• 한국식품영양과학회지
• /
• 제2권1호
• /
• pp.1-21
• /
• 1973

The muscle of abalone, Notohaliotis discus (REEVE), and top-shell, Turbo cornutus Solander, were examined for protein composition. Then paramyosins which are known as one of the important structural protein of the muscle fibrils were isolated from the both muscle and their physico-chemical properties such as solubility, salting-out behaviour, intrinsic viscosity, ATPase activity, etc. involving amino acid composition and N-terminal amino acid residues were investigated to elucidate phylogenie characteristics more intensively from the viewpoint of comparative biochemistry. The analysis of protein composition resulted in the following estimations: abalone muscle; water-soluble protein of 22 %, salt-soluble protein, 34%, alkali-soluble protein, 20%, and stroma protein, 24%, and top-shell muscle; water-soluble protein of 16%, salt-soluble protein, 30%, alkali-soluble protein, 29%, and stroma protein, 25%, respectively. It is demonstrated in sedimentation analysis that paramyosin and myosin-actomyosin account for approximately 65% and 35% of the salt-soluble protein of abalone, and that the composition of both sediments in top-shell was approximately 70% and 30%, respectively. The ultracentrifugally homogenous paramyosins isolated essentially according to Bailey's ethanol-dried method from both of the muscle showed a $S^{\circ}_{20,w}$ of 3. 14s for abalone and a $S^{\circ}_{20,w}$ of 3.50s for top-shell. The both paramyosins were commonly rich in arginine, aspartic acid, and glutamic acid, while scarcely contained proline and tryptophan, in rough accord with the other paramyosins thus far reported. It is clear that these gastropod paramyosins showed of having the characteristic N-terminal amino acid residues such as N-aspartic acid, N-valine, N-serine, and N-threonine in common. The abalone paramyosin completely salted in with KCl beyond $0.35{\mu}$ and the top-shell paramyosin beyond $0.30{\mu}$. The abalone paramyosin was salted-out between 18% and 30% saturation of ammonium sulphate and the top-shell paramyosin between 22% and 29% saturation. The intrinsic viscosities at abalone and top-shell paramyosins at $25^{\circ}C$ were estimated respectively to be 3.1 dl/g and 2.6 dl/g showing somewhat higher than the values for some other paramyosins from lamellibranchs. In regard with the ATPase activity, the para myosin specimens did not exhibit any significant activity over through the pH conditions of 5 to 9.5. irrespective of the presence of $Ca^{++}$ or $Mg^{++}$. So was the case with the abalone paramyosin prepared by a slightly modified Bailey's wet-extraction method.

• 한국해양학회지:바다
• /
• 제11권3호
• /
• pp.117-123
• /
• 2006

유기물 증가원인의 파악과 근본적인 대책에 대한 연구의 일환으로 부영양화된 연안해역에 대하여 태풍 발생 전후의 수질변동에 대하여 조사하였다. 용존산소 포화도는 수온과 염분 약층이 형성된 시기에 저층에서 54%이하로 관측되었다. 태풍이 지나간 직후에는 표층과 저층에서 거의 비슷한 용존산소 포화도$(78\sim88%)$가 조사되었다. 그리고, 태풍이 지나간 3일 후 식물플랑크톤이 대량으로 증식한 표층에서 용존산소 포화도가 234%로 아주 높은 값이 관측되었고, 저층(5m)에서도 90%가 조사되었다. 염분이 가장 낮았던 시기에 표층에서 $NH_4-N,\;NO_3-N,\;SiO_2-Si$의 최고 농도가 각각 18.22, 38.90, $52.10{\mu}M$로 조사되었으며, $NH_4-N,\;PO_4-P,\;SiO_2-Si$는 용존산소가 낮은 저층에서도 높게 나타났다. 클로로필은 최고 $311.0{\mu}g^{-1}$가 태풍 후에 관측되었으며, 그 원인 생물은 Scrippsiella trochoidea(42,000 cells $ml^{-1}$)였다. 조류성장잠재능력은 태풍발생 후에 아주 높게 조사되었으며, 항상 질소가 부족한 것으로 조사되었다. 화학적 산소요구량은 최고 $10.55mg\;l^{-1}$였으며, 태풍으로 저층 퇴적물로부터 부유되는 유기 오탁 물질이 화학적 산소요구량 증가에 미치는 기여도는 크지 않은 것으로 보이며, 화학적 산소요구량 증가의 대부분이 식물플랑크톤의 증식에 기인한 것($r^2=0.612$, p=0.000)으로 조사되었다.

