• 한국수자원학회논문집
• /
• 제48권1호
• /
• pp.9-21
• /
• 2015

본 연구는 소옥천 호소화 수역의 퇴적물 깊이별 오염도를 조사하고, 표층 퇴적토양을 대상으로 인 용출특성을 실험한 것이다. 퇴적물의 총인 농도는 전 구간에서 대청호 준설 환경기준 1.5mg/g을 초과하였고, T-N은 팔당호 준설기준 1.1 mg/g은 초과하였으나 대청호 준설기준 3.0mg/g보다는 낮게 나타났다. 준설구역은 소옥천 추소수역(WS-6~WS-12)이 적절하다고 판단하였다. 퇴적물 깊이별 오염도 조사 결과 강열감량은 깊이에 따라 낮아지는 경향을 보였고, 총질소는 깊이에 따른 농도 분포 패턴은 나타나지 않았다. 총인 역시 지점과 깊이별로 농도 변이가 적고 특별한 경향성을 보이지 않았다. 소옥천 호저 퇴적물에서 총인의 용출률은 혐기성 조건에서 $7.2{\sim}15.4mg/m^2/d$, 호기성 조건에서는 $0.5{\sim}2.0mg/m^2/d$, 통기성 조건에서는 $2.0{\sim}4.1mg/m^2/d$의 범위로 산정되었다. 혐기성 조건에서 퇴적 표토층의 총인 농도와 용출률의 관계는 결정계수($R^2$)가 0.7871로 나타나 정상관성을 보이고 있다. 또 반응조의 용존산소 농도와 총인 용출률의 관계는 결정계수($R^2$)가 0.8824인 높은 역상관성을 보였다. 퇴적물의 오염도와 반응조건에 따라 용출률이 크게 다르다는 것을 알 수 있었으며, 추소수역에 대한 수중 용존산소 농도 및 퇴적 표토층의 총인 함량과 총인 용출률과의 관계를 해석하였다.

• 항공우주기술
• /
• 제1권2호
• /
• pp.45-50
• /
• 2002

본 논문에서는 지상 관제국과 2005SAT 위성 사이에서 RF 신호로써 명령 및 원격측정 데이터를 전달하는 기능을 수행하는 원격측정명령계 RF 서브시스템의 개념설계 단계의 링크버짓 해석을 수행하였다. 링크버짓 성능분석을 위해 업링크 및 다운링크 과정으로 나누고 업링크에 대해서는 위성체에서 전력흐름밀도 및 명령수신기에서 여유를 계산하고 다운링크에 대해서는 다운링크 EIRP 및 지상국에서 C/ $N_o$ 및 $E_b$/ $N_o$ 여유를 계산하여 전체적인 통신성능 여유를 만족하는지 조사를 하였다. 업링크 링크버짓 분석결과 명령수신기에서 충분한 전력 수신 여유가 있었으며 다운링크 링크버짓 분석결과 지상국에서 C/ No 및 $E_b$/ $N_o$의 여유가 적정함을 확인하였다.

• Ocean and Polar Research
• /
• 제44권4호
• /
• pp.297-310
• /
• 2022

To understand the chemical composition of aerosols in the Cheju-Korea Straits and their contribution to the ocean by deposition, aerosol samples were collected on board R/V Eardo from November 1997 to May 1999. The average concentrations of Al, NO₃^-, non-sea-salt (nss)-SO₄^2-, and NH₄⁺ in aerosols were 2.19, 5.59, 6.16 and 2.08 ㎍ m^-3, respectively. The Al concentration in the high yellow dust period was about 100 times higher than that in the non-yellow dust period. The concentration ratio of NO₃^-/nss-SO₄^2- ranged between 0.47 and 1.5, indicating that the aerosols in the Cheju-Korea Straits are under the effects of NO_x and SO_x emitted from China, Korea and Japan. The equivalent concentration ratio of [NH₄⁺]/[nss-SO₄^2-+ NO₃^-] with the average of 0.58±0.29 indicates that nss-SO₄^2- and NO₃^- are not neutralized by NH₄⁺. A high activity concentration of ²¹⁰Pb with 1.13-1.23 mBq m^-3 was observed during the high yellow dust period, indicating that ²¹⁰Pb is easily adsorbed in the yellow dust originating from the continent of Asia. The distribution of ⁷Be and NH₄⁺ concentrations showed a strong negative linear correlation during the low yellow dust period, April 1998. The total mineral dust flux in the Cheju-Korea Straits was estimated to be 1.21×10⁶ tons yr^-1, accounting for about 12% of the annual sediment discharge via the Nakdong River. The combined annual deposition of NH₄⁺ and NO₃^- was 0.103 mole N m^-2 yr^-1 was estimated to support 4% of the annual primary productivity in the East China Sea.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제7권5호
• /
• pp.295-302
• /
• 2002

