• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1802-1812
• /
• 2016

Cross regulation is a key technical issue of single-inductor multiple-output (SIMO) DC-DC converters. This paper investigates the cross regulation in single-inductor dual-output (SIDO) Buck converters with continuous conduction mode (CCM) operation. The expressions of the DC voltage gain, control to the output transfer function, cross regulation transfer function, cross coupled transfer function and impedance transfer function of the converter are presented by the time averaging equivalent circuit approach. A small signal model of a SIDO CCM Buck converter is built to analyze this cross regulation. The laws of cross regulation with respect to various load conditions are investigated. Simulation and experiment results verify the theoretical analysis. This study will be helpful for converter design to reduce the cross regulation. In addition, a control strategy to reduce cross regulation is performed.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2011-2013
• /
• 2001

In this paper the MMAE(Multiple Model Adaptive Estimation) algorithm using the MGEKF(Modified Gain Extended Kalman Filter) of which modes are set to be measurement biases is proposed to enhance the performance of target tracking with bearing only measurements. The state are composed of relative position, relative velocity and taregt acceleration. The mode probability is calculated from the bearing only measurements from the HMS(Hull-Mounted Sonar). The proposed algorithm is tested in a series of computer simulation runs.

• Journal of muscle and joint health
• /
• v.2 no.1
• /
• pp.41-72
• /
• 1995

The purpose of this study is to examine the effects of assertiveness training and value clarification training on nurse's conflict and conflict management mode. Fifty seven registered nurses participated in the study ; they were employed by three general hospital located in Daegu, Korea. The study employs two treatment groups. The assertiveness training group consisted of subjects who participated in 90-120 minutes sessions of assertiveness training nine times over five weeks. The other treatment group, was adiministed nine, 90-120 minutes sessions of value clarification during the same period. For the control group, nursing subjects were appointed the training after five weeks. Pre-test evaluation were administered to all subjects in three groups prior to one week of the treatment. Role conflict Inventory-general(RCI-G) and Communication Conflict Inventory-general (CCI-G) measure nurse's conflict management mode. Post-test evaluation were administered to all subjects in three groups two weeks after the last session by Role Conflict Inventory-Specific(RCI-S), Communication Conflict Inventory-Specific (CCI-S), Management Model-Specific(CMMI-S). The analysis of variance(ANOVA) and covariance(ANCOVA) on gain scores were running the SPSS program. In order to test statistical differences among mean scores of the scales obtained after treatment, multiple comparisons were carried out by Turkey method. Conclusions obtained from the results are as follows. 1. The assertiveness training and the value clarification training were effective in decreasing the nurse's role conflict. The value clarification was more effective than the assertiveness training in decreasing the nurse's role conflict. 2. Both assertiveness training and value clarification training were effective in decreasing nurse's communication conflict. There was, however, no differences between assertiveness training and value clarification training in decreasing the nurse's communication conflict. 3. The assertiveness training and the value clarification training were quite effective in compromizing and collaborating conflict management mode, to reducing the withdrawl and accomodate, force and accomodate conflict management mode to conflict. There was no difference in the effectiveness of assertiveness training and value clarification. In assessing the effects of the treatments, this study employed different measurements. It is unclear whether the measurement affected the test results. It is worth conducting a further test using the same measurements. The results of future studies can be compared with those of this study. The homogeneity of the control group and treatment group is questionable. Futher studies may employ homogeneous sample group to evaluate whether the sample characteristics bias the test results. Assertiveness training or value clarification training for nurses can be utilized in nursing intervention.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.454-459
• /
• 2017

