• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.332-340
• /
• 2023

This study investigated the effects of nanoparticles on the fracture toughness of cement mortar. Three-point bending tests, compressive tests, and slump tests were conducted on cement mortars reinforced with carbon nanotubes(CNTs), nanosilica(NS), and nano calcium carbonate(NC), respectively. Cement mortar with a water-to-cement ratio and a sand-to-cement ratio of 0.45 and 1.5, respectively, and reinforced with 0 and 2 vol.% of 19.5 mm steel fibers, respectively, was used. Reinforcement with nanoparticles partially improved the fracture toughness and compressive strength of the cement mortar. However, in the case of cement mortar reinforced with steel fibers, the reinforcement with nanoparticles was found to reduce the flowability of the mortar, adversely affecting the dispersion of steel fibers, and ultimately leading to a decrease in fracture toughness, contrary to the intended enhancement. Additional research is needed to improve the decrease in mortar fluidity caused by the reinforcement with nanoparticles.

• Polymer(Korea)
• /
• v.36 no.6
• /
• pp.727-732
• /
• 2012

Baroplastic poly(butyl acrylate) (PBA)/polystyrene (PS) blends were prepared by mixing PBA and PS emulsions synthesized by cationic and anionic surfactant, respectively. Interestingly, the heterocoagulation of nanoparticles have found to be affected strongly by emulsion concentration but the blends have been prepared with almost same compositions regardless of the amount of reactants. Utilizing this method, PBA/PS/Si hybrid nano-blends were prepared successfully via electrostatic attraction forces between PBA, PS and silica nanoparticles. The hybrid nano-blend having 2 or 5 wt% of silica was then processed to a semi-transparent film at $25^{\circ}C$ under 13.8 MPa for 10 min, which showed 3.0 MPa of tensile strength and 25 MPa of elastic modulus. Therefore, the heterocoagulation technique can be used for preparing baroplastics with uniform compositions of polymer and silica nanoparticles.

• Particle and aerosol research
• /
• v.7 no.4
• /
• pp.113-121
• /
• 2011

The aerosol nanoparticles are suspected to be exposed to workers in nanomaterial manufacturing facilities. However, the exposure assessment method has not been established. One of important issues is to characterize background level of nanoparticles in workplaces. In this study, intensive aerosol measurements were made at a $TiO_2$ manufacturing laboratory for five consecutive days in May of 2010. The $TiO_2$ nanoparticles were manufactured by the thermal-condensation process in a heated tube furnace. The particle number size distribution was measured using a scanning mobility particle sizer every 5 min, in order to detect particles ranging from 14.5 to 664 nm in diameter. Total particle number concentration shows a severe diurnal variation irrespective of manufacturing process, which was governed by nanoparticles smaller than 50 nm in diameter. During the background monitoring periods, significant peak concentrations were observed between 2 p.m. and 3 p.m. due to the infiltration of secondary aerosol particles formed by photochemical smog. Although significant increase in nanoparticle concentration was also observed during the manufacturing process twice among three times, these particle peak concentrations were lower than those observed during the background measurement. It is suggested that the investigation of background particle contamination is needed prior to conducting main exposure assessment in nanomaterial manufacturing workplaces or laboratories.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.103-112
• /
• 2003

Various kinds of metals were coated on synthetic graphite in order to investigate the relationship between film characteristics and their electrochemical performance. Gas suspension spray coating method was employed for the coating of synthetic graphite. In our experimental range, all of the metal coated synthetic graphite showed the higher capacity than that of raw material at high C-rate mainly due to decrease in impedance of passivation film. In cyclic voltammetry experiments, silver-coated and tin-coated graphite anodes found the lithium-alloy reaction. Considering smaller amount of metal coating, the most increase in discharge capacity was caused by improvement of conductivity of the electrode. When single-component metal was coated, silver-coated graphite anode exhibited the highest discharge capacity and better cycleability. Double components of silver-nickel coated active material showed the highest discharge capacity, rate capability and the best cycle performance in the range of our experiments.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.976-983
• /
• 2004

In high-density hard disk drives, the slider should be made to fly close to the magnetic recording disk to generate better signal resolution and at an increasingly high velocity to achieve better data rate. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation. Contamination particles in the hard disk drive can cause serious problems including slider crash and thermal asperities. We investigated the number and the sizes of particles generated in the hard disk drive, operating at increasing disk rotational speeds, in the CSS mode. CNC (condensation nucleus counter) and PSS (particle size selector) were used for this investigation. In addition, we examined the particle components by using SEM (scanning electron microscopes), AES (auger electron spectroscopy), and TOF-SIMS (time of flight-secondary ions mass spectrometry). The increasing disk rotational speed directly affected the particle generation by slider disk interaction. The number of particles that were generated increased with the disk rotational speed. The particle generation rate increased rapidly at motor speeds above 8000 rpm. This increase may be due to the increased slider disk interaction. Particle sizes ranged from 14 to 200 nm. The particles generated by slider disk interaction came from the lubricant on the disk, coating layer of the disk, and also slider surface.

