• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.12-18
• /
• 1999

This research was undertaken to do the technical and economical feasibility study of membrane water treatment system. For the technical feasibility study, batch water treatment system using UF(ultrafiltration) was set up and several experiments were carried out. The performance of the UF membrane was tested in terms of turbidity. The experimental results showed that the UF membrane process produced less than 1 NTU water regardless of input water turbidity. For the economical feasibility study, the cost model was analyzed and programmed for simulation. Also costs of the membrane water treatment and the conventional treatment were evaluated. The simulation results showed that the unit production cost increased when design flow or permeate flow decreased. The production cost of membrane water treatment system was lower than that of the conventional system. Both technical and economical feasibility study showed that the UF membrane water purification system was a very competitive water purification process.

• Korean Journal of Ecology and Environment
• /
• v.45 no.3
• /
• pp.314-321
• /
• 2012

To quantitatively assess the effects of turbidity on egg development and larval fish survival, a laboratory fish rearing experiment was applied to different life stages (newly hatched larval stage, juvenile stage and pre-adult stage) of the Zacco platypus, one of the most universal and tolerant species in Korea. According to the stress index of turbidity in water with exposure time, three different treatments, including a reference condition (1~7 NTU) as well as intermediate (20~150 NTU) and high turbidity conditions (400~1,000 NTU) were applied, and egg hatching and larval fish mortality rates were observed. The mortality rates of newly hatched larval fish were significantly different among treatments (ANOVA, $F_{2,3}$=17.79, p<0.05). Average rates of survival to hatching were 20.9% (${\pm}0.1%$) for reference condition, 11% (${\pm}6.9%$) for intermediate level and 3.2% (${\pm}3.7%$) for high level conditions, respectively. A sudden change of mortality at the high level was observed within 5 days of the experiment. About 84% of juvenile fish survived until 20 experimental periods under conditions of reference turbidity, while survival under conditions of intermediate turbidity was over 80% of larval fish until day 13 of the experiment, but dropped to less than 10% after day 14 and 15 of two experiments. Fish mortality appeared from day 6 of the high turbidity experiment, and 50% mortality was achieved at day 9 to 10 of experiment. Full mortality occurred at day 14 of the experiment (RM-ANOVA, $F_{2,38}$, p<0.005). In the pre-adult stage experiment, no mortality was observed during the experiment at reference level treatment (20 days), while only slight mortality rates were observed for both intermediate and high levels until day 5 of the experiment, however, no further fish died in either experiment. It was significantly different compared to reference condition (RM-ANOVA, $F_{2,20}$=8.28, p<0.01), but no difference was observed between intermediate and high level conditions. Consequently, this tolerant species has been determined to be well adapted to high levels of turbidity in its adult stage, but more vulnerable throughout earlier life stages.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.270-276
• /
• 2020

3D printing is an additive manufacturing technology that can produce complex shapes in a single process for a range of materials, such as polymers, ceramics, and metals. Recent 3D printing technology has developed to a level that enables the mass-production through an improvement of the printing speed and the continuous development of applicable materials. In this study, 3D printing technology using a laser was applied to manufacture a heat exchanger for an air compressor in a railway vehicle. First, the optimal design of the heat exchanger was carried out by focusing on weight reduction and compactness as a shape suitable for 3D printing. Based on the design derived, heat exchanger prototypes were made of AlSi10Mg alloy material by applying the SLM technique. Moreover, the manufactured prototypes were attached to an existing air compressor, and the heat exchange performance of the compressed air was tested. The test results of the 3D printed prototypes showed a heat exchange performance of approximately 80% and 85% at low and high-pressure, respectively, compared to the existing heat exchanger. From the 𝓔-NTU method results with an external cooling air condition similar to that of the existing heat exchanger, the calculated heat transfer amount of 3D printed parts showed similar performance compared to the existing heat exchanger. As a result, the 3D printed heat exchanger is lightweight with good performance.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.9
• /
• pp.542-547
• /
• 2017

This paper was to analyze the membrane characterization of hydrophilicity, surface morphology and membrane chemical anlysis of three commercial microfiltration/ultrafiltration membranes, and evaluate the filtration performance of a seawater to assess the availability for pretreatment of desalination process. From the results of contact angle, Mem-3, fabricated with polyacrylonitrile, was highly hydrophilic. It find out that Mem-3 has more anti-biofouling property. In Field emission scanning electron microscope (FESEM), Mem-1 (polyethylene) and Mem-2 (Polyvinylidenefluoride) showed the sponge-like shape and Mem-3 showed finger-like shape. Membrane chemical analysis by energy dispersive spectrometer (EDS) presented that Mem-2 was mostly fluoride and Mem-3 had s high ratio of N (32.47%) due to the nitrile group. The permeation flowrate per time on suction pressures using deionized water (D.I. water) tends that permeation rate of Mem-3 more increased when the pressure was increased compared to other membranes. From the results of turbidity and total suspended solids (TSS) removal, turbidity of permeate was 0.191 NTU to 0.406 NTU and TSS was 2.2 mg/L to 3.0 mg/L in all membranes, indicating that it was not suitable for the pretreatment of seawater desalination by short-term experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.23-30
• /
• 2016

