• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.690-700
• /
• 1998

Rubber-toughened particles which are used in the field of chemical engineering are used to increase the fracture toughness of thermoset resin. The application of Core-Shell particles, one of rubber-toughened particles, as a filler for dental composite or restoration have not been examined. The purpose of this study was to evaluate possible use of Core-Shell particles for dental composite, and the hypothesis was that additional toughening mechanisms are activated by the addition of Core-Shell particles. After blending 50vol% quartz with Bis-GMA/TEGDMA resin matrix, the experimental resins were made by the addition of Core-Shell particles with varied content level as 0, 2.5, 5, 7.5, 10, 12.5, 15, and 20wt%. Fracture toughness was determined on three-point bending specimen with single-edge notch according to ASTM-E 399. Also, flexural properties, that is, strength and modulus were measured by three-point bending testing. Fractogragh of fracture toughness specimen was observed using SEM (JEOL 6400 SEM, MA). The following results from this study were obtained ; 1. Fracture toughness of composite resin added 2.5wt% Core-Shell particles was significantly higher than control group ($p{\leq}0.05$). 2. Flexural properties were decreased with increasing Core-Shell particle content, which showed a correlation statistically ($p{\leq}0.05$). 3. A toughening mechanism such as lamination and microcrack was observed in specimen determined high fracture toughness. 4. The dispersion of Core-Shell itself and quartz filler particles was limited present high content of Core-Shell particles, which decreased a resulting mechanical properties of composites. These results suggest that adequate Core-Shell particles can be used to enhance mechanical properties included toughening for dental composites.

• 치과방사선
• /
• 제14권1호
• /
• pp.81-87
• /
• 1984

This study was performed to observe the secondary images and to analyse the relationships between the primary and secondary images in panoramic radiograph. Using the Moritta's Panex-EC panoramic x-ray machine and the human dry skull, the author analysed 17 radiographs which were selected from 65 radiographs of the dry skull that attached the radiopaque materials, and the attached regions of the radiopaque materials were the normal anatomical structures which were important and selected as a regions for the evaluation of the secondary images effectively. The results were as follows; 1. The cervical vertebrae showed three images. The midline image was the most distorted and less clear, and bilateral images were slightly superimposed over the posterior border of the mandibular ramus. 2. In mandible, the secondary image of the posterior border of the ramus was superimposed on the opposite ramus region, and this image was elongated from the anterior border of the ramus to the lateral side of the posterior border of the ramus. The secondary image of the condyle was observed on the upper area of the coronoid process, the sigmoid notch and the condyle in opposite side. 3. In maxilla, the posterior region of the hard palate showed the secondary image on the lower part of the nasal cavity and the medial wall of the maxillary sinus. 4. The primary images of the occipital condyle and the mastoid process appeared on the same region, and only the secondary image of the occipital condyle was observed symmetrically on the opposite side with similar shape to the primary one. 5. In the cranial base, the anatomical structures of the midsagittal portions like a inferior border of the frontal sinus, sella turcica, inferior borderr of the sphenoid sinus and inferior border of the posterior part of the occipital bone showed the simillar shape between the primary and secondary images symmetrically. 6. The petrous portion of the temporal bone showed the secondary image on the lateral side of the sella-turcica, and the secondary images of the posterior border of lesser wing, superior border of greater wing of the sphenoid bone and posterior border were observed on the anterior-superior and inferior region of the sella-turcica.

