• Nuclear Engineering and Technology
• /
• v.53 no.9
• /
• pp.2847-2858
• /
• 2021

When a nuclear reactor with rectangular fuel assemblies runs for a long time, impurities and debris may be taken into coolant channels, which may cause flow blockage, and the blocked fuel assemblies might be destroyed. Therefore, the purpose of this study is to perform a thermal-hydraulic analysis of a rectangular fuel assembly by STAR-CCM+, under the condition of one subchannel with 80% blockage ratio. A rectangular fuel assembly of the International Atomic Energy Agency (IAEA) 10 MW material test reactor (MTR) is chosen. In view of the gasket material taken into the coolant channel is close to the single side of the coolant channel, in the flow blockage accident of the Oak Ridge Research Reactor (ORRR), a new blockage category called single side blockage is attempted. The blockage positions include inlet, middle and outlet, and the blockage is set as a cuboid. It is found by simulations that the blockage redistributes the mass flow rate, and large vortices appear locally. The peak temperature of the cladding is maximum, when the blockage is located at the single side of the coolant channel inlet, and no boiling occurs in all blockage cases. Moreover, as the height of the blockage increases, the damage caused by the blockage increases slightly.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.3
• /
• pp.252-263
• /
• 2019

In order to understand the tidal current and mean flow at the west channel of Yeoja Bay in the South Sea of Korea, numerical model experiments and vorticity analysis were carried out. The currents flow north at flood and south at ebb respectively and have the reversing form in the west channel. Topographical eddies are found in the surroundings of Dunbyong Island in the east of the channel. The flood currents flow from the waters near Naro Islands through the west channel and the coastal waters near Geumo Islands through the east channel. The ebb currents from the Yeoja Bay flow out along the west and the east channels separately. The south of Nang Island have weak flows because the island is located in the rear of main tidal stream. Currents are converged at ebb and diverged at flood in the northwest of Jeokgum Island. Tidal current ellipses show reversing form in the west channel but a kind of rotational form in the east channel. As the results of tide induced mean flows, cyclonic and anticyclonic topographical eddies at the northern tip but eddies with opposite spin at the southern tip are found in the west channel of Yeoja Bay. The topographical eddies around the islands and narrow channels are created from the vorticity formed at the land shore by the friction between tidal currents and the west channel.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3540-3550
• /
• 2022

The supercritical carbon dioxide (S-CO₂) Brayton cycle is an important energy conversion technology for the fourth generation of nuclear energy. Since the printed circuit heat exchanger (PCHE) used in the S-CO₂ Brayton cycle has narrow channels, Rayleigh-Bénard (RB) convection is likely to exist in the tiny channels. However, there are very few studies on RB convection in supercritical fluids. Current research on RB convection mainly focuses on conventional fluids such as water and air that meet the Boussinesq assumption. It is necessary to study non-Boussinesq fluids. PRB convection refers to RB convection that is affected by horizontal incoming flow. In this paper, the computational fluid dynamics simulation method is used to study the PRB convection phenomenon of non-Boussinesq fluid-supercritical carbon dioxide. The result shows that the inlet Reynolds number (Re) of the horizontal incoming flow significantly affects the PRB convection. When the inlet Re remains unchanged, with the increase of Rayleigh number (Ra), the steady-state convective pattern of the fluid layer is shown in order: horizontal flow, local traveling wave, traveling wave convection. If Ra remains unchanged, as the inlet Re increases, three convection patterns of traveling wave convection, local traveling wave, and horizontal flow will appear in sequence. To characterize the relationship between traveling wave convection and horizontal incoming flow, this paper proposes the relationship between critical Reynolds number and relative Rayleigh number (r).