• Resources Recycling
• /
• v.16 no.5
• /
• pp.36-40
• /
• 2007

Platinum plays an important role in many applications because of its extraordinary physical and chemical properties. All these applications require the use of platinum in the finely divided state. Therefore the preparation of platinum nanoparticles by reducing platinum-surfactant salt with reducing agent in the solution was investigated in this study. The net interaction between C14TABr and $H_2[PtCl_6]$ in aqueous solution results in the formation of $[C14TA]_2[PtCl_6]$. The concentration of C14TABr and the concentration of $H_2[PtCl_6]$ has to be above cmc and 0.32 mM, respectively in order to obtain complex-micelle aggregation for mono dispersed Pt particles. Pt particle size increases with increasing $H_2[PtCl_6]$ and C14TABr concentration. And the shape of Pt particles was well controlled with increasing surfactant concentration.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.1
• /
• pp.145-149
• /
• 2023

High-resolution images of surfaces provide detailed information on pores or shapes with specific sizes ranging from nano sizes to micrometers. However, it is not yet clear to determine an efficient association for pores or shapes from high-resolution images of surfaces. For the efficient association of pores and shapes, the surface characteristics of the device were considered as fractal dimensions by taking SEM photographs and binarizing the images. The fractal program was directly coded for surface analysis of the device. The device surface characteristics and electrical characteristics are thought to be related to the fractal dimension. The fractal dimension decreased with an increase in internal pores. The density and grain boundary of particles, which are structural characteristics of the device surface, were related to the fractal dimension. The particle size decreased with an increase in the fractal dimension and was uniformly formed. When the particles were uniformly formed, fewer pores were present and the fractal dimension increased.

• Analytical Science and Technology
• /
• v.19 no.6
• /
• pp.468-472
• /
• 2006

This paper was described that the preparation of polymetylmethacrylate (PMMA) microsphere and coating of vitamin C onto surface of the prepared PMMA microsphere for application of cosmetic materials. The PMMA microsphere with various sizes can be obtained by change of reaction condition such as reaction temperature and reaction time. The coating of vitamin C on the surface of PMMA microsphere by using cyclodextrin as binder can be achieved to 30 wt-% in water/ethanol mixture. The vitamin C coated with cyclodextrin was stabilized during 56 days at $40^{\circ}C$. The color of the coated Vitamin C was changed from white to dark yellow after 14 days at $40^{\circ}C$. The vitamin C coated with cyclodextrin on the surface of PMMA microsphere can be sufficiently used for cosmetic materials.

• Analytical Science and Technology
• /
• v.22 no.3
• /
• pp.247-253
• /
• 2009

Porous silicon films are electrochemically etched from crystalline silicon wafers in an aqueous solution of hydrofluoric acid(HF). Careful control of etching conditions (current density, etch time, HF concentration) provides films with precise, reproducible physical parameters (morphology, porosity and thickness). The etched pattern could be varied due to (1) current density controls pore size (2) etching time determines depth and (3) complex layered structures can be made using different current profiles (square wave, triangle, sinusoidal etc.). The optical interference spectrum from Fabry-Perot layer has been used for forensic applications, where changes in the optical reflectivity spectrum confirm the identity. We will explore a method of identifying the specific pattern code and can be used for identities of individual code with porous silicon based encoded nanosized smart particles.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.366-371
• /
• 2010

Accompanying the rapid advance of nanotechnology, various nano-particles have shown promise as strong antimicrobial agents against a broad spectrum of microorganisms. These nanoparticles also have potential applications in medical devices, water treatments systems, environmental sensors and so on. However, with increasing concerns about the impact of engineered nanoparticles, many researchers are recently reporting the cytotoxicity of nanoparticles. In this review paper, we summarized the antimicrobial activities and mechanisms of various kinds of engineered nanoparticles to imprale understanding about these characteristics of nanoparticles.