• 한국광물학회지
• /
• 제31권3호
• /
• pp.161-172
• /
• 2018

멀티 앤빌 프레스(multi-anvil press)는 일반적으로 5-25 GPa의 압력범위와 ${\sim}2,300^{\circ}C$의 온도범위를 구현할 수 있는 고압 기기로, 지구과학에서는 상부맨틀-맨틀전이대까지의 지구 구성물질의 구조를 연구하는 데 도움이 된다. 본 연구에서는 광물의 상전이를 이용한 멀티 앤빌 프레스에 대한 압력-부하 보정(pressure-load calibration) 과정을 소개하고, 시료실(sample chamber) 내에 존재할 수 있는 온도구배에 대해서 논의하였다. 압력-부하 보정은 14/8 G2, 14/8 step, 14/8 HT 조립세트(assembly set)와 18/12 조립세트에 대해 1,100톤 멀티 앤빌 프레스를 이용하여 수행했다. 초기 물질로 석영, 규회석구조의 $CaGeO_3$, 포르스테라이트를 사용했고, 고압상의 동정은 XRD 분석을 통해 수행하였다. 광물의 상전이를 통해 $1,200^{\circ}C$에서 시료에 가해지는 압력을 유추할 수 있었으며, ${\alpha}$-석영에서 코에사이트로의 상전이는 3.1 GPa, 석류석 구조의 $CaGeO_3$에서 페로브스카이트 구조의 $CaGeO_3$로의 상전이는 5.9 GPa, 코에사이트에서 스티쇼바이트로의 상전이는 9.2 GPa, 포르스테라이트에서 와즐리아이트로의 상전이는 13.6 GPa의 압력 확인에 이용했다. XRD 결과로 획득한 압력-부하 보정 곡선은 기존에 보고된 유사한 기기의 압력-부하 보정 곡선에 비해 동일 압력을 구현하기 위해 50톤 가량의 유압이 더 필요한 것으로 확인됐다. 이러한 차이는 시료실의 크기 및 조립세트의 압력 매체(pressure medium)와 이차앤빌 사이의 마찰력으로부터 기인한 유압 손실에 의한 것으로 생각된다. 또한 본 연구에서는 14/8 HT 조립세트에서의 시료실 내의 온도구배를 확인했다. 특히 열전대(thermocouple)의 위치 변화에 따라 시료실 높이에 평행한 방향으로 약 ${\sim}200^{\circ}C/mm$에 해당하는 온도구배가 존재한다. 본 연구로부터 구한 멀티 앤빌 프레스의 압력-부하 보정 곡선과 시료실 내의 온도구배 값은 앞으로 맨틀 내에서의 다양한 비정질 및 결정질의 지구물질에 대한 원자 구조의 변화와 그에 따른 물성 변화를 설명하는 데 적용할 수 있다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.120-123
• /
• 2004

The bending phenomenon has been known to be occurred by the difference of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets inside die chamber after passing the multi-hole container. The curvature can be controlled by the two variables, the one of them is the different velocity of billets through the multi-hole container, the other is the difference of hole diameter. The bending phenomenon during extruding using four billets can be obtained by the difference of hole diameters in the multi-hole container or by the difference of relative velocity of billet inserted in the container. As results of DEFORM-3D analysis, it can be shown that bending can be obtained during extruding by the difference of relative velocity of two billets or by the difference of hole diameter, and the amount of curvature is increased by the difference of velocity and diameter. According to the shape of products, the curvature of rectangular section is bigger than the curvature of regular square section. And, it is estimated that, because the stress on the welding line is much higher than yield stress of material, the bonding of four billets can be obtained.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.119-122
• /
• 2000

Recently polymer insulators are being used for outdoor high voltage applications. Polymer insulators for transmission line have significant advantages over porcelain and glass insulators, especially for ultra-high voltage transmission lines. Their advantages are light weight, vandalism resistance and hydrophobicity. Polymer insulators are a relatively new technology, but their expected life is still unknown. Therefore these estimating technique are very important. Their life time is related to weathering and operating condition. Multi-aging test is requested because aging factor is occurred by multi-aging than unique aging. The aging test about polymer insulators have mainly carried out by IEC 61109. This paper presents multi-stress chamber experiments and tracking wheel test to examine the tracking and erosion performance of polymer insulator for transmission. Multi-stress testing is able to demonstrate deficiencies of polymer insulator materials and designs, including the nature of interfaces in insulation design. We have investigated IEC 61109 Annex C (5000h aging test) and CEA tracking wheel test as test methods of artificial accelerated aging. The aging degree of polymer insulator is estimated by leakage current, measurement of hydrophobicity degree, damage conditions of insulator surface, withstand voltage test etc.

