• 한국재료학회지
• /
• 제8권11호
• /
• pp.987-992
• /
• 1998

Ti 과 AI의 고순도 원소 박판을 이용하여 열간프레스장치에서 고온자전합성법으로 TiAI계 금속간화합물을 제조하였다. 원소 박판에서 $TiAl_3$ 금속간화합물을 제조하는 데 승온속도, 압력, 온도 등의 변수가 고온자전합성에 영향을 미치는 중요한 인자다. 특히 승온속도는 반응합성온도를 결정하는 인자로서 본 실험에서 DTA 분석을 이용하여 공정변수를 결정하였다. DTA 분석결과에 따르면, Ti와 AI의 계면에서 반응합성은 AI의 용융점 이하와 이상의 온도에서 두 번 발생함을 알 수 있다. 또한 승온속도가 증가할수록 두 반응합성온도는 증가하였다. 10층의 Ti 박판과 9층의 AI 박판을 $20^{\circ}C$/min의 승온속도로 고온자전합성시킨 후, $810^{\circ}C$와 240MPa의 압력에서 4시간 동안 열처리한 결과 $700\mu\textrm{m}$ 두께의 TiAI계 금속간화합물 판재를 제조하였으며, XRD 회절과 SEM으로 확인하였다.

• 한국재료학회지
• /
• 제33권11호
• /
• pp.439-446
• /
• 2023

Changes in the microstructure and mechanical properties of as-roll-bonded AA6061/AA5052/AA1050 three-layered sheet with increasing annealing temperature were investigated in detail. The commercial AA6061, AA5052 and AA1050 sheets with 2 mm thickness were roll-bonded by multi-pass rolling at ambient temperature. The roll-bonded Al sheets were then annealed for 1 h at various temperatures from 200 to 400 ℃. The specimens annealed up to 250 ℃ showed a typical deformation structure where the grains are elongated in the rolling direction in all regions. However, after annealing at 300 ℃, while AA6061 and AA1050 regions still retained the deformation structure, but AA5052 region changed into complete recrystallization. For all the annealed materials, the fraction of high angle grain boundaries was lower than that of low angle grain boundaries. In addition, while the rolling texture of the {110}<112> and {123}<634> components strongly developed in the AA6061 and AA1050 regions, in the AA5052 region the recrystallization texture of the {100}<001> component developed. After annealing at 350 ℃ the recrystallization texture developed in all regions. The as-rolled material exhibited a relatively high tensile strength of 282 MPa and elongation of 18 %. However, the tensile strength decreased and the elongation increased gradually with the increase in annealing temperature. The changes in mechanical properties with increasing annealing temperature were compared with those of other three-layered Al sheets fabricated in previous studies.

• 한국재료학회지
• /
• 제10권9호
• /
• pp.624-628
• /
• 2000

표면 탄성과 디바이스의 전극재료로 사용되는 Al-%Cu(4000$\AA$)/tungsten nitride 박막을 magnetron sputtering 법으로 제조하고 전기저항을 평가한 비정질상의 tungsten nitride 박막을 제조할 수 있었고, 비정질 형성을 위해 질소비(R =$N_2$/(Ar+$N_2$)가 10~40% 정도 필요하다. Tungsten nitride 박막의 잔류응력은 비정질이 형성되면서 급격히 감소되었다. 이러한 비정질 박막위에 Al-1%Cu 합금막이 형성되었다. 다층막은 453K에서 4시간 동안 열처리함으로써 $3.6{\mu}{\Omega}-cm$의 저항을 나타냈는데, 이는 박막내 결정립 성장과 결함의 감소에 기인하였다.

• 한국정밀공학회지
• /
• 제26권7호
• /
• pp.44-50
• /
• 2009

High-pressured jetting is now widely used in the advanced cutting processes of polymers, metals, glass, ceramics and composite materials because of some advantages such as heatless and non-contacting cutting. Similarly to the focused laser beam machining, it is well known as a type of high-density energy processes. High-pressured jetting is going to be developed not only to minimize the cutting line width but also to achieve the short cutting time as soon as possible. However, the interaction behavior between a work piece and high-velocity abrasive particles during the high-pressured jet cutting makes the impact mechanism even more complicated. Conventional high-pressured jetting is still difficult to apply to precision cutting of micro-scaled thin work piece such as thin metal sheets, thin ceramic substrates, thin glass plates and TMM (Thin multi-layered materials). In this paper, we proposed the advanced high-pressured jetting technology by introducing a new abrasives supplying method and investigated the optimal process conditions of the cutting pressure, the cutting velocity and SOD (Standoff distance).