In this study, a thermal system was designed using a 3-way valve and PTC attached to a solar module. This design could help solve the problem of rising fossil fuel costs caused by limited reserves and environmental problems resulting from fossil fuel use. The thermal system is a hot-air and heating control system composed of a temperature sensor part, mode setting part (for hot air and heating modes), supply part, and thermal system control part. The temperature sensor part has piping and an indoor temperature display, and the temperature setting part has multiple monitoring functions. The mode setting part switches between hot air and heating modes and can be used to set the temperature. The thermal system control part performs functions such as PTC control and temperature setting, PTC day and night and time selection, hot air and heating control, and three-way valve selection. The results verify that the system operates with stable response speeds of $680{\mu}s$ in the temperature sensor part, $700{\mu}s$ in the mode setting part, and $610{\mu}s$ in the thermal system control part.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.6
• /
• pp.36-45
• /
• 1998

This paper discusses multiple access control aspects for a wireless extension of high-speed asynchronous transfer mode(ATM) networks. One challenging requirement is that mobile systems convey of diverse types of information including voice, computer data, facsimile, and video data that have different quality of service constraints. Basically, a centralized control scheme for a coordinated multiple access is required in order to efficiently accommodate multimedia traffic on wireless links. The proposed scheme dynamically scheduling the mobile terminal, which has data to transfer according to the service, types at base station. In this scheme, the scheduling algorithm is performed on the basis of traffic descriptors and QoS parameters, which required in the connection set up phase. As a consequence, the transmission scheduling is very flexible and can account for the different traffic rate and delay constraints that emerge from voice and data integration. The simulation result shows that the proposed scheme has better performance over other scheduling algorithms.

• Structural Engineering and Mechanics
• /
• v.29 no.5
• /
• pp.505-530
• /
• 2008

This paper proposes the application of active multiple tuned mass dampers (AMTMD) for translational and torsional response control of a simplified two-degree-of-freedom (2DOF) structure, able to represent the dynamic characteristics of general asymmetric structures, under the ground acceleration. This 2DOF structure is a generalized 2DOF system of an asymmetric structure with predominant translational and torsional responses under earthquake excitations using the mode reduced-order method. Depending on the ratio of the torsional to the translational eigenfrequency, i.e. the torsional to translational frequency ratio (TTFR), of asymmetric structures, the following three cases can be distinguished: (1) torsionally flexible structures (TTFR < 1.0), (2) torsionally intermediate stiff structures (TTFR = 1.0), and (3) torsionally stiff structures (TTFR > 1.0). The even distribution of the AMTMD within the whole width and half width of the asymmetric structure, thus leading to three cases of installing the AMTMD (referred to as the AMTMD of case 1, AMTMD of case 2, AMTMD of case 3, respectively), is taken into account. In the present study, the criterion for searching the optimum parameters of the AMTMD is defined as the minimization of the minimum values of the maximum translational and torsional displacement dynamic magnification factors (DMF) of an asymmetric structure with the AMTMD. The criterion used for assessing the effectiveness of the AMTMD is selected as the ratio of the minimization of the minimum values of the maximum translational and torsional displacement DMF of the asymmetric structure with the AMTMD to the maximum translational and torsional displacement DMF of the asymmetric structure without the AMTMD. By resorting to these two criteria, a careful examination of the effects of the normalized eccentricity ratio (NER) on the effectiveness and robustness of the AMTMD are carried out in the mitigation of both the translational and torsional responses of the asymmetric structure. Likewise, the effectiveness of a single ATMD with the optimum positions is presented and compared with that of the AMTMD.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.15 no.5
• /
• pp.215-225
• /
• 2020

