• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.4
• /
• pp.109-119
• /
• 2000

PVDF film sensor was applied to measure the stress concentration for monitoring the structural integrity. The strain calibration of this film sensor was performed by the bending test of aluminum beam. The PVDF sensor and the electrical strain gage were bonded on the beam. When the beam was loaded, the output of electrical strain gage was compared with the output of the PVDF sensor. The waveform of PVDF sensor output was shown as the same form of the output of electrical strain gage. The gain was determined as 1.7 by comparing these two signals to determine the exact value of the strain. In order to experiment the stress concentration, the stress field was analyzed by finite element analysis. The tensile test of notched steel specimens was conducted to develop the measurement technique of stress concentration. The output voltage ratio between the PVDF sensor near the notch and the PVDF sensor far from the notch could give the information about the load bearing capacity of steel specimen.

• Steel and Composite Structures
• /
• v.1 no.4
• /
• pp.411-426
• /
• 2001

This paper treats the failure analysis of prestressing steel wires with different kinds of localised damage in the form of a surface defect (crack or notch) or as a mechanical action (transverse loads). From the microscopical point of view, the micromechanisms of fracture are shear dimples (associated with localised plasticity) in the case of the transverse loads and cleavage-like (related to a weakest-link fracture micromechanism) in the case of cracked wires. In the notched geometries the microscopic modes of fracture range from the ductile micro-void coalescence to the brittle cleavage, depending on the stress triaxiality in the vicinity of the notch tip. From the macroscopical point of view, fracture criteria are proposed as design criteria in damage tolerance analyses. The transverse load situation is solved by using an upper bound theorem of limit analysis in plasticity. The case of the cracked wire may be treated using fracture criteria in the framework of linear elastic fracture mechanics on the basis of a previous finite element computation of the stress intensity factor in the cracked cylinder. Notched geometries require the use of elastic-plastic fracture mechanics and numerical analysis of the stress-strain state at the failure situation. A fracture criterion is formulated on the basis of the critical value of the effective or equivalent stress in the Von Mises sense.

• The Korean Journal of Physiology and Pharmacology
• /
• v.23 no.4
• /
• pp.251-261
• /
• 2019

Allergic asthma, is a common chronic inflammatory disease of the airway presenting with airway hyperresponsiveness and airway remodelling. T helper cells-derived cytokines are critically associated with asthma pathogenesis. Janus kinase-signal transduction and activation of transcription (JAK/STAT) signaling is found to be involved in asthma. Magnolol is a plant-derived bioactive compound with several pharmacological effects. The study aimed to assess the effects of magnolol in ovalbumin (OVA)-induced asthmatic model. BALB/c mice were sensitized and challenged with OVA. Magnolol (12.5, 25, or 50 mg/kg body weight) was administered to separate groups of animals. Dexamethasone was used as the positive control. Cellular infiltration into the bronchoalveolar lavage fluid (BALF) were reduced on magnolol treatment. The levels of Th2 and Th17 cytokines were reduced with noticeably raised levels of interferon gamma. Lung function was improved effectively along with restoration of bronchial tissue architecture. OVA-specific immunoglobulin E levels in serum and BALF were decreased by magnolol. Magnolol reduced Th17 cell population and effectively modulated the JAK-STAT and Notch 1 signaling. The results suggest the promising use of magnolol in therapy for allergic asthma.

• Journal of Korean Neurosurgical Society
• /
• v.58 no.3
• /
• pp.236-241
• /
• 2015