• 한국농공학회지
• /
• 제18권4호
• /
• pp.4209-4217
• /
• 1976

The purpose of this thesis is to search for the determination method of pumping rates in the existing tube wells for irrigation. Pumping tests were carried out for the twelve test tube wells which were selected in the provinces of Kyounggi, Kangwon, Chungbuk and Chungnam. The depths, static water levels, pumping levels, drawdowns and yields of tube wells were measured in the pumping tests, and a centrifugal pump with 3 inches diameter, a 5 HP motor and a 90$^{\circ}$ V-notch were used in the pumping tests. The average coefficient of transmissibility calculated by Chow's and Jacob's methods is 0.0336 square meter per second, and the average pumping rate calculated by Thiem's, Smreker's, Brinkhaus' and Theis' formulae, is 919 cubic meter per day, Therefore, the ground water storage in the test areas is comparatively abundant. Correlation between pumping rates and depths of tube wells is not in existence. Also, correlation between pumping rates and the thickness of aquifer is not found in this experiment. This shows that the depths of some tube wells are deep and their thicknesses of aquifer are thick, but their ground water storages are poor, and that the depths of some tube wells are shallow and their thicknesses of aquifer are thin, but their ground water storages are abundant. It seems that the test tube wells are influenced by the peculiar characteristics that the ground water in the test areas is free ground water in alluvium layer closely related with surface water. As drawdown increases, pumping rate decreases, and as the coefficient of transmissibility increases, pumping rate also increases. Namely, there are negative correlation between pumping rate and drawdown, and positive correlation between pumping rate and the coefficient of transmissibility. Judging from the results of the pumping tests in these tests areas, the pumping rate calculated by the formula, {{{{ { Q}_{m } =Q { ( { { S}_{ m} } over { TRIANGLE S } )}^{ { 2} over {3 } } }}}} used traditionally, is likely to be higher than real pumping rates. The formula, {{{{ { Q}_{m } =Q { { H}^{ 2} } over { (2H- TRIANGLE S) TRIANGLE S} }}}} derived from Thiem's theory, is looked upon as the reasonable one to detemine pumping rates in the existing tube wells for irrigation.

• The Korean Journal of Physiology
• /
• 제20권2호
• /
• pp.165-174
• /
• 1986

The voltage clamp studies were undertaken to elucidate the properties of the slow inward current, $i_{si}$, in the small preparations of the rabbit sinoatrial node. The slow inward current, $i_{si}$, which is known to be responsible for the late one-third of pacemaker potential and whole range of upstroke phase of action potential was analysed with the effects of isoprenaline, cobalt, ouabain and higenamine. The results obtained are as follows; 1) Voltage of SA node preparation was held at zero current level, usually-40mV and the slow inward current, $i_{si}$, was activated by depolarizing clamp pulses. Peak values of $i_{si}$, in steady state were at $-10{\pm}0mV$ in most preparations. 2) Isoprenaline, ${\beta}-agonist$ increased $i_{si}$ and no shift was noticed in voltage-dependency. 3) Cobalt ion in the concentration of 1 mM abolished is, in entire range of membrane potential and the difference of two current levels before and after $Co^{2+}$ treatment could be considered as pure $i_{si}$ magnitude. 4) In the therapeutic concentration of ouabain $(5{\times}10^{-8}M)$ slightly increased is, and reduced the time to reach the peak value. 5) Higenamine $(10^{-6}M)$ changed the configurations of action potential (i. e. rapid upstroke phase and notch in the spike) and increase spontaneous rate. It also increased is, and the effect of higenamine was blocked ${\beta}-blocker$, propranolol $(10^{-6}M)$.

