• Journal of Mechanical Science and Technology
• /
• v.20 no.3
• /
• pp.358-365
• /
• 2006

The hydraulic pump of an Electro-hydrostatic Actuator should be able to quickly feed large volume of oil into hydraulic cylinder in order to reduce the response time. On the other hand, it should be also able to precisely dispense small amount of oil through low-speed operation so that the steady state position control error of the actuator can be accurately compensated. Within the scope of axial piston type hydraulic pumps, this paper is focused on the investigation how the surface treatment of their cylinder barrel with TiN plasma coating can contribute to the reduction of the friction and wear rate of valve plate in the low-speed range with mixed lubrication. The results showed that the friction torque of the valve plate mated with a TiN coated cylinder barrel could be reduced to 22% of that with an uncoated original one when load pressure was 300 bar and rotational speed 100 rpm. It means that the torque efficiency of the test pump was expected to increase more than 1.3% under the same working condition. At the same time, the wear rate of the valve plate could be reduced to $40\sim50%$.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.79-87
• /
• 1978

This is an experimental study on friction welding and heat treatment of engine exhaust valve materials whose welding combination is SCr4 as stem to 21-4N as head and SUH3 to 21-4N. In this study, not only the experiments of friction welding under the selected optimum welding condition and the examination of the mechanical properties were carried out, but also the heat treatment of friction welded specimens under the two selected conditions was taken to obtain the better welding character, eliminating the latent stress and the hardness peak which appeared at the welded zones of heat resisting steel(21-4N, SUH3) and low alloyed steel ($SCr_4$) friction weldments. The results obtained by the experiments and consideration in this study are as follows: I) It was experimentally proved quite reasonable that 'speed=3,OOO rpm, heating pressure Pl=8 kg/ mm2, upsetting pressure p, = 20 kg/mm', heating time $t_1$ = 3 see, upsetting time TEX>$t_2$ = 2.5 sec' was selected as the optimum welding condition for friction-welding the engine exhaust valve materials $SCr_4$ to 21-4 Nand SUH 3 to 21-4 N. 2) The results of the previous study and this one on friction welding of such dissimilar materials as SUH 3-SUH 31, SCr 4-SUH 31, SCr 4-SUH 3, SUH 3-CRK 22, SCr4-21-4 Nand SUH3-21-4 N agreed with each other substantially in the friction welding characteristics at welded interface zones. 3) It was also certified quite satisfactory that '600\ulcornerCX30 min. Xroom air cooling' as an optimum heat treatment condition of the friction welded materials SCr 4-21-4 Nand SUH 3-21-4 N was experimentally determined to eliminate the latent stress and the hardness peak at welded zones. 4) About 20% of the tensile strength before heat treatment of friction welded specimens was decreased after heat treatment 600\ulcornerCX30 min. Xair cooling, but the location of fracture was moved from heat affected zone to parent $SCr_4$ & SUH3. 5) Microscopic examination of the weld joints friction-welded and heat-treated under the above mentioned conditions revealed that the weld zone is very narrow and has a fine grained intermixed structure without any welding defects. 6) The above mentioned conditions can be also utilized as friction welding parameters of the other dissimiar materials for engine valve production.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.1
• /
• pp.65-73
• /
• 2014

Objectives: The purposes of this study are to investigate workers' exposures to respirable particles generated in taconite mines and to compare two metric methods for mass concentrations using direct-reading instruments. Methods: Air monitorings were conducted at six mines where subjects have been exposed primarily to particulate matters in crushing, concentrating, and pelletizing processes. Air samples were collected during 4 hours of the entire work shift for similarly exposure groups(SEGs) of nine jobs(N=37). Following instruments were employed to evaluate the workplace: a nanoparticle aerosol monitor(particle size range; 10-1000 nm, unit: ${\mu}m^2/cc$, Model 9000, TSI Inc.); DustTrak air monitors($PM_{10}$, $PM_{2.5}$, unit: $mg/m^3$, Model 8520, TSI Inc.); a condensation particle counter(size range; 20-1000 nm, unit: #/cc, P-Trak 8525, TSI Inc.); and an optical particle counter(particle number by size range $0.3-25{\mu}m$, unit: #/cc, Aerotrak 9306, TSI Inc.). Results: The highest airborne concentration among SEGs was for furnace operator followed by pelletizing maintenance workers in number of particle and surface area, but not in mass concentrations. The geometric means of $PM_{2.5}$ by the DustTrak and the Ptrak/Aerotrak were $0.04{\mu}m$(GSD 2.52) and $0.07{\mu}m$(GSD 2.60), respectively. Also, the geometric means of RPM by the DustTrak and the Ptrak/Aerotrak were $0.16{\mu}m$(GSD 2.24) and $0.32{\mu}m$(GSD 3.24), respectively. The Pearson correlation coefficient for DustTrak $PM_{2.5}$ and Ptrak/Aerotrak $PM_{2.5}$ was 0.56, and that of DustTrak RPM and Ptrak/Aerotrak RPM was 0.65, indicating a moderate positive association between the two sampling methods. Surface area and number concentration were highly correlated($R^2$ = 0.80), while $PM_{2.5}$ and RPM were also statistically correlated each other($R^2$ = 0.79). Conclusions: The results suggest that it is possible to measure airborne particulates by mass concentrations or particle number concentrations using real-time instruments instead of using the DustTrak Aerosol monitor that monitor mass concentrations only.

