• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.58-62
• /
• 2001

A numerical investigation was performed to determine the effect of airfoil on the optimum flap. height using NACA 0006, 0009, 0012, 0015, 0018, 0021 and 0024 airfoils. The six flaps which have 0.5% chord height difference were used. A Navier-Stokes code, FLUENT, was used to calculate the flow field of the airfoil. The code was first tested as a benchmark by modelling flow around a NACA 4412 airfoil. Predictions of local pressure coefficients are found to be in good agreement with the result of the experimental result. For every NACA 00XX airfoil, flap heights ranging from 0.0% to 2.5% chord were changed by 0.5% chord interval and their effects were also studied. Representative results from each case are presented graphically and discussed. It is concluded that this initial approach gives a promise for the future development of wind turbine optimum design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.565-574
• /
• 2007

The flow control effect of blending Gurney flap with jet flap for flow around an NACA 0012 airfoil was numerically investigated through parameter variation of each flow control mechanism on unstructured meshes. The aerodynamic force and moment variations due to flow control were examined, and the results were compared between the blending control and each individual flow control. The results showed that the blending control required less energy input to achieve the same level of lift increment than that of the jet flap, and at the same time alleviated drag increment caused by introducing the Gurney flap.

• Journal of Aerospace System Engineering
• /
• v.10 no.4
• /
• pp.11-16
• /
• 2016

In this paper, an experimental study on the aerodynamic characteristics of a variable span wing flying inside a channel guideway is accomplished using wind tunnel testing. A variable span wing with a NACA 0012 airfoil section was fabricated and actuated using a linear servo motor. The aerodynamic effects of 1) wing aspect ratio, 2) ground effect, and 3) the gap between the wingtip and the wing fence were investigated. It was found that both ground effect and wing fence gap increased lift. Also, the wing fence gap does not significantly affect drag. Therefore, it was found that a variable span mechanism can be used as an effective high lift device when flap use is limited.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.12
• /
• pp.1153-1161
• /
• 2010

An efficient solution method for harmonic balance techniques with Fourier transform is presented for periodic unsteady flow problems. The present partially-implicit harmonic balance treats the flux terms implicitly and the harmonic source term is solved explicitly. The convergence of the partially Implicit method is much faster than the explicit Runge-Kutta harmonic balance method. The method does not need to compute the additional flux Jacobian matrix from the implicit harmonic source term. Compared with fully implicit harmonic balance method, this partial approach turns out to have good convergence property. Oscillating flows over NACA0012 airfoil are considered to verify the method and to compare with results of explicit R-K(Runge-Kutta) and dual time stepping methods.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.337-345
• /
• 2008

this study, three dimensional surface pressure distributions of SWIM whose main wing has NACA4412 airfoil with NACA0012 flaps were experimentally measured by pressure sensitive paint. Surface pressures on suction and pressure sides of the wing were measured by changing an angle of attack at a Reynolds number of 3.1x105 in KARI 1m subsonic wind tunnel. The experimental results showed that as an angle of attack increases minimum pressure region on a suction side moved from the wing root to the tip and low pressure region around trailing edge of the wing tip which causes wing tip vortex was observed. Although low pressure region at the tip still observed at an angle of attack 15 deg., other area on a suction side showed flat pressure distribution in a span-wise direction. It was also observed that the mean value of pressure coefficients was about 0.077 through a comparison between PSP and pressure taps at the same test conditions.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.491-496
• /
• 2000

The objective of this study is to increase lift and decrease drag of an airfoil by delaying flow separation with piezo-ceramic actuators. The airfoil used is NACA 0012 and the chord length is 30cm. An experiment is performed at the freestream velocity of 15m/s at which the Reynolds number is $3{\times}10^5$. Seven rectangular actuators are attached to the airfoil surface and move up and down based on the electric signal. At the attack angle of $16^{\circ}$, the separation point is delayed downstream due to momentum addition induced by the movement of the actuators. Drag and lift are measured using an in-house 2-dimensional load cell and the surface pressures are also measured. Lift is increased by 10%, drag is reduced by 50%, and the efficiency is increased to 170%. The flow fields with and without control are visualized using the smoke-wire and tuft techniques.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.544-549
• /
• 2014