• Journal of the Korean Institute of Navigation
• /
• v.24 no.5
• /
• pp.423-433
• /
• 2000

Nowadays LNG has been beginning to take the place of petroleum as fuel all over the world and VLCC of LNG will take the same sea routes that had been used by VLCC tankers of petroleum in the last part of the 20th century. The transportation of LNG by a VLCC include more dangerous nature of sea peril than that of petroleum. We already know the dimensions of a disaster a LNG tanker could bring about in the case of the LNG tanker, Yuyo-Maru No. 10 in the Tokyo Bay of Japan in 1974. From the point of safety when we construct a LNG base or LNG pier in the base, the appropriate government authority and constructing company had better take sea pilots or some ships handling experts to participate in a prior consultation of the design of the project. A G/T 100,000 ton LNG base and pier were completed in November of 1996 in Inchon harbour in Korea and VLCC of LNG of G/T 100,000 ton class have been entering into the base ever since. This study was started and completed In comply with the requisition of the Sea Pilot Association of Inchon harbour in advance of the opening of the LNG base. As the entrance and exit channels leading to Inchon harbour were constructed in the years of 1930s, it was one of the most pressing works for Inchon sea pilots in 1996 to certify the method of safe passing maneuvering of a G/T 100,000 ton of LNG tanker through the Pudo narrow channel prior to commencing actual piloting of the VLCC of LNG. The authors made some mathematical models computing maneuvering of a vessel changing her course with her control surface through a narrow channel and computed maneuvering of a G/T 100,000 ton of LNG tanker and also made maneuvering simulations of the vessel by a desk-top simulator. The results of computations and simulations are well coincided with each other in qualitative aspects to assure safe passing of the VLCC of LNG.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.06a
• /
• pp.115-155
• /
• 2000

Nawadays LNG has been beginning to take the place of petroleum as fuel all over the world and VLCC tankers of LNG will take the same sea routes that had been used by VLCC tankers of petroleum in the last pat of he 20th century. The transportation of LNG by a VLCC include more dangerous nature of sea peril than that of petroleum. We already know the dimensions of a disaster a LNG tanker could bring about in the case of the LNG tanker, Yuyo-Maru No. 10 in the Tokyo Bay of Japan in 1974. From the point of safety when we construct a LNG base or LNG pier in the base, the appropriate government authority and constructing company had better take sea pilots or some ships handling experts to participate in a prior consultation of the design of the project. A G/T 100,000 ton LNG base and pier were completed in November of 1996 in Inchon harbour in Korea and LNG VLCC tankers of G/T 100,000 ton class have been entering into the base ever since. This study was started and completed to comply with the requisition of the Sea Pilot Association of Inchon harbour in advance of the opening of the LNG base. As the entrance and exit channels leading to Inchon harbour were constructed in the years of 1930s, it was one of the most pressing works for Inchon sear pilots in 1996 to certify the method of safe passing maneuvering of a G/T 100,000 ton LNG tanker through the Pudo narrow channel prior to commercing actual piloting of the LNG VLCC tanker. The author made some mathematical models computing maneuvering of a vessel changing her course with her control surface through a narrow channel and computed maneuvering of a G/T 100,000 ton LNG tanker and also made maneuvering simulations of the vessel by a desk-top simulator. The results of computations and simulations are well coincided with each other in qualitative aspects to assure safe passing of the LNG VLCC.

• Nuclear Engineering and Technology
• /
• v.37 no.6
• /
• pp.565-574
• /
• 2005

The CANFLEX Mk-V bundle is designed to improve upon the critical heat flux (CHF) characteristics of the CANFLEX Mk-IV bundle. The main difference between these two bundles is an increase in bearing pad height of about 0.3 mm in the CANFLEX Mk-IV bundle. This change in bearing pad height leads to an increase in gap flow at the bottom of the bundle, primarily eliminating the localized narrow-gap effect that limits the CHF of the CANFLEX Mk-IV bundle. The objective of this paper is to examine the effects of bearing pad height and pressure tube creep on the sheath-temperature distribution, dryout power, and dryout location, as observed ken full-scale bundle tests, between CANFLEX Mk-IV and Mk-V bundles In uncrept and crept channels. A comparison of surface-temperature differences between the top and bottom elements of the bundles showed that increasing the bearing pad height has led to a more homogeneous enthalpy distribution in subchannels of the bundle. Initial dryout locations of the CANFLEX Mk-V bundle were mainly observed at the mid-spacer plane of either the $10^{th}$ (about $80\%$) or $11^{th}$ ($20\%$) bundle in the 12-bundle string, as compared to the mid-spacer and downstream-button planes for the CANFLEX Mk-IV bundle. Dryout power and boiling-length-average (BLA) CHF values exhibit consistent trends and little scatter with varying flow conditions for both types of CANFLEX bundles in uncrept and crept channels. An increase in pressure tube creep has led to a reduction in dryout power (about $20\%$ far the $3.3\%$ crept channel and $27\%$ for the $5.1\%$ crept channel as compared to dryout powers for the uncrept channel). Increasing the bearing pad height of the CANFLEX bundle has led to an increase in the dryout power. Overall, the dryout power of the CANFLEX Mk-V bundle is 7 to $10\%$ higher than that of the CANFLEX Mk-IV bundle at the inlet temperature range of interest (i.e., between 243 and $290^{\circ}C$).