• 한국생산제조학회지
• /
• 제8권4호
• /
• pp.65-65
• /
• 1999

Heat transfer performance is studied for boiling and condensation of R-11 on integral-fin tubes. Nine tubes with trapezoidal integral-fins having fin densities from 748 to 1654fpm and 10,30 grooves and finned tubes with caves of 0.55 and 0.64 mm height respectively are tested. in case of condensation CFC-11 condensates at saturation stat of 32℃ on the outside surface cooled by inside cooling water flows. And in case of boiling the refrigerant evaporates at a saturation state of 1 bar on the outside tube surface and heat is supplied by hot water which circulates inside of the tube,. The tube having fin transfer coefficient concerns fin tubes with caves show higher valve than low fin tube having find density of 1299fpm and 30grooves. The overall heat transfer coefficient of fin tube with caves is about 5155 W/mK at 2.8m/s of water velocity, The value is abuot 2.7 times higher than plain tube and 1.3 times higher than low fin tube having fin density of 1299fpm and 30 grooves.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.491-495
• /
• 2004

The industries use polymer materials for many purposes for they have many merits. The costs of these materials take up too great a proportion of the overall cost of products that use these materials as their major material. It is advantage for polymer industries to reduce these costs. The microcellular foaming process was developed in the early 1980s to solve this problem and proved to be quite successful. Microcellular foaming process uses inert gases such as $CO_2$, $N_2$. As these gases solve into polymer matrices, many properties are changed. The microcellular foaming process makes the glass transition temperature of polymers to low, and diminish the residual stress of polymer matrices. Besides, the microcellular foaming process has several merits, impact strength elevation, thermal insulation, noise insulation, and raw material saving etc. This characteristic of microcellular foaming process has influenced by cell morphology. The cell morphology means cell size and cell density. The cell morphology has influenced by many factors. The examples of factor are pressure drop rate, foaming temperature, foaming time, saturation pressure, saturation time etc. Among their factors, pressure drop rate is the most important factor for cell morphology in microcellular foaming injection molding process. This paper describes about the cell morphology change in accordance with the pressure drop rate of microcellular foaming injection molding process.

• International Journal of Concrete Structures and Materials
• /
• 제7권3호
• /
• pp.193-202
• /
• 2013

Geopolymer mortar compressed blocks were prepared using fly ash, ground granulated blast furnace slag, silica fume and metakaolin as binders and sand/quarry dust/pond ash as fine aggregate. Alkaline solution was used to activate the source materials for synthesizing the geopolymer mortar. Fresh mortar was used to obtain the compressed blocks. The strength development with reference to different parameters was studied. The different parameters considered were fineness of fly ash, binder components, type of fine aggregate, molarity of alkaline solution, age of specimen, fluid-to-binder ratio, binder-to-aggregate ratio, degree of saturation, etc. The compressed blocks were tested for compression at different ages. It was observed that some of the blocks attained considerable strength within 24 h under ambient conditions. The cardinal aim was to analyze the experimental data generated to formulate a phenomenological model to arrive at the combinations of the ingredients to produce geopolymer blocks to meet the strength development desired at the specified age. The strength data was analyzed within the framework of generalized Abrams' law. It was interesting to note that the law was applicable to the analysis of strength development of partially saturated compressed blocks when the degree of saturation was maintained constant. The validity of phenomenological model was examined with an independent set of experimental data. The blocks can replace the traditional masonry blocks with many advantages.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.420-423
• /
• 1997

