• 센서학회지
• /
• 제9권4호
• /
• pp.307-315
• /
• 2000

FBG (Fiber Bragg Grating) hydrophone sensor의 arrays system을 구축하고, 수중에서 넓은 영역에 대한 다중점 신호 검출을 구현하기 위하여, WDM(Wavelength Division Multiplexing) 방법과 passive band-pass filter system을 이용하여, 설계 및 제작된 2개의 FBG transducers의 수중 음향파 신호 검출을 실행하였다. 실험 결과 수중에서 주파수 1.3 KHz대까지 다중점에 대하여, 주파수 신호가 각각 다른신호의 검출이 가능하였다. 따라서, 제작된 FBG transducers을 이용한 hydrophone sensor arrays의 시스템 설계가 가능함을 확인하였다.

• Korean Journal of Acupuncture
• /
• 제28권4호
• /
• pp.41-48
• /
• 2011

Objectives : This study aimed to explore the passive multi-channel time series analysis method by measuring bio-potentials of acupuncture point and the peripheral region Methods : Bio-potential was measured at ST36 and the peripherical region of ST36 of 5 healthy volunteers at three times. The diagram of the potential changes over time were smoothed by moving average method and similarities of ST36 and the other points were calculated. Results : In the normal weight group, bio-potential similarity tended to decrease in proportion to the distance from the acupuncture point. In the obesity group, bio-potential similarity appeared in a very wide area. Bio-potential similarity had positive correlation with BMI value. Conclusions : The passive multi-channel time series analysis method showed the possibility be appropriate for the electrical characteristics study of meridians.

• 디지털콘텐츠학회 논문지
• /
• 제8권1호
• /
• pp.85-91
• /
• 2007

본 논문에서는 포인트 샘플링을 이용한 음함수 곡면에서 나타나는 앨리어싱을 줄이기 위한 새로운 하이브리드 앤티앨리어싱 방법을 제안한다. 하이브리드 앤티앨리어싱 방법은 하나의 음함수 곡면에 대해 Z-버퍼에서 나타나는 픽셀 값들의 차이를 구하여 세가지 형태의 Z-버퍼를 각각 사용하는 방법이다. 차이의 수준을 정하여 차이가 심할 때는 멀티 Z-버퍼를 사용하고 차이가 중간 정도일 때는 더블 Z-버퍼를 사용하며 차이가 경미할 때는 원래의 Z-버퍼만을 사용하여 3차원 객체를 표현하는 방법이다. 기존에 앤티앨리어싱 효과를 높이기 위하여 전체적으로 멀티 Z-버퍼를 사용하였는데 사용되는 Z-버퍼의 개수를 줄이면서 멀티 Z-버퍼를 사용한 것과 비슷한 효과를 보이는 효율적인 방법이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.618-623
• /
• 2001

In a practical vibration isolation system, vibration is transmitted from the source to the receiver through several paths such as more than one inter-connected point and multi-degree of freedom at each connection point. Therefore, the major path investigation for vibration transmission among them is often required in a point of view of isolation. For the path analysis of multi-dimensional vibration isolation system, it is useful to employ the concept of vibration power in high frequency range where radiation of noise from the receiver structure is concerned. The idea is simple to understand and formulate but rather complicated to apply in practice. For an accurate estimation of power flow especially over a high frequency range, it is well known in theory that rotational motions should be taken into consideration together with translational motions at inter-connected points. In reality, however, power transmissions related to rotational terms are often neglected mainly due to difficulties in the instrumentation. In this paper, necessary formula and measurable mechanical quantities for vibration power analysis will be reviewed and experimental results with rotational terms included for compressor system in a commercial air conditioner will be shown.

• 한국정보전자통신기술학회논문지
• /
• 제2권2호
• /
• pp.37-43
• /
• 2009

본 논문에서는 저 전력 시스템에 적합한 고정 소수점 연산기로 구현된 다중 채널 디지털 보청기 알고리즘의 최적화 기법을 제시한다. 먼저 입력 신호를 고속 MDCT(modified discrete cosine transform) 방법을 사용하여 주파수 대역 분할함으로써 알고리듬의 복잡도를 최소화 하였고, MDCT 출력을 비선형 대역 분할 과정을 거쳐 채널별 그룹핑을 한 다음, 각 채널 신호를 난청인의 청각 손실 정도에 따라 구성한 라우드니스 보상 함수(loudness compensation function: LCF)표를 이용하여 이득을 조절하고, 최종적으로 TDAC 기법을 구현하는 IMDCT(Inverse MDCT) 변환을 거쳐 보상된 출력을 합성한다. 모든 과정은 16비트 정수 연산으로 구현되며, 이득을 계산하기 위해 측정되는 로그 단위의 연산 과정은 미리 계산된 테이블과 고속 탐색 알고리듬을 이용하여 구현된다. 구성된 보청기 알고리즘의 성능을 컴퓨터 시뮬레이션을 통해 평가하였다.