To understand the utilization property of light energy, Synechococcus sp. MA19, a poly-${\beta}$-hydroxybutyrate (PHB) producer, was cultivated at the different incident light intensities of 15.3, 50.0 and 78.2 W/$m^2$ using media with and without phosphate. From the results of metabolic flux analysis, it was found that the cell yield based on ATP synthesis was estimated as $3.5{\times}10^{-3}$ kg-biomass/mol-ATP in these cultures. Under the examined conditions, there were no significant differences in the efficiency of light energy conversion to chemical energies estimated as ATP synthesis and reducing potential (NADH + NADPH) formation whether the PHB synthesis took place or not. The energy converted from light to ATP was kept relatively high around the energy absorbed by the cells of $2.5-3.0{\times}10^{6} J\;h^{-1}\;kg^{-1}$, whereas the energy of reducing potential was hardly changed in the examined range of the energy absorbed by the cells.

• 수산해양교육연구
• /
• 제14권2호
• /
• pp.177-190
• /
• 2002

An experimental study was carried out to make clear heat transfer characteristics in flow boiling of binary mixtures of refrigerants R134a and R123 in a uniformly heated horizontal tube. Experiments were run at a pressure of 0.6 MPa both for pure fluids and mixtures in the ranges of heat flux $10{\sim}50{kW/m}^2$, vapor quality 0~100% and mass flux 150-600 $kg/m^2s$. Heat transfer coefficients of mixtures were reduced compared to the interpolated values between pure fluids both in the low quality region where the nucleate boiling is dominant and in the high quality region where the convective evaporation is dominant. Total pressure drop during two-phase flow boiling in a horizontal tube consists of the sum of two components, that is, the frictional pressure drop and pressure drop due to acceleration. The frictional pressure drop is the most difficult component to predict, and makes the most important contribution to the total pressure drop. On the other hand, the acceleration pressure drop resulting from the variation of the momentum flux caused by phase change is generally small as compared to the frictional pressure drop. There is no significant difference in measured pressure drop between mixtures and pure fluids. The correlation of Martinelli and Nelson predicted most of the present data both for pure and mixed refrigerants within 30%.

• 한국화재소방학회논문지
• /
• 제23권2호
• /
• pp.111-116
• /
• 2009

시중에 유통되는 17종의 방염 도료를 소방법에서 요구하는 성능에 맞게 MDF에 방염처리하여 화재시 발생되는 복사열에 노출시켰을 경우 어느 정도의 화재지연 효과가 있는지를 연구하였다. 복사열의 크기는 콘히터를 이용하여 $10kW/m^2$에서 $30kW/m^2$까지 변화시키며 실험하였다. 착화시간과 착화형태를 측정하였으며 시료 표면의 온도를 측정하였다. 실험 결과 방염도료를 처리한 시료의 착화 임계열유속은 $10kW/m^2$ 였으며 $30kW/m^2$에서는 방염에 의한 착화지연효과가 없음을 확인할 수 있었다. 또한 시료 표면온도가 $400^{\circ}C$ 이상이 되어도 방염에 의한 화재 억재효과를 기대하기 어렵게 됨을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제14권2호
• /
• pp.529-534
• /
• 2013

식물공장을 위한 회전형 조명 시스템은 기존의 식물공장 조명시스템에 무수히 많이 설치되는 LED를 대신하여 비교적 적은 양의 LED가 설치된 조명장치를 회전시켜 작물들에게 필요한 광을 공급하는 시스템이며, 기존 식물공장 조명시스템에서 발생되는 고가의 초기 설치비용을 해결하기 위한 시스템이다. 본 논문에서는 식물이 생장하는데 필요한 광합성유효광양자속(PPF)에 대하여 조사하고, 회전형 조명시스템 시제품과 광양자센서를 이용하여 조명시스템의 LED출력과 회전속도 변화에 따른 PPF의 차이를 비교, 분석하였다. 블레이드의 회전속도가 20rpm이고 LED의 출력이 IN 73%, CENTER 37%, OUT 50%일 때 모든 영역에서 $200{\mu}mol{\cdot}m^{^-2}{\cdot}s^{^-1}$의 일정한 PPF값이 공급된다는 결과를 확인하였으며, 기존의 식물공장의 조명 시스템에 비해 적은양의 LED를 회전시킴으로써 식물의 성장에 필요한 광을 제공하는데 어려움이 없다는 결과를 확인하였다.