The oxygen saturation of blood can be measured by sensing the difference absorption in optical spectra of Hb and $HbO_2$, as the well known previous study. [1] In this study we developed the noninvasive tissue reflectance oximeter(TRO) using three kinds of LEDs which produce a peak spectral emission at a wavelength of 565, 660 and 940nm. And we tested the unction of the TR oximeter by comparing the output signals measured on normal tissue to measured on low oxygenated tissue. The results showed that oxygen saturation of blood and biological tissue can be monitored from the separation arrangement light source and detector.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.875-880
• /
• 2018

This paper proposes a novel combined compensation structure in the infrared receiver chip. For the infrared communication chip, the current-voltage (I-V) convert circuit is crucial and important. The circuit is composed by the transimpedance amplifier (TIA) and the combined compensation structures. The TIA converts the incited photons into photocurrent. In order to amplify the photocurrent and avoid the saturation, the TIA uses the combined compensation circuit. This novel compensation structure has the low frequency compensation and high frequency compensation circuit. The low frequency compensation circuit rejects the low frequency photocurrent in the ambient light preventing the saturation. The high frequency compensation circuit raises the high frequency input impedance preserving the sensitivity to the signal of interest. This circuit was implemented in a $0.6{\mu}m$ BiCMOS process. Simulation of the proposed circuit is carried out in the Cadence software, with the 3V power supply, it achieves a low frequency photocurrent rejection and the gain keeps 109dB ranging from 10nA to $300{\mu}A$. The test result fits the simulation and all the results exploit the validity of the circuit.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.27-35
• /
• 1999

A study was made on the fabrication of nanostructured Fe-Co powders by mechanical alloying and their magnetic properties. Microstrural development during the process of MA was inverstigated by means of X-ray diffraction, differential thermal analyzer, scanning electron microscopy and transmission electron microscopy. The magnetic properties of NS Fe-Co powders were evaluated through the measurements of the saturation magnetization $(M_s)$ as well as the coercivity $(H_c)$. The average grain size calculated from line braodening in XRD peak was about 10nm or less and confirmed by TEM. In this experiment, two different milling methods (cycle opertion and conventional milling) were used. Cycle operation had an advantage over the conventional milling method in that more refined powders can be obtained. Solid state alloying of the components was confirmed from both the change of the saturation magnetization and the change of lattice parameter with Co contentration. Maxium $M_s$ was obtained at the composition of 30at.%Co. Relatively high coercivities of 10~150e were obtained for the compositions investigated, and this seems to be due to the high amount of internal strain introduced during milling.

• 전력전자학회논문지
• /
• 제3권1호
• /
• pp.61-69
• /
• 1998

본 논문은 예측전류제어기의 연산시간에 의한 전압형 PWM 인버터의 과도상태 특성 저하를 개선하기 위한 부분보상 예측전류 제어기에 관한 연구로서, 먼저 부분보상 예측전류제어 시스템에 대한 해석을 통해 과도상태시 정정시간을 최소화할 수 있는 가중치를 구하였다. 또한 부분보상 예측전류제어에 의한 PWM 인버터의 출력전압 포화 경계조건을 유도하여 포화현상이 예측전류제어기의 과도응답 특성에 미치는 영향을 살펴보았다. 끝으로 부분보상 예측전류제어기를 능동전력필터에 적용하여 가중치에 따른 과도응답 특성을 실제전류와 샘플링전류를 중심으로 고찰하였다.

• 한국자기학회지
• /
• 제8권3호
• /
• pp.125-130
• /
• 1998

13Cr-1.5Nb-Fe합금분말이 수분사법으로 제조되엇다. 제조된 합금뷴말을 압축기를 이용하여 ring현상으로 성형한후, 진공중에서 소결하였다. as-prepared 분말의 현상, 입도분포, 성분분석 및 포화자화물 조사하였으며, 소결된 시편의 투자율, 교류자기이력손실이 조사되었다. as-prepared 13Cr-1.5Nb-Fe합금분말의 포화자화는 160emu/g이었으며, 산소함유량은 약 600ppm이었다. 입도분포는 약 70$\mu$m에서 50%vol.을 나타낸다. 교류투자율은 소결온도 및 성형온도가 증가할수록 증가한다. 주파수 20KHz에서 교류자기이력손실은 12ton/cm2성령압력 및 120$0^{\circ}C$ 소결온도 조건에서 107W/cc로 가장우수하다.