• Journal of Sensor Science and Technology
• /
• v.10 no.5
• /
• pp.279-285
• /
• 2001

The capnograph system for determining the partial pressure of carbon dioxide in the blood of a patient was developed based on the NDIR(non-dispersive infrared) absorption technology. NDIR gas analyzing method requires an optical absorption chamber and signal processing hardware. In this paper, we have designed and implemented NDIR type $CO_2$ gas chamber in consideration of the time response characteristics and lamp chopping frequency. And we have implemented signal processing hardware using two infrared sources to reduce the thermal background effect. The implemented gas chamber and signal processing hardware were tested in the temperature variation experiment and human expiratory experiment. The results showed that the system could produce a stable output signal and a good $CO_2$ gas concentration curve like a typical capnogram.

• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.331-336
• /
• 2021

The Non-dispersive Infrared (NDIR) gas sensor has high selectivity, measurement reliability, and long lifespan. Thus, even though the NDIR gas sensor is expensive, it is still widely used for carbon dioxide (CO₂) detection. In this study, to reduce the cost of the NDIR CO₂ gas sensor, we proposed the new optical waveguide structure design based on ready-made gas pipes that can improve the sensitivity by increasing the initial light intensity. The new optical waveguide design is a structure in which a part of the optical waveguide filter is inclined to increase the transmittance of the filter, and a parabolic mirror is installed at the rear end of the filter to focus the infrared rays passing through the filter to the detector. In order to examine the output characteristics of the new optical waveguide structure design, optical simulation was performed for two types of IR-source. As a result, the new optical waveguide structure can improve the sensitivity of the NDIR CO₂ gas sensor by making the infrared rays perpendicular to the filter, increasing the filter transmittance.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.385-390
• /
• 2006

A fast response $CO_2$ analyzer has been developed to study transient characteristics on an SI engine. The analyzer has the delay time of 4.5 ms and time constant of 2.8 ms, which is fast enough to measure $CO_2$ concentration on a transient condition. Wide range of A/F(Air/Fuel) ratio can be estimated using the analyzer with an additional switch type oxygen sensor. The results of measurement of $CO_2$ concentration and A/F ratio on a transient condition including rapid acceleration/deceleration and EGR(Ehxaust Gas Recirculation) on/off are presented and compared with a commercial exhaust gas analyzer and UEGO(Universial Exhaust Gas Oxyzen) sensor.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.497-499
• /
• 2002

This paper proposes the effective compensation method fur the IR lamp deterioration in NDIR capnograph system. The newly designed optical chamber with two IR lamps and an electronic hardware for controlling lamp intensity have been implemented. After applying the proposed optical chamber and reference lamp control circuit to the NDIR type capnograph system, it is identified that the proposed method can compensate the lamp deterioration effectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.628-634
• /
• 2005

We have simulated and proposed novel optical cavity, which has two elliptical mirrors, for NDIR gas sensor module and have tested it from 0 ppm to 2,000 ppm $CO_2$ concentration. The proposed sensor module shows the maximum peak voltage at 500 ms pulse modulation time, however, it shows a maximum voltage changes at 200 ms pulse duration with 18,000 times amplification gain. From 0 ppm to 2,000 ppm, the voltage difference of sensor module $({\Delta}V)$ shows 360 mV at 200 ms pulse duration and 3 sec turn-off time. The response time of designed sensor module is about 30 seconds.

• Journal of Auto-vehicle Safety Association
• /
• v.7 no.2
• /
• pp.39-43
• /
• 2015

NDIR (Non-dispersive infrared Rays) alcohol sensor has been prototyped and its temperature characteristics were measured. In order to design novel optical alcohol sensor, elliptical structures with one common foci were modeled and analyzed their optical properties. After analyzing elliptic optical structures, a prototype alcohol sensor module was tested according to the temperature variations from $-20^{\circ}C$ to $35^{\circ}C$. The offset voltages of alcohol sensor decreased from 1.1056 V at the temperature $-20^{\circ}C$ to 0.7339 V at $35^{\circ}C$. However, the highest sensitivity of alcohol sensor showed about $303{\mu}V/ppm$ at room temperature.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1641-1642
• /
• 2006

본 연구에서는 NDIR(non dispersive infrared absorption) 가스센서의 소형화와 저가화를 목표로 2개의 오목 거울을 이용한 새로운 광 공동(optical cavity) 구조를 제안하고, 구조에 따른 광 출력 특성을 시뮬레이션하였다. Optical cavity는 광 경로증가 및 광 집속 구조로 설계하고, 각각의 출력단에서 검출되는 광 출력을 시뮬레이션한 결과 광 집속 구조의 팡 출력이 더 효율적임을 확인하였다. 집광구조에서의 광 출력을 최대로 하기 위해 광의 초점을 찾아보았다. 집광 구조를 사용하지 않는 단순 평행 광이 조사되는 경우, 적외선 센서부에 입사되는 광 출력은 최대 0.024W이다. 그러나 집광구조에서는 optical cavity의 광축에서 센서의 위치를 $15\sim20mm$까지 변화시켜 시뮬레이션한 결과 거리 18.83mm 일 때 조사되는 광 출력이 약 0.153W로 약 7배 증가됨을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.81-82
• /
• 2005

본 논문에서는 두 개의 오목 반사경으로 형성된 광 공동 구조의 비문산 적외선 (NDIR) 가스센서를 제작하였다. 증폭비는 18,000 배, 램프 off 시간은 3초로 일정하게 하고 펄스 modulation 시간을 200ms에서 600ms까지 변화시켰을 때. 300ms에서 가장 효율적인 출력신호를 확보할 수 있었다. 그리고 $5^{\circ}C$에서 $45^{\circ}C$까지 $10^{\circ}C$ 간격으로 온도를 변화시키면서 이산화탄소의 농도를 0ppm에서 2000ppm까지 증가시켰다. 이때, 약 400mV의 전압변화가 있었다. 온도가 상승함에 따라 0ppm에서의 출력전압은 감소하는 양상을 나타내었다. 또한 온도변화 대비 출력특성과의 상관성 해석을 통하여 온도 보상 방법을 고안하였으며, 본 연구에서 제작한 센서모듈의 응답시간은 약 30초였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1606-1612
• /
• 2015

In this paper, a portable high efficiency nondispersive infrared(NDIR) $CO_2$ sensor module with a smart device interface is developed. For low power consumption design, an IR LED was used instead of tungsten lamp for light source and an optical waveguide optimized to the sensor module is designed. With the smart device interface, power of the sensor module is applied from the battery of smart phone. The measured data of the sensor module such as $CO_2$ concentration, temperature, and humidity are displayed on the smart phone using android application. From measured results, the developed sensor module shows ${\pm}60ppm$ tolerance error from 0 to 3,000ppm $CO_2$ concentration range among $-10^{\circ}C$ and $50^{\circ}C$ ranges.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.3
• /
• pp.398-405
• /
• 2003

A fast response analyzer for measuring carbon dioxide concentration has been developed for transient characteristic and researches tested on internal combustion engine. The analyzer uses the well known NDIR(Non-Dispersive Infrared) method with miniaturized detection system, giving a time constant of approximately 30 microsecond, and sampling module consists of capillary tube. Since the transit time and the time constant of the sampling system depend on the sampling conditions, it is necessary to investigate the characteristics of sampling system before applied to exhaust gas measurement in engine. A unique method was designed to study the influence of the diameter of transfer sample line and operating conditions of the FRNDIR on transit time and time constant. A database of transit time and time constant was built up for different measured and simulated pressure conditions. The database can be used for correcting eventual $CO_2$ concentration measurement.