• Journal of information and communication convergence engineering
• /
• 제11권2호
• /
• pp.69-81
• /
• 2013

Maintaining connectivity is essential in multi-hop wireless networks since the network topology cannot be pre-determined due to mobility and environmental effects. To maintain the connectivity, a critical point in the network topology should be identified where the critical point is the link or node that partitions the network when it fails. In this paper, we propose a new critical point identification algorithm and also present numerical results that compare the critical points of the network and H-hop sub-network illustrating how effectively sub-network information can detect the network-wide critical points. Then, we propose two localized topological control resilient schemes that can be applied to both global and local H-hop sub-network critical points to improve the network connectivity and the network resilience. Numerical studies to evaluate the proposed schemes under node and link failure network conditions show that our proposed resilient schemes increase the probability of the network being connected in variety of link and node failure conditions.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.220-223
• /
• 2008

Large curved plate blocks are widely used to construct hull structure in shipbuilding industry. Most curved plates are manufactured by using manual method called as line heating that use deformation caused by residual stress after local heating along a line which is perpendicular to the curvature direction. However, its working environment is poor and its formability is totally dependent on an experienced technician. In view of that, multi-point dieless forming (MDF) technology that use reconfigurable punch arrays instead of one piece die is proposed in this study. The MDF process is based on a concept of equivalent die surface made by numbers of punches which has round tip at the end of it. In this study, numerical simulation for common curvature type such as saddle shape was carried out. In addition, experiments in the plate forming process were also conducted to compare with the numerical results in view of final configuration. Consequently, it was noted that the proposed dieless forming method has considerable feasibility to substitute the new process for conventional manual method.

• 한국염색가공학회지
• /
• 제31권2호
• /
• pp.65-76
• /
• 2019

A multi-point touch input sensor having different sizes or different capacitance touch points connected by only one pair of signal transmission lines was fabricated using a polyimide film coated with a thin copper plate. The capacitance increases with the decrease in the number of sheets of fabric spacers placed between the two sheets of the polyimide film. Therefore, the touch input sensor could be manufactured without fabric spacers, which was possible by the action of the polyimide film as a dielectric material in the capacitor. On the multi-point touch sensor, higher capacitance was obtained when pressing wider-area touch points with 10mm to 25mm diameter on average. However, the capacitance of a system comprising two sheets of touch sensors was considerably low, causing a serious overlap of the capacitance values according to the data collected from the reliability test. Although the capacitance values could be increased by stacking several sheets of touch sensors, the overlap of data was still observed. After reducing the size of all touch points to 10mm and stacking up to eight sheets of sensors, reliable and consistent capacitance data was obtained. Five different capacitance signals could be induced in the sensors by pushing touch points simultaneously.

• Structural Engineering and Mechanics
• /
• 제68권5호
• /
• pp.633-638
• /
• 2018

One of the important problems in the vehicle design is vehicle handling and stability. Effective parameters which should be considered in the vehicle handling and stability are roll angle, camber angle and scrub radius. In this paper, a planar vehicle model is considered that two right and left suspensions are double wishbone suspension system. For a better analysis of the suspension geometry, a kinestatic model of vehicle is considered which instantaneous kinematic and statics relations are analyzed simultaneously. In this model, suspension geometry is considered completely. In order to optimum design of double wishbones suspension system, a multi-objective genetic algorithm is applied. Three important parameters of suspension including roll angle, camber angle and scrub radius are taken into account as objective functions. Coordinates of suspension hard points are design variables of optimization which optimum values of them, corresponding to each optimum point, are obtained in the optimization process. Pareto solutions for three objective functions are derived. There are important optimum points in these Pareto solutions which each point represents an optimum status in the model. In other words, corresponding to any optimal point, a specific geometric position is determined for the suspension hard points. Each of the obtained points in the Pareto optimization can be selected for a special design purpose by designer to create an optimum condition in the vehicle handling and stability.

• 한국정밀공학회지
• /
• 제12권4호
• /
• pp.67-77
• /
• 1995

In modern industry the requirement of automation of manufacturing process increases so that unmanned system has been popular as an ultimate goal of modern manufacturing process. In unmanned manufacturing process the tool fracture is a very serious problem because it results in the damage of workpieces and can stop the operation of whole manufa- turing system. In this study, image processing technique is used to detect the fracture of insert tip of face milling using multi-point-tool. In order to acquire the image information of fracture shape of rotation insert tip. We set up the optical system using a light beam chopper. In this system we can reduce the image degradation generated from stopped image of rotating insert tip using image restoration technique. We calculated the mean square error to diagnose the condition of tool fracture, and determind the criteria of tool fracture using experimental and staticstical method. From the results of this study we've developed non- contact detection technique of tool fracture using image processing method and proposed the fracture direction of automation and unmanned system considering the optimal time of tool change milling.