• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.153-156
• /
• 2005

Nondestructive sensing of electrospun PYDF web and multi-wall carbon nanotube (MWCNT)/epoxy composites were investigated using electro-micromechanical technique. Electrospinning is a technique used to produce micron to submicron diameter polymeric fibers. Electrospun PVDF web was also evaluated for the sensing properties by micromechanical test and by measurement electrical resistance. CNT composite was especially prepared for high volume contents, 50 vol% of reinforcement. Electrical contact resistivity on humidity sensing was a good indicator for monitoring as for multifunctional applications. Work of adhesion using contact angle measurement was studied to correlate acid-base surface energy between carbon fiber and CNF composites, and will study furher for interfacial adhesion force by micromechanical test.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.499-500
• /
• 2010

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2017년도 춘계 종합학술대회 논문집
• /
• pp.485-486
• /
• 2017

치과용 글라스아이오노머(GIC)는 치과에서 폭넓게 응용되고 있는 재료 중 하나이다. 그러나 GIC의 낮은 기계적 특성으로 인해 구강내 사용범위가 제한적이다. 이에 본 연구는 기능성 다중벽 탄소나노튜브(multi wall carbon nanotube; MWCNT-COOH)를 각 농도별(0.25-1.0 wt%)로 기존의 분말에 첨가하여 복합체를 제조한 후 제조사의 지시에 따란 분말(2):액(1)의 비율로 시편을 제작하여 다중벽탄소나노튜브가 GIC의 기계적 특성과 항균효과에 미치는 영향을 조사하였다.

• 설비공학논문집
• /
• 제27권1호
• /
• pp.1-7
• /
• 2015

A boiling heat transfer system is used in a variety of industrial processes and applications, such as refrigeration, power generation, heat exchangers, cooling of high-power electronics components, and cooling of nuclear reactors. The critical heat flux (CHF) is the thermal limit during a boiling heat transfer phase change; at the CHF point, the heat transfer is maximized, followed by a drastic degradation beyond the CHF point. Therefore, Enhancement of CHF is essential for economy and safety of heat transfer system. In this study, the CHF and heat transfer coefficient under the pool-boiling state were tested using multi-wall carbon nanotubes (MWCNTs) CM-95 and CM-100. These two types of multi-wall carbon nanotubes have different sizes but the same thermal conductivity. The results showed that the highest CHF increased for both MWCNTs CM-95 and CM-100 at the volume fraction of 0.001%, and that the CHF-increase ratio for MWCNT CM-100 nanofluid with long particles was higher than that for MWCNT CM-95 nanofluid with short particles. Also, at the volume fraction of 0.001%, the MWCNT CM-100 nanofluid indicated a 5.5% higher CHF-increase ratio as well as an approximately 23.87% higher heat-transfer coefficient increase ratio compared with the MWCNT CM-95 nanofluid.

• 한국수소및신에너지학회논문집
• /
• 제12권1호
• /
• pp.65-73
• /
• 2001

Carbon nanotubes were prepared by catalytic decomposition of $CH_4$ using Ni-MgO catalyst at various temperatures. $H_2$ effect on crystallinity and morphology during the synthesis of carbon nanotubes was investigated. The crystallinity and morphology were characterized by SEM, TEM, XRD, TGA, and Raman spectroscopy. In addition, the hydrogen adsorption properties were evaluated by PCT measurement in a hydrogen pressure range between 1 and 120 bar. The optimal synthesis temperature of carbon nanotubes was elevated in the presence of $H_2$, although significant difference of carbon nanotube morphology was not found. It is believed that hydrogen served as self-cleaner mops the amorphous carbon on the catalyst surface. It is proved that the carbon nanotubes have multi-walled structure, short length with a outer diameter of 20 ~40nm and open tips after elimination of the catalyst. The amount of hydrogen adsorbed in carbon nanotubes is increased as the pressure of hydrogen is increased and reaches 1.3 wt % under the hydrogen pressure of 120 bar at room temperature.