• 대한토목학회논문집
• /
• 제7권2호
• /
• pp.59-68
• /
• 1987

본(本) 논문(論文)에서는 콘크리트의 파괴실험을 통하여 파괴거동을 규명하고 파괴에너지를 결정하였으며, 이로부터 파괴에너지 예측공식을 도출하였다. 콘크리트의 파괴실험은 3 점휨하중실험을 수행하였으며 초기균열길이에 따른 파괴거동과 파괴에너지의 변화특성을 규명하기 위하여 초기균열길이를 보깊이의 각각 0, 0.2, 0.4, 0.6 배로 하였다. 본 실험으로부터 하중-처짐곡선이 자동으로 기록되었으며, 이 하중-처짐곡선하의 면적이 콘크리트의 파괴에너지를 결정하기 위하여 이용되었다. 본 연구에서 도출된 파괴에너지 예측공식은 콘크리트구조물의 파괴해석을 위해 효과적으로 이용될 수 있으며, 파괴에너지가 콘크리트의 인장강도와 골재크기에 의존하고 있음을 나타내고 있다. 또한, 본 연구에서는 콘크리트보의 최대하중을 계산하기 위하여 소위 등가균열길이 개념용 고안하였으며, 이를 위하여 등가균열길이에 대한 예측공식을 제안하였다. 본 등가균열길이 개념은 R-curve 등(等)에 의하지 않고도 파괴하중을 계산할 수 있는 효과적인 개념으로 분석되고 있다.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.343-348
• /
• 2007

Alumina/silver nanocomposites were fabricated using a soaking method through a sol-gel route to construct an intra-type nanostructure. The pulse electric-current sintering (PECS) technique was used to sinter the nanocomposites. Several specimens were annealed after sintering. The microstructure, mechanical properties, critical frontal process zone (FPZ) size, and thermo-mechanical properties of the nanocomposites were estimated. The relative densities of the specimens sintered at 1350 and $1450^{\circ}C$ were 95% and 99%, respectively. The maximum value of the three-point bending strength was found to be 780 MPa for the $2{\times}2{\times}10 mm$ specimen sintered at $1350^{\circ}C$. The fracture toughness of the specimen sintered at $1350^{\circ}C$ was measured to be $3.60 MPa{\cdot}m^{1/2}$ using the single-edge V-notched beam (SEVNB) technique. The fracture mode of the nanocomposites was transgranular, in contrast to the intergranular mode of monolithic alumina. The fracture morphology suggested that dislocations were generated around the silver nanoparticles dispersed within the alumina matrix. The specimens sintered at $1350^{\circ}C$ were annealed at $800^{\circ}C$ for 5 min, following which the maximum fracture strength became 810 MPa and the fracture toughness improved to $4.21 MPam^{1/2}$. The critical FPZ size was the largest for the specimen annealed at $800^{\circ}C$ for 5 min. Thermal conductivity of the alumina/silver nanocomposites sintered at $1350^{\circ}C$ was 38 W/mK at room temperature, which was higher than the value obtained with the law of mixture.

• 한국강구조학회 논문집
• /
• 제23권4호
• /
• pp.483-491
• /
• 2011

본 연구에서는 구조용강재의 샤르피 충격시험(Charpy Impact Test)을 통해 저온에서의 충격 인성(Impact Toughness) 평가를 실시하여 사용 가능 온도를 파악함으로써 강재의 극한지 적용성을 검토하였다. 본 시험에 사용된 강재는 용접구조용강 중 현재 가장 널리 쓰이는 강종인 SM490B와 TMCP (Thermo-Mechanical Control Process)법에 의해 제조된 고강도 강재인 SM570-TMC이다. 또한, 본 시험결과와의 비교를 위해 남극 세종기지 건설시 사용실적이 있는 일반구조용강인 SS400에 대해서도 시험을 수행하였다. 대부분의 강구조물은 용접에 의해 제작되므로, 강재의 극한지 적용성 검토를 위해 용접시험판을 제작하여 모재(Base Metal), 용접금속(Weld Metal) 및 열양향부(Heat Affected Zone)에 대해서 충격시험을 실시하였다. 단, SS400의 경우에는 용접구조용강재가 아니므로 모재에 대해서 충격시험을 실시하였다. 대상 강재의 샤르피 충격시험을 통해서 저온에서의 충격흡수에너지 값을 구하고 이를 강재의 항복응력에 따른 충격흡수에너지의 기준값과 비교함으로써 강재의 사용온도를 결정하였으며, 이를 통해서 구조용강재의 극한지 적용성을 검토하였다.

