• Bulletin of the Korean Chemical Society
• /
• v.31 no.7
• /
• pp.1833-1834
• /
• 2010

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.354.1-354.1
• /
• 2016

Nanoporous gold (NPG) is a very promising material in various fields such as sensor, actuator, and catalysis because of its high surface to volume ratio and conducting nature. In this study, we fabricated a NPG based amperometric sensor on a glass substrate by means of co-sputtering of Au and Si. During the sputtering process, we found the optimum conditions for heat treatment to reduce the residual stress and to improve adhesion between NPG films and the glass substrate. Subsequently, Si was selectively etched from Au-Si alloy by KOH solution, which forms nanoporous structures. Scanning electron microscopy (SEM) and auger electron spectroscopy (AES) were used to estimate the structure of NPG films and their composition. By employing appropriate heat treatments, we could make very stable NPG films. We tested the performance of NPG sensor with aniline molecules, which shows high sensitivity for sensing low concentration of aniline.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.429-429
• /
• 2009

Nanoporous anodic alumina membranes (NAAM) with high-density through-hole pores fabricated by hard anodization of aluminum in 0.3 M oxalic acid under the applied voltage of 40 (mild anodization), 80, 100, 120 and 140 V were investigated. The current-time responses monitored using a PC-controlled anodization cell and the corresponding pore structures attainable from field-enhanced scanning electron microscopy (FE-SEM) were analyzed in order to establish the optimum fabrication process. The nanoporous structure can be produced for all the voltage conditions, while the stabilized through-hole pore formation seems to occur at 40, 80 and 140 V. The growth rate under 140 V hard anodization was over 30 times higher than under 40 V mild anodization (1.5 um/hr).

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.141-144
• /
• 2009

In this study, used simplest sandwich cells containing $Ru2^+$ liquid electrolytes in order to clarify the role of nanoporous $TiO_2$ electrodes. And, the cell structure is as follow: $F:SnO_2$ glass/ nanoporous $TiO_2$/ tris(2,2'-bipyridy)ruthenium(ll) colplex [$Ru(bpy)_3(PF_6)_2$] in acetonitrile/ $F:SnO_2$ glass. The result, we found that ECL intensities increased rapidly by use of cathodes with nanoporous $TiO_2$ layers. And, porous $TiO_2$ electrodes were confirmed to be efficient for ECL devices as well as solar cell devices. It is thought that the increases in the ECL intensities may be associated with both formation of $Ru^+$ in porous $TiO_2$ electrodes and the process taking place after reduction of $Ru^+$ which occurs in the nanoporous electrodes.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.52-52
• /
• 2002

Recently, nanoporous low-k materials using porogen (pore generating material) template method have gained much attraction due to the feasible advantage of dielectric constant decrease with the increase of porogen content, which is burning out and making air void by thermal curing. In nanoporous thin films, further, control of pore size and its distribution is very important to retain suitable thermal, mechanical and electrical properties. In this study, nanoporous low-k films were prepared with MTMS-BTMSE copolymer and porogen. The effect of interaction of copolymer matrix and porogen on pore size and distribution was comparatively to investigate with molecular structure and end functional group. The characterization of nanoporous thin film prepared was also performed using various techniques including NMR, GPC, Ellipsometer, FE-SEM, TGA, and FT-IR.

• KSBB Journal
• /
• v.27 no.1
• /
• pp.45-50
• /
• 2012

In this paper, we investigated the effect of nanostructure on the cell behaviors such as adhesion and growth rate. Nanoporous structures with various diameters (30, 40, 45, 50, 60 nm) and 500 nm of the depth were fabricated using the anodizing method. The water contact angle of the surface consisting of nanopores with 30 nm diameter was 40 degree and those were 60~70 degree in cases of nanopores with over 40 nm diameter. Hela cells were cultivated on various nanoporous structure surface to investigate the cell behavior on nanostructure. As a result, Hela cells preferred 30 nm diameter nanoporous surface that has lower water contact angle. This result was confirmed by protein adsorption experiment and scanning electron microscope investigation.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3749-3754
• /
• 2012

Nanoporous carbons with a high specific surface area were prepared directly from thermoplastic acrylic resin as carbon precursor and MgO powder as template by carbonization over the temperature range, $500-1000^{\circ}C$. The effect of the carbonization temperature on the pore structure and $CO_2$ adsorption capacity of the obtained porous carbon was examined. The textural properties and morphology of the porous carbon materials were analyzed by $N_2/-196^{\circ}C$ and $CO_2/0^{\circ}C$ adsorption/desorption isotherms, SEM and TEM. The $CO_2$ adsorption capacity of the prepared porous carbon was measured at $25^{\circ}C$ and 1 bar and 30 bar. The specific surface area increased from 237 to $1251m^2/g$, and the total pore volumes increased from 0.242 to $0.763cm^3/g$ with increasing the carbonization temperature. The carbonization temperature acts mainly by generating large narrow micropores and mesopores with an average pore size dependent on the level of carbonization of the MgO-templated nanoporous carbons. The results showed that the MgO-templated nanoporous carbons at $900^{\circ}C$ exhibited the best $CO_2$ adsorption value of 194 mg/g at 1 bar.

• Journal of the Korean Chemical Society
• /
• v.66 no.6
• /
• pp.436-441
• /
• 2022

Because the nanoporous electrodes has large electrochemical surface areas, extensive studies have been focused on their fabrication methods. In this paper, a method for introducing a nanoporous gold (NPG) structure on the surface of an ultramicroelectrode (UME) using potentiostatic anodization was investigated. A well-defined NPG structure was introduced on the surface of the UME when a potential of 1.3 V was applied in 0.1 M phosphate buffer solution (pH 8) containing 1 M KCl. The anodic oxidation efficiency was investigated by observing the effect of the applied potential, the reaction time, and the size of the electrode on the roughness factor (R_f) of the prepared NPG-UMEs. In a short time of about 10 minutes, NPG-UME with a large R_f value of about 2000 could be prepared, which could be effectively used for electrochemical glucose detection. The results shown in this work are expected to have great applicability when performing electrochemical analysis with a small sample volume.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.176-181
• /
• 2009

In this work, a new type of DSCs based on nanoporous FTO structure is being developed for research aimed at low-cost high-efficiency solar cell application. The nanoporous FTO materials have been prepared through the sol-gel combustion method followed by thermal treatment at $450{\sim}850[^{\circ}C]$. The properties of the nanoporous FTO materials were investigated by IR spectra, BET and TEM analyses, and the photovoltaic performance of the prepared DSCs were examined. It can be seen from the result that the nanoporous FTO exhibited good transparent conductive properties, well suited for DSCs application.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.3
• /
• pp.125-130
• /
• 2011

We describe that the surface and thickness of nanoporous $WO_3$ fabricated by both light-induced and light-absent anodization are affected by pre-annealing process from $200^{\circ}C$ to $600^{\circ}C$. As a result, the nanoporous $WO_3$ with a thickness of $1.83{\mu}m$ can be achieved by anodization for 6 hours after pre-annealing at $400^{\circ}C$ without illumination of light. Moreover, the thickness of nanoporous $WO_3$ fabricated by pre-annealing is thicker than that of $WO_3$ prepared by non-annealing process. However, the light illumination during anodization leads to convert the crystalline structure obtained by pre-annealing, which interfere the growth of nanoporous $WO_3$. In this paper, we discuss about the growth mechanism of these different nanoporous $WO_3$ films.