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.863-870
• /
• 2016

We investigated the physical/chemical phenomena that a slow loss of $CO_2$ inventory into sodium after the sodium-$CO_2$ boundary failure in printed circuit heat exchangers (PCHEs), which is considered for the supercritical $CO_2$ Brayton cycle power conversion system of a sodium-cooled fast reactor (SFR). The first phenomenon is plugging inside narrow sodium channels by micro cracks and the other one is damage propagation referred to as wastage combined with the corrosion/erosion effect. Experimental results of plugging shows that sodium flow immediately stopped as $CO_2$ was injected through the nozzle at $300{\sim}400^{\circ}C$ in 3 mmID sodium channels, whereas sodium flow stopped about 60 min after $CO_2$ injection in 5 mmID sodium channels. These results imply that if pressure boundary of sodium-$CO_2$ fails a narrow sodium channel would be plugged by reaction products in a short time whereas a relatively wider sodium channel would be plugged with higher concentration of reaction products. Wastage by the erosion effect of $CO_2$ (200~250 bar) hardly occurred regardless of the kinds of materials (stainless steel 316, Inconel 600, and 9Cr-1Mo steel), temperature ($400{\sim}500^{\circ}C$), or the diameter of the $CO_2$ nozzle (0.2~0.8 mm). Velocities at the $CO_2$ nozzle were specified as Mach 0.4~0.7. Our experimental results are expected to be used for determining the design parameters of PCHEs for their safeties.

• Journal of electromagnetic engineering and science
• /
• v.8 no.2
• /
• pp.41-46
• /
• 2008

A bandwidth and power efficient high speed ubiquitous sensor network(USN) for realizing a ubiquitous society is a great challenge for researcher community. In this paper we incorporate a cooperative transmission protocol within a special type of multi-code modulation to meet these requirements. Multi-code(Mc) modulation has been developed for high-speed data transmission over wireless channels. We proposed a new class of orthogonal codes for multi-code modulation which is an orthogonal subset of orthogonal codes(OSOC). Our proposed OSOC structure allows us to use only one relay to cooperate M nodes that effectively reduces the bandwidth and power requirement. This protocol is similar to spread-spectrum(SS) technique that can reduce both broad and narrow band jamming.

• Journal of KSNVE
• /
• v.5 no.3
• /
• pp.373-383
• /
• 1995

From the viewpoint of the structural design, the principal problem of the heat exchanger is the potentiality of structural instabilities due to the fluid loading effect during operations. Excessive fluid loading may give rise to permanent deformation of tube and would enentually result in collapse of heat exchanger, which would cause an obstruction of the fluid flow in the narrow channels. In this study, a fluid-structural interaction model was developed to investigate analtically the vibration characteristics of thin rectangular tube used in the heat exchanger. The model consists of two flat plates separated by fluid. The effects of the fluid in the tube was stuided. For analyses, the natural frequency coefficients of the model were investigated for the plate aspect ratios, channel heights, and boundary conditions. As conclusions, the natural frequency coefficients of the tube is found to be affected largely by the fluid loading and the channel heights.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.3
• /
• pp.390-394
• /
• 2003

It is very important to simulate various mobile communication channels for the reliable system design and performance tests. Therefore, a new method is proposed in this paper to improve the conventional one for the purpose of the efficient channel simulation having various characteristics. A newly proposed method can simulate any narrow band channel very efficiently from the given Doppler power spectrum model. Also, it has many simulation advantages considering the variety of wireless channel conditions since parameters related with channel characteristics, such as a signal power, signal to noise ratio, direct signal power ratio, etc., can be easily changed according to various propagation environments to be tested.