임계마하수보다 큰 자유흐름 마하수에서는 충격파의 발생으로 인해 급격한 항력증가가 발생하므로, 임계마하수 증가는 고속 공기역학에서 중요한 분야로 다뤄지고 있다. Whitcomb R. T.에 의해 천음속영역에서 순항할 수 있는 초임계익형이 개발되었으나, 충격파 제어 기법들에 대한 실험적인 검증은 형상 제작의 어려움으로 인해 한계를 지닌다. 따라서 본 논문에서는 2D_Comp-2.1_P와 Prandtl-Glauert 압축성 보정식을 이용하여 NACA0012와 RAE2822의 임계마하수를 해석하고, 충격파 제어 장치 중 하나인 Bump를 RAE2822에 설치하여 임계마하수를 향상시키기 위한 연구를 수행하였다. 연구 결과 충격파를 압축파로 분산시켜 충격파의 강도를 약화시키고, 양항비의 4.7% 증가를 확인하였다. 따라서 Bump를 설계한 RAE2822가 기본 익형보다 높은 천음속 조건에서 효율적인 공력특성을 가지는 것을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.5
• /
• pp.685-694
• /
• 2002

Effects of wake-passing orientation and frequency on the wake-induced boundary layer transition on a NACA0012 airfoil are investigated. The wakes are generated by rotating cylinders clockwise (CW) and counterclockwise (CCW) around the airfoil. Time- and phase-averaged streamwise mean velocities and turbulent fluctuations are measured with a single hot-wire probe. Wall skin frictions are estimated by the Computational Preston Tube Method (CPM). The pressure distribution on the airfoil is different according to the wake-passing orientation and frequency. Turbulent patches are generated in the laminar boundary layer due to the passing wake and the boundary layer becomes temporarily transitional. The transition process is significantly affected by the pressure gradient and the turbulent patches. For the receding wake, the turbulent patches propagate more rapidly than those for the approaching wake because adverse pressure gradient becomes larger. As the frequency increases, onset location of transition moles upstream and the boundary layer near the trailing edge becomes more transitional.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.776-785
• /
• 2001

Hot-wire measurements are performed in boundary layers developing on a NACA0012 airfoil over which wakes pass periodically. The Reynolds number based on chord length of the airfoil is 2$\times$10(sup)5 and the wakes are generated by circular cylinders rotating clockwise and counterclockwise around the airfoil. This paper and its companion Part II describe the phenomena of wake-induced transition of the boundary layers on the airfoil using measured data; phase-and time-averaged streamwise mean velocities, turbulent fluctuations, integral parameters and wall skin frictions. This paper describes the background and facility together with results of time-averaged quantities. Due to the passing wake with mean velocity defects and high turbulence intensities, the laminar boundary layer is periodically disturbed at the upstream station and becomes steady-state transitional boundary layer at the downstream station. The velocity defect in the passing wake changes the local pressure at the leading of the airfoil, significantly affects the time-mean pressure distribution on the airfoil and eventually, has influence on the transition process of the boundary layer.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.8
• /
• pp.1112-1118
• /
• 2000

The objective of this study is to increase lift and decrease drag of an airfoil at high angles of attack by delaying flow separation with piezo-ceramic actuators. The airfoil used is NACA 0012 and its chord length is 0.3m. An experiment is performed at the freestream velocity of 15m/s at which the Reynolds number based on the chord length is $2{\times}10^5$. Seven rectangular actuators are attached to the airfoil surface and move up and down based on the electric signal. Drag and lift are measured using an in-house two-dimensional force-balance and the surface pressures are also measured. At the attack angle of $16^{\circ}$, the separation point is delayed downstream due to momentum addition induced by the movement of the actuators. Lift is increased by 10%, drag is reduced by 37%, and the efficiency is increased up to 170%. The flow fields with and without control are visualized using the smoke-wire and tuft techniques.