• Journal of Korean Society of Forest Science
• /
• v.102 no.1
• /
• pp.7-14
• /
• 2013

This study investigated the optimum condition of abrasion peeling machine and pellicle peeling ability of chestnut (Castanea spp.) varieties for the efficient production of peeled chestnuts. The optimum conditions were 50 minutes peeling time and 27 rpm of drum rotation speed and chestnut pellicle peeling ratio was 89.3%. Among 8 Korean chestnut varieties which were peeled under the optimum condition (27 rpm/50 min), 'Tsukuba (89.3%)', 'Tanzawa (72.2%)' and 'Ishizuchi (70.9%)' showed the highest ratio of pellicle peeling ratio. 'Tsukuba' had the most excellent peeled (grade I) chestnuts (77.3%), followed by 'Ishizuchi (46.7%)', and 'Tanzawa (45.0%)'. Regarding the chestnuts quality for commercialization, 'Tsukuba' had the most excellent peeled chestnuts (90.5%), followed by 'Tanzawa (74.8%)', and 'Ishizuchi (74.3%)'. 'Mipung (37.2%)' had the most broken and injured chestnuts and 'Tsukuba (5.9%)' had the least broken and injured chestnuts. Therefore this study concluded that 'Tsukuba' was the superior variety for producing high value-added processed chestnuts.

• Economic and Environmental Geology
• /
• v.43 no.2
• /
• pp.123-136
• /
• 2010

In order to remediate heavy metal contaminated Nong island, Maehyang-ri shooting range soils through the batch reactor scale washing were evaluated. The experiment texture soil of N3 in the Nong island at north side incline was (g)mS containing 12.9% gravel, 47.0% sand, 35.1% silt and 5.0% clay. And the N3 soil area was contaminated with Cd($22.5\pm1.9$ ppm), Cu($35.5\pm4.0$ ppm), Pb($1,279.0\pm5.1$ ppm) and Zn($403.4\pm9.8$ ppm). The EDTA(ethylene diamine tetra acetic acid, $C_{10}H_{16}N_2O_8$) in the N3 soil was observed as most effective extractants among the 5 extractants(citric acid, EDTA, phosphoric acid, potassium phosphate and oxalic acid) tested. And chemical partitioning of heavy metals after washing N3 soil with EDTA was evaluated. Removal efficiency of residual fractions was higher than that of non-residual fractions. To choose EDTA extractant which is the most effective in soil washing technology using batch reactor process cleaning Pb and Zn contaminated sits; Pb and Zn removal rates were investigated 92.4%, 94.0% removal(1,000 mM, soil:solution=5, $20^{\circ}C$, 24 hour shaking, pH=2, 200 RPM), respectively. The results of the batch test showed that the removal efficiency curve was logarithmic in soil was removal. Thus, EDTA washing process can be applied to remediate the Pb and Zn contaminated soil used in this study.

• Microbiology and Biotechnology Letters
• /
• v.21 no.6
• /
• pp.609-614
• /
• 1993

The optimum conditions for the submerged mycelial culture of Lentinus edodes SR-1 were elucidated to be incubation temperature of 25C, initial pH 4.0, agitation of 300 rpm, inoculation of 10.0%(v/v), and aeration of 1.0 v/v/m in TGY medium. The optimum c/n ratio and economic yield coeffcient for the submerged mycelial culture were 13.1:1 and 0.45 respectively. As the plant growth hormones test, SCM medium containing 0.5ppm of 2,4-dicholorophenoxyacetic acid increased mycelial yield in 1.1%, but 6-benzylaminopurine was not effective.

