• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1063-1069
• /
• 1997

For me1t-spun Fe-Nd-C alloys, variation of phase development and magnetic properties with the variety of alloy compositions and production conditions were investigated. To find out whether hard magnetic $Fe_{14}Nd_2C$ is crystallized direct1y from the melt by rapid quenching, the phase development of the as-spun ribbons spun at various speed was a1so studied. For the ribbons spun at 10m/s, ${\alpha}-Fe$ was the primary crystallization phase followed by the secondary $Fe_{17}Nd_2C$. At 20m/s ${\alpha}-Fe$ was suppressed so that the primary $Fe_{17}Nd_2C$ coexisted with the secondary ${\alpha}-Fe$ and the amorphous phase. Above 30m/s the ribbons were a1most amorphous, and the amorphization was complete at 40m/s. $Fe_{14}Nd_2C$ therefore was not found in as-spun state but obtained after heat treating the ribbons. The effective temperature range ($700{\sim}900^{\circ}C$) in which $Fe_{14}Nd_2C$ can be obtained was wider than that of a cast alloy. An alloy made with the wheel speed of 20 or 30m/s yielded higher coercivities after heat treatment. In iron-rich Fe-Nd-C, the composition range in which a high coercivity (more than 10kOe) is expected is narrow, i.e., 77~78 Fe and 7~8 C(at.%).

• Journal of the Korean Magnetics Society
• /
• v.12 no.1
• /
• pp.34-40
• /
• 2002

In order to improve the microstructure of the strip cast Nd-Fe-B alloys that are frequently used for production of high energy sintered magnets, influence of various strip casting conditions on the microstructure and phase formation and distribution were investigated. Nd-Fe-B strips consisting of microstructures suitable for preparation of high energy sintered magnets could be obtained when the wheel speed was below 5 m/s. The compositional limit that can avoid the crystallization of free iron in the as-cast state was estimated to be Nd$\_$14/Fe$\_$79/B$\_$7/. Regardless of the compositional variation, <001> preferred orientation of Nd$_2$Fe$\_$14/B normal to the strip surface was always occurred below 5 m/s, which would eventually enhance the grain alignment during pressing the powder under a magnetic field. While the coercivity of the strip cast alloys increased with the increase of the wheel speed, mainly due to the refinement of Nd$_2$Fe$\_$14/B grains, it decreased with the reduction of Nd content in the alloy composition as the formation of free iron increased.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.122-125
• /
• 1994

The magnetic properties of Nd-Fe-B alloys of containing 4 at.% Nd have been studied for the development of new type rare-earth magnets. The amorphous phase of a melt-spun $Nd_{4}Fe_{85.5}B_{10.5}$ alloy is transformed into the phases which have a small amount of $Nd_{2}Fe_{14}B_{1}$ in ${\alpha}-Fe$ matrix by annealing above their crystallization temperature. The addition of Mo, Nb, V or Cu to $Nd_{4}Fe_{85.5}B_{10.5}$ alloy results in the reduction of grain size and the sub¬sequent improvement of the coercivity. The coercivity of $Nd_{4}Fe_{82}B_{10}M_{3}Cu_{1}$(M = Mo, Nb, V) alloys increases in the order of M = V < Nb < Mo and shows the highest value of 2.7 kOe when M = Mo. On the other hand, the rem¬anence of these alloys shows the opposite trend and the rn>st improved value of 1.35 T is observed when M = V.

• Korean Journal of Food Science and Technology
• /
• v.36 no.6
• /
• pp.872-878
• /
• 2004

Food products selected based on their annual sales and international acrylamide research data were analyzed for quantitation of acrylamide. Samples including raw food, substitute meal, snack, drink, and sauce products were analyzed by LC/MS/MS methods adopted by PDA. Upon comparison, concentrations of acrylamide in these products were similar to those analyzed in other countries.

