• 수산해양기술연구
• /
• 제51권4호
• /
• pp.561-566
• /
• 2015

In this study, the effect of temperature effect of the rubber matrix filled with nano sized silica particles composites with silica volume fraction of 19-25% was investigated by the Charpy impact test. The Charpy impact test was conducted in the temperature range from $-40^{\circ}C$ to $0^{\circ}C$. The critical energy release rate GIC of the rubber matrix composites filled with nano sized silica particles was considerably affected by temperature and it was shown that the maximum value was appeared at higher temperature between temperature tested and it was shown that the value of GIC increases as temperature tested increases. The major fracture mechanisms were matrix deformation, silica particle debonding and delamination, microcrack between particles and matrix, and/or pull out between particles and matrix which is ascertained by SEM photographs of Charpy impact surfaces fracture.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.260-263
• /
• 2015

Epoxy/micro-sized alumina composite was prepared and the effects of alumina content on the electrical and mechanical properties were investigated in order to develop an insulation material for gas insulated switchgear (GIS). Nano-sized alumina (average particle size: 30 μm) was also incorporated into the epoxy/micro-sized alumina composite. An electrical insulation breakdown strength test was carried out in sphere-sphere electrodes and the data were estimated by Weibull statistical analysis. Tensile strength was measured at a crosshead speed of 10 mm/min using a universal testing machine. Alumina content was varied from 0 wt% to 70 wt%.). As micro-sized alumina content increased, insulation breakdown strength increased until 40 wt% alumina content and decreased after that content. The tensile strength of a neat epoxy system was 82.2 MPa and that value for 60 wt% alumina content was 91.8 MPa, which was 111.7% higher than inthe neat epoxy system. The insulation breakdown strength of micro-sized alumina (60 wt%)/nano-sized alumina (1 phr) glycerol diglycidyl ether (GDE) (1 phr) composite was 54.2 MPa, which was 116% higher than the strength of the system without nano-sized alumina.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.472-475
• /
• 2010

나노 알루미늄과 물의 연소 반응을 정상상태 층류 연소로 모델링하여 이론적 접근을 하였으며 압력에 따른 화염전파속도의 영향을 조사하였다. 물의 상변화에 따른 증발열을 고려하였으며 다양한 압력 영역(0.1MPa ~ 10MPa)에 대한 연소 특성을 살펴보았다. 모델링 영역을 1)물+알루미늄 2)증기+알루미늄 3)반응영역으로 나누었으며 영역의 방정식을 구성하고 화염속도에 대한 해석적 해를 구하였다. 입자크기에 따른 연소실 압력의 영향을 도출하여 시험결과와 비교, 분석 하였다.

• 한국표면공학회지
• /
• 제56권6호
• /
• pp.437-442
• /
• 2023

This research aims to enhance the efficiency of Pt/C catalysts due to the limited availability and high cost of platinum in contemporary fuel cell catalysts. Nano-sized platinum particles were distributed onto a carbon-based support via the polyol process, utilizing the metal precursor H₂PtCl₆·6H₂O. Key parameters such as pH, temperature, and RPM were carefully regulated. The findings revealed variations in the particle size, distribution, and dispersion of nano-sized Pt particles, influenced by temperature and pH. Following sodium hydroxide treatment, heat treatment procedures were systematically executed at diverse temperatures, specifically 120, 140, and 160 ℃. Notably, the thermal treatment at 140 ℃ facilitated the production of Pt/C catalysts characterized by the smallest platinum particle size, measuring at 1.49 nm. Comparative evaluations between the commercially available Pt/C catalysts and those synthesized in this study were meticulously conducted through cyclic voltammetry, X-ray diffraction (XRD), and field-emission scanning electron microscopy-energy dispersive X-ray spectroscopy (FE-SEM EDS) methodologies. The catalyst synthesized at 160 ℃ demonstrated superior electrochemical performance; however, it is imperative to underscore the necessity for further optimization studies to refine its efficacy.

