAC) values. It is resulted that MACs for the first, the third and the fifth mode shapes are relatively good as compared with those of the second an(1 fourth ones. The natural frequency differences between two methods as well as the mode comparison results for the rod with OHT spacer grid are better than those with ND spacer grid. It is judged that the FE model for the ND spacer grid spring should be modified to consider the long contact length which actually happen when the spring supports the rod.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.5
• /
• pp.30-37
• /
• 2015

The estimation of system damping parameter of the response signal with lower natural frequency and higher damping parameter from free vibration is affected by the wavelet center frequency. This study discusses these considerations in the context of the wavelet's multi-resolution character and includes guidelines for selection of wavelet center frequency. The experiment with H-Beam and numerical examples with respect to three cases (i)single mode, (ii)separated modes and (iii)close modes demonstrate the validity of method to improve the accuracy of the estimated damping parameter. The localization of the corresponding scale for the total scales is determined by the natural frequency of the analysing mode and is affected by the wavelet center frequency. Thus, the reliability for the accuracy of the estimated damping parameter can be improved by the corresponding scale of the natural frequency for the analysing mode is localized at the half of the total scales.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.148-156
• /
• 2001

Brake judder, one of low Sequency vibrations in brake system is determined by the excitation of Brake Torque Variation (BTV). The largest contributor to BTV is disc thickness variation. In this study, the static loads of brake torque at Suspension Mounting Points (SW) are obtained by the quasi-static analysis using DADS. The dynamic loads with frequency of BTV at SW are derived from correlation between forced vibration analysis with static loads and brake test results. And the accelerations at steering wheel were analyzed by forced vibration analysis with dynamic loads using commercial finite element program MSC/NASTRAN so that vibration characteristics of vehicle due to brake judder were investigated. Reliability of analysis results was verified through comparing the brake test results. Also, a parametric study with natural frequencies of frame, such as the 1st torsional mode and 1st bending mode, was conducted to reduce vibration amplitudes. As a result we could detect frame natural frequency conditions to improve vibration characteristics and obtained the frame model to reduce vibration amplitude.

• Journal of Mechanical Science and Technology
• /
• v.14 no.3
• /
• pp.306-313
• /
• 2000

The homogenization method and the density function method are common approaches to evaluate the equivalent material properties for design cells composed of matter and void. In this research, using a new topology optimization method based on the homogenized material with a penalty factor and the chessboard prevention strategy, we obtain the optimal layout of a structure for the natural frequency of a designated mode. The volume fraction of nodes of each finite element is chosen as the design variable and a total material usage constraint is imposed. In this paper, the subspace method is used to evaluate the eigenvalue and its corresponding eigenvector of the structure for the designated mode and the recursive quadratic programming algorithm, PLBA algorithm, is used to solve the topology optimization problem.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.3
• /
• pp.82-88
• /
• 1997

This paper derives the generalized stiffness to find dynamic characteristics and its derivatives of a continuous system. And a new sensitivity analysis method is presented by using the amount of change of generalized stiffness and vibrational mode caused by the variation of stiffness. In this paper, to get or detect appropriate results, cantilever beam and stepped beam and stepped beam are used. Deviations of sensitivity coefficient, natural frequency, and vibrational mode are calculated as result, and compared with the theoretical exact values.

• Nuclear Engineering and Technology
• /
• v.36 no.4
• /
• pp.364-373
• /
• 2004

This study investigates the fluidelastic instability characteristics of helical steam generator type tubes used in operating nuclear power plants. To obtain a natural frequency, corresponding mode shape, and participation factor, modal analyses using various conditions are performed for helical type tubes. Investigated are the effects of the number of turns, the number of supports, and the status of the inner fluid on the modal and fluidelastic instability characteristics of the tubes, which are expressed in terms of the natural frequency, the corresponding mode shape, and the stability ratio.

• Journal of Industrial Technology
• /
• v.16
• /
• pp.123-129
• /
• 1996

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and tower structures with irregular cross-sections and with arbitrary boundary conditions was developed and reported by D. H. Kim in 1974. In order to obtain the natural frequency by the presented method, the first step to take is to obtain the deflection influence surfaces. In design and analysis of any structure, the first step to be taken is to obtain this deflection influence surfaces. Any method can be used for this purpose. Then using this surfaces, deflections, slopes, moments, shears, and natural frequencies can be obtained by differentiating either the continuous function or discrete function defined at certain points. The merit of the presented method is that the natural frequency can be obtained by the deflection influence surfaces obtaining which is the first step in structural analysis.