• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.183-186
• /
• 1992

The distribution automation functions include feeder automation, data acquisition and processing, remote meter reading and load management. This report explains the function of feeder automation and the accomplishment method of feeder automation using the switches of distribution system with multi functions.

• Current Photovoltaic Research
• /
• v.8 no.4
• /
• pp.124-128
• /
• 2020

Output power of photovoltaic (PV) modules installed outdoors decreases every year due to environmental conditions such as temperature, humidity, and ultraviolet irradiations. In order to promote the installation of PV modules, the reliability must be guaranteed. One of the important factors affecting reliability is intermetallic compounds (IMC) layer formed in ribbon solder joint. For this reason, various studies on soldering properties between the ribbon and cell have been performed to solve the reliability deterioration caused by excessive growth of the IMC layer. However, the IMC layer of the PV module interconnected by multi-wires has been studied less than using the ribbon. It is necessary to study soldering characteristics of the multi-wire module for improvement of its reliability. In this study, we analyzed the growth of IMC layer of the PV module with multi-wire and the degradation of output power through damp-heat test. The fabricated modules were exposed to damp-heat conditions (85 ºC and 85 % relative humidity) for 1000 hours and the output powers of the modules before and after the damp-heat test were measured. Then, the process of dissolving ethylene vinyl acetate (EVA) as an encapsulant of the modules was performed to observe the IMC layer. The growth of IMC layer was evaluated using OM and FE-SEM for cross-sectional analysis and EDS for elemental mapping. Based on these results, we investigated the correlation between the IMC layer and output power of modules.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.6_2
• /
• pp.827-839
• /
• 2021

Due to climate change and population growth, water scarcity is getting worse all over the world. Among various methods for desalination of seawater, the Multi-Effect Adsorptive Desalination method, which combines the existing Multi-Effect Desalination method and the Adsorptive Desalination method and can produce high-concentration-high-concentration freshwater, is emerging. Because the Multi-Effect Adsorptive Desalination method combines the two different methods, the system becomes complicated and the possibility of failure increases. Therefore, in this study, availability analysis was performed on the Multi-Effect Adsorptive Desalination process. A total of four types of reliability block diagrams were presented, and availability analysis was conducted based on them. The first form of a reliability block diagram is configured in series without any redundancy. The availability of the reliability block diagram composed of the serial system was found to be lower than the required availability. In order to increase availability, the redundancy to pumps and boiler are added to system. As a result of availability analysis, it was confirmed that designing desalination systems with redundancy to pump meets the 93% availability, which is typically required availability for various plants.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.5
• /
• pp.2509-2528
• /
• 2019

There are various styles of license plates for different countries and use cases that require style-specific methods. In this paper, we propose and illustrate a multi-style license plate recognition system. The proposed system performs a series of processes for license plate candidates detection, structure classification, character segmentation and character recognition, respectively. Specifically, we introduce a license plate structure classification process to identify its style that precedes character segmentation and recognition processes. We use a K-Nearest Neighbors algorithm with pre-training steps to recognize numbers and characters on multi-style license plates. To show feasibility of our multi-style license plate recognition system, we evaluate our system for multi-style license plates covering single line, double line, different backgrounds and character colors on Korean and the U.S. license plates. For the evaluation of Korean license plate recognition, we used a 50 minutes long input video that contains 138 vehicles of 6 different license plate styles, where each frame of the video is processed through a series of license plate recognition processes. From two experiments results, we show that various LP styles can be recognized under 50 ms processing time and with over 99% accuracy, and can be extended through additional learning and training steps.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.10
• /
• pp.2376-2394
• /
• 2013

In order to ensure both of the whole system capacity and users QoS requirements in heterogeneous wireless networks, admission control mechanism should be well designed. In this paper, Multi-agent Q-learning based Admission Control Mechanism (MQACM) is proposed to handle new and handoff call access problems appropriately. MQACM obtains the optimal decision policy by using an improved form of single-agent Q-learning method, Multi-agent Q-learning (MQ) method. MQ method is creatively introduced to solve the admission control problem in heterogeneous wireless networks in this paper. In addition, different priorities are allocated to multiple services aiming to make MQACM perform even well in congested network scenarios. It can be observed from both analysis and simulation results that our proposed method not only outperforms existing schemes with enhanced call blocking probability and handoff dropping probability performance, but also has better network universality and stability than other schemes.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.22-24
• /
• 2003