• 한국응용과학기술학회지
• /
• 제22권1호
• /
• pp.35-42
• /
• 2005

Aligned multi-wall carbon nanotubes (MWNTs) were synthesized through the catalytic decomposition of hydrocarbons in a quartz tube reactor. In this study, we investigated the influence of gas flow rate of feedstock on the structure and growth rate of vertically aligned carbon nanotubes produced by the floating catalyst method. As the flow rate of feedstock increased, the nanotube diameter became smaller and the length became longer. Although the growth rate also increased with the raise of flow rate, the optimum flow rate of feedstock existed for the crystallinity of carbon nanotubes.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.245-255
• /
• 2017

High energy ball milling is employed to produce iron matrix- multiwall carbon nanotube (MWCNT) reinforced composite. The damage caused to MWCNT due to harsh ball milling condition and its influence on interfacial bonding is studied. Different amount of MWCNT is used to find the optimal percentage of MWCNT for avoidance of the formation of chemical reaction product at the matrix - reinforcement interface. Effect of process control agent is assessed by the use of different materials for the purpose. It is observed that ethanol as a process control agent (PCA) causes degradation of MWCNT reinforcements after milling for two hours whereas solid stearic acid used as process control agent, allows satisfactory conservation of MWCNT structure. It is further noted that at a high MWCNT content (~ 2wt.%), high energy ball milling leads to reaction of iron and carbon and forms iron carbide (cementite) at the iron-MWCNT interface. At low percentage of MWCNT, dissolution of carbon in iron takes place and the amount of reinforcement in iron matrix composite becomes negligibly small. However, under the present ball milling condition (ball to metal ratio~ 6:1 and 200 rpm vial speed) iron-1wt.% MWCNT composite of good interfacial bonding can retain the tubular structure of reinforcing MWCNT.

• 설비공학논문집
• /
• 제28권3호
• /
• pp.95-102
• /
• 2016

A boiling heat transfer is used in various industry such as power generation systems, heat exchangers, air-conditioning and refrigerations. In the boiling heat transfer system, the critical heat flux (CHF) is the important factor, and it indicated safety of the system. It has kept up studies on the CHF enhancement. Recently, it is reported the CHF enhancement, when working fluid used the nanofluid with high thermal properties. But it could be occurred nanoflouling phenomenon from nanoparticle deposition, when nanofluid applied the heat transfer system. And, it is reported that the safety and thermal efficiency of heat transfer system could decrease. Therefore, it is compared and analyzed to the CHF and the boiling heat transfer coefficient on effect of artificial nanofouling (coating) in oxidized multi-wall carbon nanotube nanofluids. As the result, the CHF of oxidized multi-wall carbon nanofluids and the CHF of artificial nanofouling in the nanofluids increased to maximum 99.2%, 120.88%, respectively. A boiling heat transfer coefficient in nanofluid increased to maximum 24.29% higher than purewater, but artificial nanofouling decreased to maximum -7.96%.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.194-199
• /
• 2021

In this study, rebar corrosion detection sensor was fabricated using multi-walled carbon nanotubes (MWCNTs). MWCNTs were pre-treated in the acid electrolytes to attach the carboxylic acid to the surface of MWCNTs. The fabricated sensor was attached on the surface of rebar and it detected the corrosion of steel using LCR meter with variation of capacitance. The surface morphology and electrical properties were characterized using scanning electron microscope (SEM) and electrical test equipment, respectively. To verify the corrosion detection characteristics, comparison experiment using plastic bar was performed. Moreover, mechanism of corrosion detection sensor was discussed.

• 분석과학
• /
• 제27권6호
• /
• pp.308-313
• /
• 2014

염료감응형 태양전지의 광전극 및 상대전극에 탄소나노튜브를 도입하여 전지의 광전기적 특성 변화를 EIS, J-V 특성곡선 및 UV-Vis 분광기를 이용하여 분석하였다. $TiO_2$ 광전극의 전기전도도 및 광전효율을 향상시키기 위해 전자전달 촉진자 역할을 하는 multi-wall carbon nanotube (MWCNT)를 $TiO_2$와 혼합하여 $TiO_2$-MWCNT 복합체를 sol-gel 연소 복합공정을 통해 제조하여 조사한 결과 0.1 wt% MWCNT를 첨가한 경우, $TiO_2$만을 사용한 경우에 비해 약 12.5%의 향상된 효율을 보였다. $TiO_2$-MWCNT 복합체에서 MWCNT가 $TiO_2$ 층의 전자이동을 향상시켜 저항을 감소하고 염료와 전자의 재결합을 감소시킨 결과로 생각된다. 그러나 0.1 wt%보다 많은 MWCNT를 첨가할 경우 광투과도 및 염료의 흡착량을 감소시켜 효율이 감소하였다. 또한 상대전극에 MWCNT와 MWCNT-Pt를 적용하였을 경우 각각의 효율은 1.2%와 4.1%로 MWCNT만 적용할 때 보다 백금이 담지된 MWCNT를 사용하였을 경우에 백금과 비슷한 효율을 보였다.