• Archives of Plastic Surgery
• /
• 제38권4호
• /
• pp.485-489
• /
• 2011

Purpose: Median cleft of upper lip is defined as any congenital vertical cleft through the midline of the upper lip. It is uncommon, its embryological pathogenesis remains unexplained to date. The authors hereby report a rare case of median cleft of the upper lip associated with enlarged frenulum and palatal mass. This case offers some understanding of the possible embryologic development of this anomaly. Methods: A 10-month-old boy born by normal vaginal delivery at full-term had a notch in the midline of the upper lip with widened philtrum along with enlarged median frenulum, alveolar cleft, and mass of the hard palate. We performed en bloc resection of the enlarged frenulum and palatal mass and cheiloplasty under general anesthesia. Results: Histological examination revealed that the frenulum and palatal mass was consisted of fibrous tissue with normal mucous membrane. The postoperative course was satisfactory. Conclusion: A rare case of median cleft of the upper lip with associated enlarged frenulum and palatal mass was presented with proper surgical management. The surgical technique includes marginal excision of the clefted epithelium and reconstruction of orbicularis oris muscle, in addition to en bloc resection of the palatal mass and frenulotomy.

• 비파괴검사학회지
• /
• 제24권4호
• /
• pp.307-314
• /
• 2004

배관의 축방향 균열 검사를 위하여 원주 방향으로 진행하는 유도초음파 모드를 적용하였다. 배관의 곡률을 변수로 원주 유도초음파의 분산선도를 계산하였으며 이를 배관 검사에 적용하기 위하여 중수로 피더관의 곡관부 축방향 균열을 탐지에 적용하였다. 상대적으로 낮은 주파수에서는 Lamb 파 특성을 따르나 주파수가 증가함에 따라 평판의 경우, 즉 곡률이 무한대인 경우 첫 번째 $A_0$ 모드와 두 번째 $S_0$ 모드가 합쳐져서 Rayleigh 모드 형태로 변화한다. 한편 곡률을 가진 배관의 경우는 주파수가 증가하더라도 첫 번째 모드와 두 번째 모드가 합쳐지지 않았다. 이러한 해석을 기초로 하여 배관의 일종인 중수로 피더관 곡관부 축방향 결함을 탐지하기 위하여 사각 탐촉자를 사용하여 Rocking 원주 유도초음파 기법을 적용하였다. 원주 방향으로 유도파를 진행시키면서 인공 결함으로부터의 수집된 신호를 분석하여 진동 모드를 확인하였으며 두께 대비 10% 깊이의 notch도 검출할 수 있음을 확인할 수 있었다.

• 비파괴검사학회지
• /
• 제28권4호
• /
• pp.352-357
• /
• 2008

구조물의 안전 보장 문제에 있어 재료의 파손 이전에 미세균열을 검출하는 것은 매우 중요하다. 비선형 초음파 기법은 일반적인 초음파 기법보다 미세결함에 민감하기 때문에 이를 이용하여 비파괴적으로 구조물이나 재료의 건전성을 진단하는 방법이 주목받고 있다. 계면접촉에 의한 비선형 초음파 효과는 초음파가 내부의 미세 균열에 입사될 때 미세균열면에서 응력과 변위가 비선형 관계를 가지고, 이에 의해 파가 왜곡되어 그 결과 고조파 성분이 발생하는 현상이다. 본 연구에서는 이러한 비선형 초음파 기법의 적용가능성을 알루미늄 시편에 인위적으로 발생시킨 피로균열을 대상으로 실험적으로 검증하고자 하였다. 이를 위해 V-노치를 갖는 A16061의 피로균열 시험편을 준비하고, 균열방향으로 2차 고조파 성분의 크기를 측정하였다. 실험결과 미세균열에서 고조파 성분이 크게 발생하며 이 기법에 의한 균열깊이 측정이 일반적인 반사파의 6 dB drop법보다 정확함을 확인하였다.