• Journal of Ceramic Processing Research
• /
• 제22권2호
• /
• pp.169-178
• /
• 2021

In this work, in-flight synthesis route of Ga doped ZnO (GZO) nano-powders was investigated experimentally and numerically, using Radio-Frequency (RF) induction plasmas. For experimental study, mixture of micron-sized ZnO and Ga₂O₃ powders were treated by RF induction plasmas, then, the as-treated powders were retrieved from reactor bottom and filtration for characterization. For numerical study, single particle model was combined with two-dimensional simulation code of RF induction plasma to predict the particle behaviors of ZnO and Ga₂O₃ depending on their sizes. First, experimental results showed that filtration-retrieved powders were characterized as GZO nano-powders although gallium content can be decreased due to Ga₂O₃ decomposition into sub-oxides at the elevated temperatures. From reactor bottom, however, spherical structures consisting of Ga₂O₃ and ZnO particles were observed in sub-millimeter sizes. Numerical results predicted that micron-sized (≤ 10 ㎛) ZnO and Ga₂O₃ particles can vaporize easily during the flight of plasma, while particles with the sizes of 25~100 um were simulated to be partially evaporated or unevaporated. Comparing these experimental and numerical results indicates that GZO nano-powders can be synthesized from vapor species of ZnO and Ga₂O₃, which are primarily produced by in-flight treatment of micron-sized ZnO and Ga₂O₃ powders in RF induction plasmas.

• 한국재료학회지
• /
• 제21권7호
• /
• pp.396-402
• /
• 2011

In this study, by using tin chloride solution as a raw material, a nano-sized tin oxide powder with an average particle size below 50 nm is generated by a spray pyrolysis process. The properties of the generated tin oxide powder depending on the inflow speed of the raw material solution are examined. When the inflow speed of the raw material solution is 2 ml/min, the majority of generated particles appear in the shape of independent polygons with average size above 80-100 nm, while droplet-shaped particles show an average size of approximately 30 nm. When the inflow speed is increased to 5 ml/min, the ratio of independent particles decreases, and the average particle size is approximately 80-100 nm. When the inflow speed is increased to 20 ml/min, the ratio of droplet-shaped particles increases, whereas the ratio of independent particles with average size of 80-100 nm decreases. When the inflow speed is increased to 100 ml/min, the average size of the generated particles is around 30-40 nm, and most of them maintain a droplet shape. With a rise of inflow speed from 2 ml/min to 5 ml/min, a slight increase of the XRD peak intensity and a minor decrease of specific surface area are observed. When the inflow speed is increased to 20 ml/min, the XRD peak intensity falls dramatically, although a significant rise of specific surface area is observed. When the inflow speed is increased to 100 ml/min, the XRD peak intensity further decreases, while the specific surface area increases.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.443-446
• /
• 2006

Carbon-supported Platinum (Pt) is the potential electro-catalyst material for anodic and cathodic reactions in fuel cell. Catalytic activity of the metal strongly depends on the particle shape, size and distribution of the metal in the porous supportive network. Conventional preparation techniques based on wet impregnation and chemical reduction of the metal precursors often do not provide adequate control of particle size and shape. We have proposed a novel route for preparing nano sized Pt colloidal particles in solution by oxidation of ethylene glycol. These Pt nano particles were deposited on large surface area carbon support. The process of nano Pt colloid formation involves the oxidation of solvent ethylene glycol to mainly glycolic acid and the presence of its anion glycolate depends on the solution pH. In the process of colloidal Pt formation glycolate actsas stabilizer for the Pt colloidal particle and prevents the agglomeration of colloidal Pt particles. These mono disperse Pt particles in carbon support are found uniformly distributed in nearly spherical shape and the size distribution was narrow for both supported and unsupported metals. The average diameter of the Pt nano particle was controlled in the range off to 3 nm by optimizing reaction parameters. Transmission electron microscopy, CV and RRDE experiments were used to compliment the results.