In this work, in order to investigate the effect of multiple lightning impulse currents on zinc oxide arrester blocks. We have been designed and fabricated a multi-impulse generator which can produce quintuple voltages with $1.2/50{\mu}s$ to 100kV and quintuple currents with $8/20{\mu}s$ to 12kA and we have evaluated the characteristics of zinc oxide arrester block using several electrical and physical methods after the multi-impulse test. It was found that the multi-impulse failures of ZnO arrester blocks were mainly caused by surface flashover and the multi-impulse currents test would be more suitable than single impulse current test in evaluation of the characteristics of zinc oxide arrester blocks corresponding to actual situations.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.178-179
• /
• 2014

In this study, $Ni-W-Si_3N_4$ alloy composite coatings were prepared by pulse electrodeposition method using nickel sulfate bath with different contents of tungsten source, $Na_2WO_4.2H_2O$, and dispersed $Si_3N_4$ nano particles. The structure and microstructure ofcoatings was separately analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). Results indicated that nano $Si_3N_4$ and W content in alloy had remarkable effect on microstructure, microhardness and scratch resistant properties. Tungsten content in Ni-W and $Ni-W-Si_3N_4$ alloy ranged from 7 to 14 at.%. Scratch test results suggest that as compared to Ni-W only, $Ni-W-Si_3N_4$ prepared from Ni/W molar ratio of 1:1.5 dispersed with 20 g/L $Si_3N_4$ has shown the best result among different samples.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.43-44
• /
• 2015

Electrodeposited Ni and Ni-SiC composite coatings were prepared on Cu substrates by using the Ni-Sulfamate electrolytic bath. Thus prepared samples were subjected for the two different types of post surface modification techniques; i.e. Laser Surface Texturing (LST) and Ultrasonic Nano Surface Modification (UNSM), respectively in order to investigate their effects on surface and interface related properties of the coatings. Hemispherical dimples, with 80 to 200 um dimple spacing, were created and examined on the surfaces of the materials studied. The results revealed that micro-surface texturing with 150 um dimple spacing considerably improved the coefficient of friction. Dimple spacing accuracy and incorporated second phase ceramic particles both contributed significantly to reduction in coefficient of friction. On the other hand, application of UNSM considerably modified the surface topography, led to increase the Vickers microhardness, and reduced the wear and coefficient of friction as compared to non UNSM treated Ni and Ni-SiC samples.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.263-265
• /
• 2003

The computation cost of image registration is affected by searching data size and space. This paper proposes an efficient image registration algorithm that uses multi-resolution wavelet decomposed image to reduce the data size search. The algorithm determines the correlation detection at low resolution on low-pass sub bands of wavelet and generate mask for higher resolution as part of a coarse to fine registration algorithm. The correlation matching is defined for coarse resolution similarity measurement, while mutual information (MI) is used at fine resolution. The results show that the new efficient mask-based algorithm improves computational efficiency and yields robust and consistent image registration results.

• Architectural research
• /
• v.12 no.1
• /
• pp.1-8
• /
• 2010

This research paper explores selected behavioral outcomes of a multi-sensory environment. An experimental study was conducted at a specialized facility for the ageing in Sweden. The objective was to explore the effects of agitated behaviors of ageing residents with dementia and to identify any short-term effects. Appointed nursing staff was instructed to record physically and verbally agitated behaviors on three occasions; pre-session, mid-session, and post-session. Over seven months, nine participants received sixty-one sessions in the multi-sensory room. ANOVA and Post hoc multiple comparisons were performed to identify the differences in mean between each session. Generally irritated/frustrated behavior and eating/drinking non foods revealed statistically significant differences, while there were no significant results in verbally agitated behavior. One short-term effect was observed in one agitated category; a reduction of generally irritated/frustrated behavior. These results suggest that the multi-sensory environment can have positive effects on some manifestations of agitated behavior. This study proposes that a multi-sensory environment may be recommended as an alternative intervention for physically agitated behavior among this category of residents. However, more research is needed to understand the specific effects and the best use of the multi-sensory environment for this population.