• 소성∙가공
• /
• 제25권6호
• /
• pp.390-395
• /
• 2016

GDI fuel rail is component of GDI system which directly fuel with high pressure in the engine combustion chamber. And it is required to high strength and dimensional accuracy. Multi roll-die drawing process consists of the idle roll-die and drawing die in tandem. In the course of drawing with roll-die, deformation takes place between the idle roller pair or pairs. The friction force decreases with the idle roll-die, enabling the reductions to be risen in one step. In this study, the caliber of 4-roll was designed into pass schedule that made the draw force at the exit of the drawing die be equal. In order to compensate for over-filling area, the roll caliber was modified using the result of FE-analysis. The results of FE-analysis and experiment show that the proposed design method can be used to effectively design the multi roll-die process, leading to an accurate shape and correct dimensions of the final within an allowable tolerance of ${\pm}0.08mm$. Furthermore, the productivity was evaluated by comparing with multi roll-die drawing process and conventional multi shape drawing process. The result was confirmed that it has an efficiency of about 2 times than conventional process in terms of time.

• 한국입자에어로졸학회지
• /
• 제12권3호
• /
• pp.57-63
• /
• 2016

The laser-induced breakdown spectroscopy (LIBS) has been used for rapid detection of elemental compositions of various materials in multi-media (solid, liquid, gas, and aerosols). In this study, the aerosol-LIBS has been developed for real-time monitoring of process-induced particles produced during the semiconductor manufacturing. The developed aerosol-LIBS mainly consists of laser, optics, spectrometer, and aerosol chamber. A new aerosol chamber was constructed for the aerosol-LIBS to be applied for various semiconductor manufacturing process, including exhaust tubes, and low pressure and high temperature chamber. The aerosol-LIBS was evaluated by using laboratory generated aerosols for detection of various elements. As a result, P, Fe, Mg, Cu, Co, Ni, Ca, Na, and K emission lines were successfully detected by the aerosol-LIBS. Further evaluation of the aerosol-LIBS is being conducted.

• 한국군사과학기술학회지
• /
• 제10권2호
• /
• pp.126-133
• /
• 2007

Lately, there exist growing demands to increase the firepower of mid-calibre automatic guns despite spatial limitations of armament. In this context, ammunitions of simple cylindrical shape are considered so advantageous that associated automatic guns are under development incorporating an intermittently rotating chamber mechanism. In this paper, relevant subsystems for such guns are to be described, and a digital controller to automate the entire system as well. Via dynamic simulations it proves to function well being able to drive the chamber at any constant speed up to 200spm, which is merely limited by the recoil performance. It is remarkable that the system synchronization idea in use is applicable to any other multi-actuator systems that should operate on the basis of event rather than time.

• International journal of advanced smart convergence
• /
• 제8권4호
• /
• pp.200-206
• /
• 2019

In this study, we compared the VacCAD and VacSim^(Multi), commercial vacuum simulators, to verify the advantages of VacCAD's efficiency. It was emphasized on immediacy and simplicity of simulation modelling, and characteristics of the pump combinations, pumping down curves, and vacuum materials. First, usability of simulation mechanism was estimated through the modeling schematics and obtained simulation results of each employed simulator were compared to evaluate the applicability in practice. Simulation reliability of each simulator was also probed by comparing the pumping characteristics of commercially available high vacuum systems. In addition, the degree of tolerances on VacCAD was also investigated through pumping down analysis considering outgassing effect due to chamber material variations. The higher effectiveness and expediency of VacCAD than VacSim^(Multi) has been presented, and it was expected that the utilization of VacCAD in vacuum applications to be increased.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.49-59
• /
• 2005

This paper describes a development of the extrusion process and estimation of the weldability for multi cell tubes used to cooling system of automobiles. A study on extrusion process is performed through the 3D FE simulation in non-steady state and extrusion experimentation. Also, nano-indentation test is employed to estimate the weldability of tubes. Especially, An evaluation of the weldability using the nano-indentation is accomplished as compared with nano-hardness in welded part and in the others. Finally, the pattern of the mandrel defection is investigated according to shapes of the porthole and/or chamber.

• 설비공학논문집
• /
• 제13권8호
• /
• pp.780-786
• /
• 2001

For the compressor speed control of a multi-type air conditioning system, a fuzzy control algorithm was developed. The sum of zone temperature errors and its derivative were used as input variables, and the compressor speed was selected as the output variable. To test the effectiveness of the control algorithm, one outdoor environmental chamber and four indoor environmental chambers were used. In the chambers the zone temperature step change test and the indoor unit change over test were performed. Test results showed that, for the control of compressor speed, the fuzzy control algorithm was more effective than the conventional proportional control algorithm for the energy conservation.

• 동력기계공학회지
• /
• 제4권1호
• /
• pp.33-38
• /
• 2000

The characteristics of center-driver jet pump which have multi-nozzle were studied in this research. Jet nozzles are connected outside of the bend rather than inserted in the bend in order to transport solid materials or fish without any harm. Jet pumps having one nozzle, two nozzles, four nozzles, and sixteen nozzles were tested in this study. The efficiencies and performances of jet pumps were studied for several nozzles shape, for three different mixing chamber shapes, for two suction area shapes. All the efficiency curves for these cases are presented in this paper.