• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2934-2939
• /
• 2008

We conducted a test of a direct burning of crude Jatropha oil (CJO) in a commercial boiler system. The fuel, crude Jatropha oil is not biodiesel which comes from transeterification process of bio oil, but it is pure plant oil. The higher heating value (HHV) of the CJO is 39.3 MJ/kg (9,380 kcal/kg) and is higher than that of a commercial heating oil, 37.9 MJ/kg. The kinematic viscosity of CJO is 36.2 mm2/s at $40^{\circ}C$ and 8.0 mm2/s at $100^{\circ}C$. The burner used in the test is a commercial burner for a commercial heatingoil and its capacity is 140 kW (120,000 kcal/h). We did a preliminary test whether the combustion is stable or not. The preliminary test was a kind of open air combustion test using the commercial burner with crude Jatropha oil. We found that the combustion can be stable if the crude Jatrophaoil temperature is higher than $90^{\circ}C$. We measured the flue gas concentration by using a gas analyzer. The NOx concentration is $80{\sim}100\;ppm$ and CO concentration is nearly 0 ppm at flue gas O2 concentration of 3.0 and 4.5%.

• Journal of the Korean Society of Combustion
• /
• v.18 no.2
• /
• pp.1-7
• /
• 2013

Flame stabilization characteristics of premixed flames in narrow annular coaxial tubes (NACT) were investigated experimentally. The NACT burner was proposed as a model of a cylindrical refractory burner, and it was made of quartz tubes. Flame stabilization conditions affected by the characteristic length of the burner was investigated with the variation of the equivalence ratio and the flow rates. Flame behaviors in narrow spaces could be directly observed. Conclusively, more wide flame stabilization conditions could be obtained at the case of the decreased channel scale. A flame instability, such as combustion noise was detected concerned with the flame oscillation observed at the surface of multi channel stage. Some flame propagation characteristics had complicated tendencies that may exist in practical porous-media combustors. Therefore, this NACT burner can be a basic configuration for the development of flame stabilization model in porous media combustor, and it will enhance our understanding about the behavior of flames in meso-scale combustion spaces.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.2
• /
• pp.45-51
• /
• 2002

Recently the interest for the environment is increasing. So the criterion for the evaluation of the burner has changed. For efficient driving problem, if the thermal efficiency is higher and the oxygen in exhaust gas is lower, then burner is evaluated better. For environmental problem. burner must satisfy NOx limit, soot limit and CO limit. Generally the experienced operator judge of the combustion status of the burner by the color of flame. we don't still have any satisfactory solution against it. the relation of the combustion status and the color of the flame hasn't still been established. This paper is the study about the relation of the combustion status and the color of the flame. This paper describes development of real time flame diagnosis technique that evaluate and diagnose combustion state such as consistency of components in exhaust gas, stability of flame in quantitative sense. In this paper, it was proposed on the flame diagnosis technique of burner using image processing algorithm, the parameter extracted from the image of the flame was used as the input variables of the flame diagnostic system. at first, linear regression algorithm and multiple regression algorithm was used to obtain linear multi-nominal expression. Using the constructed inference algorithm, the amount of NOx and CO of the combustion gas was successfully inferred. the combustion control system will be realized sooner or later.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.96-104
• /
• 2013

Coal gasification is considered as one of the best alternatives among clean coal technology and new concept next generation technologies are under being developed to achieve low cost as well as high efficiency. In this study we have developed double swirl multi-burner as part of the development of low cost compact gasifier. We installed new concept multi-burner with pulverized coal distributor to the body of existing gasifier for burner test. Gasification test was performed under the condition of $6.4{\sim}7.2kg/cm^2$ and $1170{\sim}1300^{\circ}C$ by using Indonesian ABK (sub-bituminous) coal to get operation condition of new concept multi-burner. Our interest was focused to ensure a stable operating condition rather than the gasifier performance evaluation. As a result, we were able to achieve the carbon conversion of 84% and the cold gas efficiency of 52.1% at the stable operating conditions.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.162-169
• /
• 2005

The performance of oxygen combustion with $CO_2$ feeding was investigated in a pyrex tube furnace. The inverse type multi-hole burner was used for improving mixing and wide operating range. It introduced oxygen, fuel, and oxygen, respectively, from center tube to outer tubes. Oxygen combustion characteristics with excess oxygen ratio, oxygen feeding ratio, and $CO_2$ feeding flow rate were studied to optimize the operating condition and to apply the oxygen combustion with recirculation of flue gas to a real furnace. This paper presents results on the effect of $CO_2$ feeding flow rate on the structure of the flames and concentrations of NO and CO emissions. The visible flame length was shortest due to well mixing between fuel and oxygen when the oxygen feeding ratio was 0.25. The NO emission was reduced drastically regardless of excess oxygen ratio when the $CO_2$ feeding flow rate was larger than 15 lpm. The CO emission is varied by changing the $CO_2$ feeding flow rate but the CO emission characteristics is highly affected by excess oxygen ratio. When the excess oxygen ratio is below ${\lamda}=1.1$, the CO emission increased as the $CO_2$ feeding flow rate increased.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1025-1030
• /
• 2008