Objective : We report on the technical feasibility and limitations of the transmanubrial approach for cervicothoracic junction (CTJ) lesions and emphasize the advantage of bisecting the upper part of the manubrium in an inverted Y-shape. Methods : Thirteen patients who underwent the fourteen transmanubrial approach for various CTJ lesions were enrolled during 2005-2014. For the evaluation of the accessibility for the CTJ lesion, we analyzed the two parallel line defined as a straight line parallel to the inferior and superior plateau of the upper and lower healthy vertebrae, the angle of the two parallel lines and the distance from the sternal notch to lines at the sternum on preoperative magnetic resonance images. Surgical limitations and perspectives, as well as postoperative clinical outcomes were evaluated retrospectively. Results : The CTJ lesions were six metastases, three primary bone tumors, two herniated discs, and one each of a traumatic dislocation with syrinx formation and tuberculous spondylitis and ossification of the posterior longitudinal ligament. If two parallel lines pass below the sternal notch, the manubriotomy should be inevitably performed. The mean preoperative Visual analogue scale score was 8 (range, 5-10), which improved to 4 (range, 0-6) postoperatively. Seven cases showed an increase in Frankel score postoperatively. Conclusion : The spatial relationship between the sternal notch and the two parallel lines to the lesion was rational to determine the feasibility of manubriotomy. The transmanubrial approach for CTJ lesions can achieve favorable clinical outcomes by providing direct decompression of lesion and effective reconstruction.

• Journal of Periodontal and Implant Science
• /
• v.24 no.1
• /
• pp.51-63
• /
• 1994

There has been many attempts to develop a method that can regenerate periodontal tissues that were lost due to periodontal diseasd, but none of them was completely successful. This study was designed to investigate the healing and regeneration of periodontal tissue when bone substitutes such as porous replamineform hydroxyapatite and porous resorbable calcium carbonate were used in combination with oxidized cellulose membrane and collagen absorbable hemostat, compared to a control where only oxidized cellulose membrane or collagen absorbable hemostat were used. Chronic periodontitis was induced on mandibular premolars of and adult dog by placing orthodontic elastic ligatures for 10 weeks. After flap operation, the control group were received oxidized cellulose membrane (control- I )or collagen absorbable hemostat (control- II) only, while one experimental group was given either porous replamineform hydroxyapatite or porous resorbable calcium carbonate in addition to oxidized cellulose membrane (Experimental I-A, I-B), and another experimental group was treated by using either porous replamineform hydroxyapatite or porous resorbable calcium carbonate in addition to collagen absorbable hemostat. (Experimental II-A, II-B) After 56 weeks, healing was histologically analyzed with the following results. 1. Apical migration of junctional epithelium was observed only in areas coronal to the notch for both control and experimental group. 2. Inflammatory cell infiltration was not observed in any groups. 3. Oxidized cellulose membrane and collagen absorbable hemostat were completely resorbed. 4. Newly-formed cementum was observed up to the level where junctional epithelium was located, for both control and experimental groups. 5. Bone formation was limited of the middle portion of the notch in the control group, where as experimental groups showed bone formation up to the level of implant materials coronal to the notch. 6. Minute resorption of apically located portions of implanted materials was observed in experimental group I-B and II-B only.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.6
• /
• pp.541-548
• /
• 2009

In this study, Charpy impact test and numerical studies were performed to examine the effects of failure behavior and energy absorption on the notch position. For this purpose, carbon steel plate(SA-516 Gr. 70) with thickness of 25mm usually used for pressure vessel was welded by SMAW(Shielded Metal-Arc Welding)method and specimens were fabricated from the welded plate. The Charpy impact tests were then performed with specimens having different notch positions varying within HAZ. A series of three-dimensional FE analysis which simulates the Charpy test and crack propagation are carried out as well. We divided HAZ into two, three and four regions to apply mechanical properties of HAZ to FE-analys. Results reveal that the absorbed energies during impact test depend significantly on the notch position. To obtain the results of reliability, HAZ should be divided into at least three regions.