• Advances in materials Research
• /
• 제1권3호
• /
• pp.169-182
• /
• 2012

In this paper the intrinsic influence of micron-sized nickel particle reinforcements on microstructure, micro-hardness tensile properties and tensile fracture behavior of nano-alumina particle reinforced magnesium alloy AZ31 composite is presented and discussed. The unreinforced magnesium alloy (AZ31) and the reinforced nanocomposite counterpart (AZ31/1.5 vol.% $Al_2O_3$/1.5 vol.% Ni] were manufactured by solidification processing followed by hot extrusion. The elastic modulus and yield strength of the nickel particle-reinforced magnesium alloy nano-composite was higher than both the unreinforced magnesium alloy and the unreinforced magnesium alloy nanocomposite (AZ31/1.5 vol.% $Al_2O_3$). The ultimate tensile strength of the nickel particle reinforced composite was noticeably lower than both the unreinforced nano-composite and the monolithic alloy (AZ31). The ductility, quantified by elongation-to-failure, of the reinforced nanocomposite was noticeably higher than both the unreinforced nano-composite and the monolithic alloy. Tensile fracture behavior of this novel material was essentially normal to the far-field stress axis and revealed microscopic features reminiscent of the occurrence of locally ductile failure mechanisms at the fine microscopic level.

• 자원리싸이클링
• /
• 제16권1호
• /
• pp.28-36
• /
• 2007

폐 ITO 타겟을 염산에 용해시킨 복합 산용액을 원료로 하여 자체기술에 의해 개발한 분무열분해 반응장치를 통하여 평균입도가 50nm이하인 나노 ITO 분말을 제조하였으며, 반응온도 및 원료용액의 농도 등의 반응인자들의 변화에 따른 ITO 분말의 특성을 파악하였다. 반응온도가 $800^{\circ}C$로부터 $1100^{\circ}C$로 변화함에 따라 생성된 ITO 분말의 평균 입도는 40nm로부터 100nm정도까지 증가하고 있었으며, 조직도 점점 치밀화되면서 각각의 입자들이 독립된 다각형 형태를 나타내었으며, 입도분포는 더욱 불균일하게 나타나고 있었다. 또한 반응온도 증가에 따라 XRD 피크의 강도는 증가하였으며 비표면적은 감소하고 있었다. 원료용액 내의 인듐 성분의 농도가 50g/l로부터 400g/l로 증가됨에 따라 생성된 ITO 분말의 평균입도는 점점 증가하는 반면 입도분포는 더욱 불균일 하였다. 농도가 50g/l인 경우에는 ITO 분말의 평균입도는 30nm 이하이면서 입도분포는 비교적 균일하게 나타나고 있었다. 반면 농도가 포화농도에 가까운 400g/l인 경우에는 분말들의 입도분포는 20nm 정도부터 100nm 이상까지 공존하는 매우 불균일한 형태를 나타내고 있었다. 농도가 증가함에 따라 XRD 피크의 강도는 점점 증가하였으며 비표면적은 점점 감소하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권4호
• /
• pp.508-514
• /
• 2010

본 논문은 커먼레일 디젤엔진의 정속운전시 배출되는 나노크기의 입자상 물질을 분석하는데 초점을 두었다. 디젤산화촉매 후단에서 나노입자상 물질의 개수농도 저감수준은 크지 않았으나 매연여과장치 후단에서 분석한 결과 1,000배 정도 저감되는 결과를 확인하였다. 고속 고부하 조건에서는 매연여과장치의 자연재생 효과로 인해 입자상 물질은 증가하였다. 연료분사시기를 BTDC $6^{\circ}CA$ 에서 ATDC $4^{\circ}CA$까지 지각시킨 결과 입자상 물질의 개수농도는 감소하였지만 최지각 조건인 ATDC $9^{\circ}CA$에서는 증가하는 결과를 확인하였다. EGR 적용시 핵화모드 입자상 물질은 저감되는 경향을 보였으며 축적모든 입자는 증가하였다.