In this study, the heat transfer and pressure drop characteristics were evaluated for multi-tube $CO_2$ water heaters with lengths of 4.5 m and 7.5 m. The evaluation was done using the -NTU method, and the results were compared with experimental data. Water flows through the shell side of the water heater, while $CO_2$ flows through 8 inner tubes. The heater uses a counter-current design to maximize the heat transfer efficiency. The energy balance equation describing the flows of $CO_2$ and water for each node is set up using the section-by-section method. The calculated heat transfer rates agree well with the experimental data within ${\pm}5%$ error. The outlet water temperature decreased linearly with the increase of the water flow rate. The calculated heat transfer rates agreed well with the experimental data within ${\pm}3%$ error. The results show that the heat transfer rate increases almost linearly with the increase of water flow rate or $CO_2$ inlet temperature in both the 4.5-m and 7.5-m water heaters, whereas the water outlet temperature linearly decreases with the increase of the water flow rate. The comparison of the $CO_2$ pressure drop between the calculation and experiment results shows good agreement at the high $CO_2$ flow rate within 5 % error, but the value is about 20 % higher in the experimental pressure drop at the low $CO_2$ flow rate.

• Korean Journal of Ecology and Environment
• /
• v.41 no.spc
• /
• pp.27-34
• /
• 2008

The vertical distribution and origin of particulate organic matter (POM) were investigated in Shingu reservoir on 4th July (pre-monsoon) and 7th August (post-monsoon) 2006. High turbid water (120 NTU) were found at 4.5 m water depth in postmonsoon period. The average C/N ratio of POM was about 5.70 and 6.96 in surface water and bottom water, respectively in pre-monsoon period, exhibiting the close values to its ratio in phytoplankton cell. However, the average C/N ratio was 7.10 in surface water and 12.81 in bottom water in post-monsoon period. In addition, the ${\delta}^{13}C$ values of POM in pre-monsoon period ranged from -25.1%o to -26.1%o in whole water column, but the ${\delta}^{13}C$ values of POM in post-monsoon period showed relatively wide range between -23.2%o and -27.5%o. The apparently lighter values (average -27.5%o) in near bottom water (4.5 m water depth) demonstrate that POM in high turbid water in post-monsoon period may be derived from the outside terrestrial plants through heavy rainfall during the summer monsoon period. The present study suggests that carbon and nitrogen stable isotope ratios as well as C/N ratios should be useful indexes to clarify the origin of POM.

• Journal of Wetlands Research
• /
• v.12 no.2
• /
• pp.25-33
• /
• 2010

Three plans(induction of water flow, supply of oxygen into water, control of fish causing resuspension of solids) proposed to improve the pollutant removal efficiency of Sihwa Constructed Wetland(CW) were estimated by considering the their efficiency and application to the wetland. After construction of facility for induction of water flow in lower part(W 122m${\times}$L 103m) of the wetland, the mean removal efficiencies of BOD, SS, TN and TP were in range of 12.8~37.4% and BOD was showing the highest efficiency. This result indicates that water flows is one of very important factors in the pollutant removal of wetland, especially near the outlet of a large scale wetland such as Sihwa CW. Dissolved oxygen(DO) concentrations after operation of two oxygen supply systems such as Air Bubble Diffuser and Surface Aeration System increased 15.5% and 27.2%, respectively. For maintaining effective DO concentration in Sihwa CW, the operation of oxygen supply system may be desirable during midnight to dawn in the location in which DO concentration is not enough, for instance less than 2 mg/L in CW. In experiments of the fish removal from Sihwa CW, the mean turbidity was lower in test site(6.2 NTU) than control site(10.6). The removal efficiency of thurbidity by th fish removal from the wetland was 41.5%. Therefore, a relevant fish management through a periodical monitoring of fish and turbidity is needed.

• Journal of agriculture & life science
• /
• v.45 no.5
• /
• pp.97-103
• /
• 2011

The purpose of this study was to analyze the pollutant reduction effect for non-irrigated crop land by nonpoint source pollution control. For a field scale monitoring, 6 plots (5m width and 22m length) and 3 sediment traps were installed. At the outlet of each plot, the stage gauges were installed for runoff monitoring. For a rainfall monitoring, tipping bucket rain gage was installed within the experiment site. Through the artificial irrigation, runoff from the plots were monitored. The SS, TOC, T-N, T-P, COD, NTU of sampled water were analyzed by standard methods. The SS, TOC, T-N, T-P, COD, NTU concentration of initial runoff were 15.00, 1.54, 5.27, 0.07, 4.72, 0.45mg/L, respectively. Four hours later than the initial runoff, the concentration was changed to 1.00, 0.94, 4.06, 0.01, 0.60, 0.33 mg/L, respectively. As a result of artificial irrigation, three out of four sediment traps were filled with runoff water from the experimental plots. One sediment trap was not filled with runoff water because the artificial irrigation was not supplied for two experimental plots. The stage of sediment traps were gradually lowered. However, the water quality didn't showed a decrease trend as the stage went down because the suspended solid was not equally collected during the water sampling.

• Journal of Computing Science and Engineering
• /
• v.6 no.2
• /
• pp.119-126
• /
• 2012

Machine-to-machine communications for healthcare is emerging for the benefit of humans. In addition to novel medium access, we provide a systematic view to look for ways to develop technology to accomplish this goal, and a thorough vision toward effective system and network design.

• Bulletin of the Korean Mathematical Society
• /
• v.47 no.5
• /
• pp.933-950
• /
• 2010

We study a relationship between sets of uniqueness, weakly sufficient sets and sampling sets in the space $A^{-{\infty}}(\mathbb{B})$ of holomorphic functions with polynomial growth on the unit ball of $\mathbb{C}^n$ ($n\;{\geq}\;1$).