• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.887-888
• /
• 2006

Switched Reluctance Motor(SRM) is rotated by reluctance force generated between rotor pole and stator pole. So SRM must be switched by exciting current according to rotor position. but SRM takes the advantages of high speed driving and very simple structure. The single phase SRM can not be start by itself and torque ripple is generated more than multi-phase SRM. But mechanical structure and driver is simpler than multi-phase SRM. The single phase SRM driver is composed with the absolute encoder and DSP to control exciting section and current, and is supplied by constant voltage. So The paper is intend to measure the speed charactrer of double silent pole type SRM by using the unipolar driving curcuit.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.775-779
• /
• 2003

Recently, a new type actuator using multi-pole magnet has been developed for high-density and high-speed disk drive, which can be achieved higher sensitivity than a conventional actuator for applying one-pole magnet. However, it is very difficult for the actuator of multi-pole magnet to meet simultaneously the optimal design condition for reducing rolling mode effect and improving driving sensitivity because the force center is different from the mass center In this paper, First We propose the new shape coil for tracking which can reverse moment additionally in tracking motion, Next we achieve the optimal design to reduce phase disturbance and peak gain at the rolling mode frequency. Finally, the validity of the proposed methods is proved from experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1212-1219
• /
• 2009

In this paper, a state feedback gain controller using linear matrix inequality(LMI) for the multi-objective synthesis is designed, in the multi-layer structure with integral type servo system. The design objectives include $H_{\infty}$ performance, asymptotic disturbance rejection, time-domain constraints, on the closed-loop pole location. The results of computer simulation show the validity of the designed controller.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.10
• /
• pp.85-89
• /
• 2010

During a ground fault the maximum fault current and neutral to ground voltage will appear at the pole nearest to the fault. Distribution lines are consisted of three phase conductors, an overhead ground wire and a multi-grounded neutral line. In this paper phase to neutral faults were staged at the specified concrete pole along the distribution line and measured the ground fault current distribution in the ground fault current, three poles nearest to the fault point, overhead ground wire and neutral line. A effect by grounding resistance of poles of ground fault current in the 22.9[kV] multi-ground distribution system. by field tests.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.123-126
• /
• 2002

A proposed multi-layer ceramic (MLC) chip type band-pass filter (BPF) is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coulped stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The passband and attenuation pole depend the coupling between resonators and coupling capacitance. The frequency characterics of the passband and attenuation pole are analysed with the variance of the coupling between resonators and coupling capacitance. An equivalent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the BPF is well acceptable for IMT-2000 application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.740-743
• /
• 2003

A multi-layer ceramic (MLC) chip type band-pass filter (BPF) is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coulped stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The passband and attenuation pole depend on the coupling between resonators and coupling capacitance. The frequency characterics of the passband and attenuation pole are analyzed with the variation of the coupling between resonators and coupling capacitance. An equivanlent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the BPF is well acceptable for IMT-2000 application.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1031-1032
• /
• 2007

In order to reduce the cogging torque, by predicting the variation of the cogging torque according to pole arc/pitch ratio by analytical and FE methods, pole arc/pitch ratio which makes the cogging torque minimum are determined. And then, the measurements of cogging torque for permanent magnet generators with determined pole arc/pitch ratio are presented. The reasons for the error between predicted and measured value are discussed fully in terms of the shape of permanent magnet. Finally, by confirming that predicted results for cogging torque according to pole arc/pitch ratio and skew are shown in good agreement with those obtained from measured one, the validation of analysis results is confirmed.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.135-137
• /
• 2002

In the favor of adjusting microwave signal, Hairpin type Filter, which delay microwave signal enough to several nanosecond, is a key component. One of the main advantage in using Hairpin type Filter is a conveniency for equipping with Delay Module, and because of having a wide bandwidth, Hairpin type Filter can be designed to satisfy the most applications. In this work, we attempted to estimate the delay time in a superconductive hairpin type filter A software to synthesize even and odd order equiripple hairpin type filter has been developed. This software arbitrarily locate its transfer zeros making symmetric of asymmetric amplitude response and equalizing group delay. Borland C++ compiler has been used. The program was designed to run under MS-DOS, Window 98, Window 2000. The program optimizes the position of the transfer function zeros in order to fulfill the group delay specification masks. We designed and fabricated a hairpin type HTS 2-pole microstrip bandpass filter to operate at 5.8Ghz. The fabrication method was pulsed laser deposition and YBCO films were deposited on sapphire substrates with a Ce$O_{2}$ thin layer as a buffer layer. We also developed a new style hairpin type filter by using interdigitide inner-pole. Compared to the same size regular hairpin type filters, our filters had a lower center frequency.

• Journal of the Korean Magnetics Society
• /
• v.2 no.2
• /
• pp.145-149
• /
• 1992

The characteristics of electromagnetic devices with permanent magnet depends greatly on the remanence pattern of permanent magnet. So, it is necessary to analyze the pattern of remanence in permanent magnet. This paper presents a finite element analysis of magnetizer considering the nonlinearity and anisotropy of yoke and magnet in magnetizer. The distributions of magnetizations are obtained according to the variations of magnetizing currents for two kinds of magnetizers with different magnetizing poles. It is found that the excessive magnetizing current results in the reduction and polarity reversion of magnetization in the multi-pole magnetizing system where the pole angle is too small. During the design and analyzing of multi-pole magnetizer, it must be considered that there exists an optimal value of magnetizing current and pole angle of magnetizer.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.38-40
• /
• 2009

In order to achieve a gearless construction of the wind energy conversion system(WECS), a low-speed generator should be used. Of the various candidate machine types, radial-field, multi-pole, permanent magnet, synchronous machines may be used for low-speed applications. So, this paper deals with the design of direct-coupled, multi-pole radial field machines with permanent magnet(PM) excitation for wind power applications for cogging torque reduction through the determination of optimum pole arc/pitch ratio. On the basis of an equivalent magnetic circuit method(EMCM) and a space harmonic method(SHM), an initial design is performed considering restricted conditions. And then, a detailed design is made using a non-linear finite element analyses(FEA). Finally, test results concerning generating characteristics are given to confirm the validation of the design.