Light detection and ranging (LiDAR) sensors detect the distance of the surrounding environment and objects. Conventional LiDAR sensors require a certain amount of a power because they detect objects by transmitting lasers at a regular interval depending on a constant resolution. The constant power consumption from operating multiple LiDAR sensors is detrimental to autonomous and electric vehicles using battery power. In this paper, we propose two algorithms that improve the inefficient power consumption during the constant operation of LiDAR sensors. LiDAR sensors with algorithms efficiently reduce the power consumption in two ways: (a) controlling the resolution to vary the laser transmission period (T_P) of a laser diode (LD) depending on the vehicle's speed and (b) reducing the static power consumption using a sleep mode depending on the surrounding environment. A proposed LiDAR sensor with a resolution control algorithm reduces the power consumption of the LD by 6.92% to 32.43% depending on the vehicle's speed, compared to the maximum number of laser transmissions (N_x·max). The sleep mode with a surrounding environment-sensing algorithm reduces the power consumption by 61.09%. The proposed LiDAR sensor has a risk factor for 4-cycles that does not detect objects in the sleep mode, but we consider it to be negligible because it immediately switches to an active mode when a change in surrounding conditions occurs. The proposed LiDAR sensor was tested on a commercial processor chip with the algorithm controlling the resolution according to the vehicle's speed and the surrounding environment.

• Journal of Advanced Navigation Technology
• /
• v.19 no.2
• /
• pp.108-115
• /
• 2015

Multilateration systems are used to provide the position of aircraft in flight or on airport runways. In the multilateration systems, the interrogator is an important transmitter that used to interrogate the airplanes with appropriately scenario in surveillance airspace. Whisper-Shout interrogation sequence, which is one of the key functions of the interrogator, can control airport traffic density when intruder airplanes are coming into the surveillance airspace. Therefore collision chance between airplanes could be reduced and also get highly accurate location of incoming airplane in multilateration systems. In this paper, we developed the interrogator that allows it to transmit Mode A/C and Mode S interrogations which is similar to existing secondary surveillance radar. With appropriately controlled Whisper-Shout sequence in the interrogator, the multilateration systems can avoid synchronous garbling and FRUIT phenomenons caused by receiving multiple responses from a number of airplanes.

• Restorative Dentistry and Endodontics
• /
• v.40 no.4
• /
• pp.299-305
• /
• 2015

Objectives: The purpose of this study was to investigate the effectiveness of multiple decontamination procedures for salivary contamination after curing of a universal adhesive on dentin bond strength according to its etch modes. Materials and Methods: Forty-two extracted bovine incisors were trimmed by exposing the labial dentin surfaces and embedded in cylindrical molds. A universal adhesive (All-Bond Universal, Bisco) was used. The teeth were randomly divided into groups according to etch mode and decontamination procedure. The adhesive was applied according to the manufacturer's instructions for a given etch mode. With the exception of the control groups, the cured adhesive was contaminated with saliva for 20 sec. In the self-etch group, the teeth were divided into three groups: control, decontamination with rinsing and drying, and decontamination with rinsing, drying, and adhesive. In the etch-and-rinse group, the teeth were divided into four groups: control, decontamination with rinsing and drying, decontamination with rinsing, drying, and adhesive, and decontamination with rinsing, drying, re-etching, and reapplication of adhesive. A composite resin (Filtek Z350XT, 3M ESPE) was used for filling and was cured on the treated surfaces. Shear bond strength was measured, and failure modes were evaluated. The data were subjected to one-way analysis of variation and Tukey's HSD test. Results: The etch-and-rinse subgroup that was decontaminated by rinse, drying, re-etching, and reapplication of adhesive showed a significantly higher bond strength. Conclusions: When salivary contamination occurs after curing of the universal adhesive, additional etching improves the bond strength to dentin.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.264-272
• /
• 2009

In this paper, a Ka-band 10 W power amplifier module is designed and fabricated using MIC(Microwave Integrated Circuit) module technology which combines multiple power MMIC(Monolithic Microwave Integrated Circuit) chips on a thin film substrate. Modified Wilkinson power dividers/combiners are used for millimeter wave modules and CBFGC-PW-Microstrip transitions are utilized for reducing connection loss and suppressing resonance in the high-gain and high-power modules. The power amplifier module consists of seven MMIC chips and operates in a pulsed mode. for the pulsed mode operation, a gate pulse control circuit supplying the control voltage pulses to MMIC chips is designed and applied. The fabricated power amplifier module shows a power gain of about 58 dB and a saturated output power of 39.6 dBm at a center frequency of the interested frequency band.