• Advances in concrete construction
• /
• v.13 no.1
• /
• pp.83-99
• /
• 2022

The two, NBD and SCB tests using gypsum circular discs each containing a single notch have been experimentally accomplished in a rock mechanics laboratory. These specimens have also been numerically modelled by a two-dimensional particle flow which is based on Discrete Element Method (DEM). Each testing specimen had a thickness of 5 cm with 10 cm in diameter. The specimens' lengths varied as 2, 3, and 4 cm; and the specimens' notch angles varied as 0°, 45° and 90°. Similar semi-circular gypsum specimens were also prepared each contained one edge notch with angles 0° or 45°. The uniaxial testing machine was used to perform the experimental tests for both NBD and SCB gypsum specimens. At the same time, the numerical simulation of these tests were performed by PFC2D. The experimental results showed that the failure mechanism of rocks is mainly affected by the orientations of joints with respect to the loading directions. The failure mechanism and fracturing patterns of the gypsum specimens are directly related to the final failure loading. It has been shown that the number of induced tensile cracks showing the specimens' tensile behavior, and increases by decreasing the length and angle of joints. It should be noted that the fracture toughness of rocks' specimens obtained by NBD tests was higher than that of the SCB tests. The fracture toughness of rocks usually increases with the increasing of joints' angles but increasing the joints' lengths do not change the fracture toughness. The numerical solutions and the experimental results for both NDB and SCB tests give nearly similar fracture patterns during the loading process.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.311-322
• /
• 1998

American Society for Testing and Materials (ASTM) standard test method PS 070-97 has been created for measuring fracture toughness of advanced ceramics. PS 070-97 includes three test methods which use beams in bending: chevron notch (CNB), single-edged precracked beam (SEPB), and surface crack in flexure (SCF). Supporting data has been collected through several Versailles Advanced Materials and Standards round robins. This paper discusses the evolution of the standard including the rationale for the choice of the three methods and the specifications in the standard. Progress on Standard Reference material 2100 which will have certified values of fracture toughness is presented.

• Journal of Periodontal and Implant Science
• /
• v.24 no.1
• /
• pp.87-97
• /
• 1994

The ultimate goal of periodontal therapy is to fully reconstruct the periodontal attachment apparatus. Commonly used techniques for treatment of infrabony defects include a combination of root planing, curettage and root treatment. To prevent the apical migration of epithelial cells, the technique of guided tissue regeneration is used. The aim of this study is to compare the effects of root treatment with Citric acid & Tetracycline and Guided tissue regeneration in dogs. Experimental periodontitis was induced by the ligation of orthodontic elastic threads in the upper right and left premolars 3, 4 of five adult dogs for 6 weeks. 4 types of procedures were performed as follows; 1) Control graup : Mucoperiosteal flap 2) Experinental I : GTR used Gore-tex(R) membrane 3) Experinental II : Root treatment with citric acid (PHl) 4) Experinental III : Root treatment with tetracycline HCl (50mg/ml) There after, dogs were serially sacrificed at the 1, 2, 4, 5, 8 weeks, and the specimens were prepared, and stained with hematoxylin-eosin for the light microscopic evaluation. The results of this study were as follows; 1. Junctional epithelium reached to the notch through the furcation area in control group at 8 weeks. 2. In the aspects of the inflammatory cell infiltration, control group showed severe aggregation than experimental group I, II, III through the experimental period 3. New cementum was observed over the notch from 5 weeks in experimental group II 4. In the aspects of the amount of new bone formation, experimental group was better than control group, but there was not significant differences among the experimental group, I, II, III

• Journal of Power System Engineering
• /
• v.6 no.3
• /
• pp.24-30
• /
• 2002

The deformation and fracture behaviors of both Al2O3 and Ni 4.5wt.%Al plasma thermal spray coating were investigated by an acoustic emission method. Plasma thermal spray coating is formed by a process in which melted particles flying with high speed towards substrate, then crash and spread on the substrate surface cooled and solidified in a very short time, stacking of the particles makes coating. A tensile test is conducted on notch specimens in a stress range below the elastic limit of substrate. A bendind test is done on smooth specimens. The waveforms of AE generated from the both test coating specimens can be classified by FFT analysis into two types which low frequency(type I) and high frequency(type II). The type I waveform is considered to corresponds exfoliation of coating layers and type II waveform corresponds the plastic deformation of notch tip. The fracture of the coating layers can estimate by AE event and amplitude, because AE features increase when the deformation generates.