• Analytical Science and Technology
• /
• v.8 no.3
• /
• pp.351-358
• /
• 1995

Oxidation behavior on the surface of Nd-Fe-B ribbon alloy has been studied by X-ray Photoelectron Spectroscopy. In the incipient stage of oxidation on the surface of "as-received" ribbon Nd-oxide film was formed from the fast oxidation of Nd and Fe was metal state in bulk. In process of oxidation time Fe was more abundant in the outmost surface of ribbon from the defused Fe through Nd-oxide film and layer structure of oxidation film was formed.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.237-241
• /
• 2000

The structural, electrical and etching characteristics of Al alloy thin film with low impurity concentrations AlNd deposited by using do magnetron sputtering deposition are investigated for the applications as gate bus line in the TFt-LCD panel. And ITO thin film was deposited on AlNd, then the contact resistance was measured by Kelvin resistor. The deposited thin films show the decrease of resistivity and the increase of grain size after the RTA at $300^{\circ}C$ for 20 min. Moreover, the resistivity of AlNd does not show appreciable grain size dependence after RTA. It is concluded that the decrease of resistivity after RTA is due to the increase of grain size. The annealed AlNd is found to be hillock free. The etching profiles of AlNd was good and the minimun contact resistance was about $110\;{\mu\Omega}cm$. Calculation results reveal that the AlNd (2wt.%) thin film can be applicable to 25" SXGA class TFT-LCD panels.

• Journal of the Korean Magnetics Society
• /
• v.9 no.3
• /
• pp.154-158
• /
• 1999

Magnetic properties and microstructure of nanocrystalline $\alpha$-(Fe, Co)-based Nd-(Fe, Co)-B-Nb-Cu alloys have been investigated. $Nd_x(Fe_{0.9}Co_{0.1})_{90-x}B_6Nb_3Cu_1$(x=2, 3, 4, 5, 6) alloys prepared by rapid solidification process show amorphous phase except the one with x=2. By a proper annealing, the amorphous in the alloy is changed to a nanocrystalline phase. It is confirmed that the nanocrystalline alloys are composed of $\alpha$-(Fe, Co) and $Nd_2(Fe, Co)_{14}B_1$ phase. The optimally annealed $Nd_3(Fe_{0.9}Co_{0.1})_87B_6Nb_3Cu_1$ alloy shows the highest remanence of 1.55 T. The coercivity increases with the increase of Nd content The maximum coercivity of 4.6 kOe is obtained from an optimally annealed $Nd_6(Fe_{0.9}Co_{0.1})_84B_6Nb_3Cu_1$ alloy, resulting in the maximum energy product of 10.6 MGOe.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.977-980
• /
• 2002

Using the micro-pulling down method, $Nd_2O_3$ doped crack-free stoichiometric $LiNbO_3$ single crystals were grown in 1 mm diameter and 30∼35 mm length. The homogeneous distributions of $Nd_2O_3$ concentration were confirmed by the electron probe micro analysis. The absorption and photoluminescence spectra were measured with respect to the $Nd_2O_3$ doping.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.18-23
• /
• 2011

Sintered Nd-Fe-B magnets are widely used in many fields such as motors, generators, actuators, microwaves and so on due to their excellent magnetic properties. Many researchers have shown that the Nd-rich phase was essentially important for high magnet properties. In this study, we focused on controlling of the Nd-rich phase to enhance magnetic properties by the cyclic sintering process. Nd-Fe-B based sintered magnets were prepared by isothermal sintering and cyclic sintering processes. Magnetic properties and microstructure of the magnets were investigated. The coercivity was enhanced from 21.2 kOe to 23.27 kOe after 10 cycles of the sintering. The Nd-rich phase was effectively penetrated into the grain boundary between the $Nd_2Fe_{14}B$ grains by the cyclic sintering.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7B
• /
• pp.403-410
• /
• 2007

Neighbor Discovery (ND) protocol was proposed to discover neighboring hosts and routers in IPv6 wire/wireless local networks. ND protocol, however, has a problem that it is vulnerable to network attacks because ND protocol allows malicious users to impersonate other legitimate hosts or routers by forging ND protocol messages. To address the security problem, Secure Neighbor Discovery (SEND) protocol was proposed. SEND protocol provides address ownership proof mechanism, ND protocol message protection mechanism, reply attack prevention mechanism, and router authentication mechanism to protect ND protocol. In this paper, we design and implement SEND protocol in IPv6 local networks. And also, we evaluate and analyze the security vulnerability and performance of SEND protocol by experimenting the implemented SEND protocol on IPv6 networks.