• Journal of Korean Society on Water Environment
• /
• v.22 no.6
• /
• pp.996-1003
• /
• 2006

The absorption characteristics of powdered activated carbon doped by transition-metal nanoparticles were investigated to enhance the remove efficiencies of $TCOD_{Mn}$ and Color from the flexo-inks wastewater. According to the adsorption dynamics of PAC and MPAC, the optimal dosage of activated-carbon adsorbents was 3 g/L under the reaction conditions of pH6.0, 30 mill of reaction time, 240 rpm of mixing intensity. The removal efficiencies by the optimal dosages were maximized as 19% $TCOD_{Mn}$, 57% Color for PAC and 88% $TCOD_{Mn}$, 95% Color for MPAC. Freundlich indexes of isotherm absorption were estimated as follows: i) For PAC, k=-8.11, 1/n=2.98, r=0.91 in the raw water, and k=0.14, b/n=0.75, r=0.96 in the biological treatment water, ii) For MPAC, k=2.69, 1/n=0.21, r=0.80 in the raw water, and k=0.74, 1/n=1.17, r=0.95 in the biological treatment water. MPAC (Powdered activated carbon doped by transition-metal nanoaprticles) was very effective in the removal of organics from the raw water and biological treatment water, as Freundlich indexes of 1/n for both types of water were estimated less than 2.0.

• Microbiology and Biotechnology Letters
• /
• v.8 no.1
• /
• pp.55-60
• /
• 1980

Some of the cultural conditions were improved in order to obtain the higher biomass of Lactobacillus bulgaricus NLS-4 which has the higher lactic acid producing activity as well. Among eight media including 11％ non-fat milk medium as a control, the TIP medium was selected. By a batch experiment, the maximum cell concentration could be increased to 1.0$\times$10$^{9}$ cells per $m\ell$ when the organism was grown at 38$^{\circ}C$ for 18 hours with agitation speea of 200 rpm and under the constant level of pH 6.5 con-trolled with 1 N KOH solution in the selected medium. The cell concentration was further increased to 2.3$\times$10$^{9}$ cells per me in the steady state of continuous culture at the dilution rate of 0.17 hr$^{-1}$ for 18 hours.

• Membrane and Water Treatment
• /
• v.4 no.1
• /
• pp.11-25
• /
• 2013

Emulsion liquid membrane (ELM) process suffers from emulsion instability problem. So far, emulsion produced by mechanical methods such as stirrer and homogenizer has big size and high emulsion breakage. This paper discussed the application of emulsion produced by sonicator to extract cadmium in a batch ELM system. The emulsions consist of N,N-Dioctyl-1-octanamine (trioctylamine/TOA), nitrogen trihydride (ammonia/NH4OH), sorbitan monooleate (Span 80), and kerosene as carrier, stripping solution, emulsifying agent, and organic diluent, respectively. Effects of comprehensive parameters on extraction efficiency of Cd(II) such as emulsification time, extraction time, stirring speed, surfactant concentration, initial feed phase concentration, carrier concentration, volume ratio of the emulsion to feed phase, and pH of initial feed phase were evaluated. The results showed that extraction efficiencies of Cd(II) greater than 98% could be obtained under the following conditions: 15 minutes of emulsification time, 4 wt.% of Span 80 concentration, 4 wt.% of TOA concentration, 15 minutes of extraction time, 250 rpm of stirring speed, 100 ppm of initial feed concentration, volume ratio of emulsion to feed phase of 1:5, and initial feed pH of 1.53.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2002.11b
• /
• pp.53-53
• /
• 2002

Shoot tips of in vitro propagated plantlets were cryopreserved using encapsulation/dehydration procedures. Shoot tips were excised under filter sterilized antioxidants solution (0.2M phosphate buffer, pH 5.7 supplemented with 5g/1 ascorbic acid and 15g/1 sodium borate). They were drawn up into a sterile 10 $\textrm{cm}^3$disposable pipette and were dropped into the culture medium with 2.5w/v Na-alginate, then into 100mM CaCl$_2$.2$H_2O$. Encapsulated shoot tips were transferred into 10㎤ of liquid culture medium with a range of sucrose concentrations (0.25-1.0M) and were incubated in dark for 24 hours in 18C at 40rpm. Beads were then dehydrated in silica gel for different time intervals (1-24 hours). Then they were freeze dried either rapidly (plunge directly into liquid N2 or in two stages (samples were kept at 20C for 10 minutes, then reduced to 35C at 1C per minute. Then, plunge into liquid $N_2$). The influence of sucrose and silica gel pre-treatment on pre- and post-freeze shoot growth was examined.(중략)