We develop heat exchanger modules for a multi-burner boiler. The heat exchanger module is kind of a heat recovery steam generator (HRSG). This heat recovery system has 4 heat exchanger modules. The 1st module consists of 27 bare tubes due to high temperature exhaust gas and the others consist of 27 finned tubes. The maximum steam pressure of each module is 10 bar and tested steam pressure is 4 bar. In order to test these heat exchanger modules, we make a 0.5t/h flue tube boiler (LNG, $40\;Nm^3/h$). The test results of 100% boiler load show that heat transfer rate of 1st module is 49.7 Mcal/h which is 34% of total heat transfer rate and that of 2nd module is 82.6 Mcal/h which is 57% of total heat transfer rate. The reason of higher the heat transfer rate of 2nd module than that of 1st module is that the 2nd heat exchanger module has finned tubes instead of bare tube. The boiler load 50% results show that only 2 heat exchanger modules are needed to extract the heat from the flue gas to water. From this result, it is very important of optimum design of the first finned tube among all water tubes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.11
• /
• pp.1594-1605
• /
• 2001

In this study, a numerical simulation was developed which was capable of predicting the characteristics of NO formation in pilot scale combustor adopting the air-staged burner flame. The numerical calculation was constructed by means of establishing the mathematical models fur turbulence, turbulent combustion, radiation and turbulent nitric oxide chemistry. Turbulence was solved with standard k-$\xi$ model and the turbulent combustion model was incorporated using a two step reaction scheme together with an eddy dissipation model. The radiative transfer equation was calculated by means of the discrete ordinates method with the weighted sum of gray gases model for CO$_2$and H$_2$O. In the NO chemistry model, the chemical reaction rates for thermal and prompt NO were statistically averaged using the $\beta$ probability density function. The results were validated by comparison with measurements. For the experiment, a 0.2 MW pilot multi-air staged burner has been designed and fabricated. Only when the radiation was taken into account, the predicted gas temperature was in good agreement with the experimental one, which meant that the inclusion of radiation was indispensable for modeling multi-air staged gas flame. This was also true of the prediction of the NO formation, since it heavily depended on temperature. Subsequently, it was found that the multi-air staged combustion technique might be used as a practical tool in reducing the NO formation by controlling the peak flame temperature.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.3-4
• /
• 2012

Characteristics of the flow in the incinerator were studied in terms of the cold flow and combustion using multi-staged tangential burner. The design parameters such as deflection angle of main nozzle, and decline angle of assist nozzle habe been changed. The effects of each parameter on burning characteristics have been investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.8
• /
• pp.1061-1070
• /
• 2003

A triple flame in a mixing layer was studied experimentally with concentration gradient and mean velocity by using a multi-slot burner, which can stabilize the lift-off flame. Flame stabilization condition, lift-off heights, and some other characteristics were examined for methane and propane flame within a range of very low concentration gradient. Pitot-tube and LDV(Laser Doppler Velocimetry) were used for velocity. Mass spectroscopy and Rayleigh scattering signal were used for concentration gradients. Thermo-couples and SiC TFP(Thin Filament Pyrometer) were used for temperature. It was found that minimum values of the lift-off heights exist at a certain concentration gradient for constant mean velocity and this means that the propagation velocity has a maximum value. The scales of flame to the burner nozzle and intensity variation of the diffusion flame were suspected as the cause.

• Journal of the Korean Society of Combustion
• /
• v.18 no.3
• /
• pp.24-30
• /
• 2013

Flame stabilization characteristics of premixed flames in an annular coaxial 5-tubes burner (AC5TB) were investigated experimentally. The AC5TB was made of five quartz tubes, and the flame stabilization conditions in that burner were investigated with the variation of equivalence ratio and the flow velocities. Flame behaviors inside of narrow annular tubes could be observed directly. Overall flame stabilization conditions were similar to that of the previous study, while the flame behaviors and structures were different mainly due to the controlled uniform distribution of the velocities in channels. Flame flashback conditions were thought to be governed by the competition between heat release rate, heat loss and heat recirculation in each channel. Stationary flames at a fixed location were compared in its velocity distribution and burned gas temperature across the channel. This AC5TB can be a basic configuration for the development of flame stabilization model of porous media combustors, and it will help understand about the real behavior of flames in meso-scale combustion spaces.