• Advanced Composite Materials
• /
• 제18권2호
• /
• pp.153-166
• /
• 2009

A matrix method for evaluating effective electro-magneto-thermo-elastic properties of a generally anisotropic multilayered composite is presented. Physical variables are categorized into two groups: one that satisfies the continuity across the interface between layers and another that satisfies an average inter-layer compatibility (which is also exact). The coupled electro-magneto-thermo-elastic constitutive equation is accordingly reassembled into submatrices, which leads to the derivation of concise and exact matrix expressions for effective properties of a multilayered composite having the coupled physical effects. Comparing the results for a purely elastic multiplayer with those from other theoretical approaches validates the developed method. Examples are given for a PZT-graphite/epoxy composite and a $BaTiO_3-CoFe_2O_4$ multiplayer which exhibit piezo-thermoelastic and magnetoelectric properties, respectively. The result shows how a strong magnetoelectric effect can be achieved by combining piezoelectric and piezomagnetic materials in a multilayered structure. The magnetoelectric coefficient of the $BaTiO_3-CoFe_2O_4$ multiplayer is compared with those for fibrous and particulate composites fabricated with the same constituents.

• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.29-33
• /
• 2015

This paper presents the results of the optical characteristics of ITO thin film with different buffer layer thicknesses of $SiO_2$ and $Nb_2O_5$ for touch sensor application. $SiO_2$ and $Nb_2O_5$ buffer layers were deposited using RF magnetron sputtering equipment. The buffer layers were inserted between glass and ITO layers. In order to compare with the experimental results, the Essential Macleod Program (EMP) was adopted. Based on EMP simulation, the [$Nb_2O_5{\mid}SiO_2{\mid}ITO$] multi-layered thin film exhibited high transmittance of more than 85% in the visible region. The actual experimental results also showed transmittance of more than 85% in the visible region, indicating that the simulated results were well matched with the experimental results. The sheet resistance of ITO based film was about $340{\Omega}/sq$. The surface roughness maintained a relatively small value within the range of 0.1~0.4 nm when using the $Nb_2O_5$ and $SiO_2$ buffer layers.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.597-598
• /
• 2006

This paper describes a development of a new $1.4{\times}1.1$ and $2.0{\times}1.4mm$ RF SAW filters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.322-322
• /
• 2008

Low-temperature co-fired ceramics (LTCC) have turned out to be very promising technology in accordance with the rapid developments in semiconductor technology. The demands for compact electrical assemblies, smaller power loss as well as high signal density can be fulfilled by LTCC. And for the multi-layered ceramic devices with embedded passive components such as high dielectric constant decoupling capacitor, LTCC materials require the several conditions to avoid delamination and internal cracks. For the present study, diopside-based glass is chosen as the LTCC substrate material in view of its high coefficient of thermal expansion (CTE). From the experimental resultsn the influence of each element on the CTE change can be revealed.

• 한국레이저가공학회지
• /
• 제11권2호
• /
• pp.33-38
• /
• 2008

Laser micromachining has increasingly been adopted in various advanced industries where the high-precision machining of large-area, high-density and multi-layered components is in a strong demand. To effectively meet the requirements, the laser micromachining process must be carefully monitored. In order to facilitate the development of a new laser micromachining process and/or a new system, we have fabricated a UV laser micromachining platform that is equipped with optical modules for monitoring the process online. They include a laser power stabilizing module, a module for laser-induced breakdown spectroscopy, and an auto-focusing module.

• 대한금속재료학회지
• /
• 제49권5호
• /
• pp.380-387
• /
• 2011

Wire brushing, which is a typical surface preparation method for roll bonding, has recently been highlighted as a potentially effective method for surface nanocrystallization. In the present study, the microstructure evolution and hardness of the wire-brushed surface and roll-bonded interface of a 1050 aluminum sheet were investigated. Wire brushing formed protruded layers with a nanocrystalline structure and extremely high surface hardness. After roll bonding, the protruded layers remained as hard layers at the interface. Due to their hardness and brittleness the interface hard layers, can affect the interface bonding properties and also play an important role determining the mechanical properties of multi-layered clad sheets.