• 전기학회논문지
• /
• 제60권5호
• /
• pp.1073-1077
• /
• 2011

The breaking capacity of circuit breakers could be no more increased in the electric power system. This is because the fault current increases due to continuous increases in electric power demand and facilities. To solve the problem, it is necessary to come up with an alternative. The superconducting fault current limiter (SFCL) has received an attention among various alternatives. The SFCL effectively reduce a fault current in cooperation with a power circuit breaker. A various types of the SFCL are suggested and a study on them have been progressed. As a result of it, the SFCL can be applyed to the electric power system in the near future. But, a study on recovery behaviors of the SFCL is not enough for applying to the electric power system. If the superconducting elements do not completely recover to the superconducting state after fault operation, it might be a breakdown of the superconducting elements due to heavy power burden and it gives an bad influence on the working of other electric devices. Additionally, the distribution power system has reclosing operation such as open-0.3sec-closed/open-3min-closed/open procedure. So we need to study more about improvement of the recovery behaviors of the SFCL. In this paper, we analyzed the recovery behaviors of a flux-coupling type SFCL according to reclosing operation when a single line-to-ground fault occurred and we compared recovery behaviors of the SFCL with and without a neutral line between secondary reactors and superconducting elements. Also, the flux-coupling type SFCL has advantageous for increases of capacity by controlling the variation in turn ratios between two reactors. Consequently, when the number of turns of the secondary reactors increased, the power burden of the superconducting elements was bigger due to the increase of impedances of the secondary reactors. To distribute the power burden, two superconducting elements connected in series and the balanced quenching of the superconducting elements was induced by connecting a neutral line.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.355-360
• /
• 2002

ElectroSlag Strip Overlaying (ESSO) process has been around since 1970. ESSO process had limited acceptance due to a few problems associated with the use of this process in its very early stage. Limited knowledge and, most significantly, poor quality of the equipment and welding flux gave the ESSO process a bad name. However, this process is well accepted today and used in North America, Europe and Japan. The ESSO process provides low dilution overlays at high deposition rates, excellent and consistent deposit chemistry with excellent surface quality, and virtually no defects. Capitan has taken this process one step further through extensive research and development of the process itself as well as the equipment. The improvement brought to the process warranted the issuance in May 2000 of an US patent. This study demonstrates the feasibility of this process with immediate positive production results. The main achievements of this work are as follows: $\textbullet$ Development of six various strip-flux combinations on three different base materials: carbon steel, $\frac{1}{4}$ Cr/.5 Mo and 2 $\frac{1}{4}$ Cr/l Mo, fully tested with: penetrant, ultrasound, bends, hardness, overlay chemistry, corrosion and hydrogen disbonding. $\textbullet$ 12" dia. 90 hot formed elbows from straight pipe electroslag overlayed with "1 layer" and "2 layer" Alloy 625 $\textbullet$ a very unique development of miniaturized overlaying equipment able to perform overlay in pipe with diameters as low as 10" (254 mm). This development has large applications in the field of offshore, petrochemical, refining, pulp and paper and power generation industries. The aftermath of this development was its immediate acceptance by major end users with the completion of four projects of overlayed pipe in the USA and Far East Asia.

• 한국분무공학회지
• /
• 제16권4호
• /
• pp.176-185
• /
• 2011

The empirical correlations for the prediction of penetration height of liquid jet in crossflow are reviewed and classified in this study. Around thirty different correlations had been proposed by many investigators. It has generally known that the penetration height of a liquid jet in a cross-flow is a function of the liquid to air momentum flux ratio and the normalized downstream distance from the injector. However, several researchers incorporated the Weber number, liquid-to-water or air viscosity ratio, pressure ratio or Reynolds number, temperature ratio in the empirical correlations. The existing correlations can be grouped as correlations in a power-law, logarithmic, and exponential forms, respectively. Correlations in a power-law form can be further classified as three groups such as basic form, Weber number form and other parameters form. It should be pointed out that correlations in a logarithmic form in terms of Weber number or any other parameters could not be found. Universal correlation has still not been established due to the significant discrepancies between various correlations suggested to date. Several of the studies reported the significant discrepancies of predicted values by the existing correlations. The possible reasons for discrepancies will be summarized as measurement technique, assumptions made in defining terms in the liquid to air momentum flux ratio, difficulties in defining the boundaries of the liquid jets, and nozzle/injector geometry. Evaluation of validity for the correlations proposed recently by several investigators is essentially required. Those include eight power-law forms, two logarithmic forms, and one exponential form.