• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.4
• /
• pp.1024-1030
• /
• 2016

This study gives the vertical motion analysis due to changes in Submerged shape of Multi-Purpose Small Floating Body in irregular waves using the commercial code(MAXSURF v.20) based on the Panel method. To verify the commercial code prior to the analysis, we guarantees the reliability of this paper's results using the commercial code by comparing with the results of experimental results on Catamaran. The anlysis conditions are ITTC wave spectrum, each encounter angle. Finally, we analyze the result of ship's response spectra for vertical motions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.6
• /
• pp.677-684
• /
• 2006

An ejector is a fluid transfer device to be used for mixing of fluids, maintaining vacuum, and overcoming a poor suction condition. To date, most ejectors have been made from the casting process. which is time-consuming and high-cost process. Therefore, a new production method of ejectors is desired if any. In this experimental study, we proposed a new type ejector manufactured from the commercial fitting materials and the welding process, which is equipped with an orifice type nozzle. The proposed ejector has a good integrity compared with the conventional ejector because the fittings have manufactured by forging and they have more strength than the casting materials. Furthermore we adopted a multi-opening orifice type nozzle for improving a suction capacity and compared with a single-opening orifice type nozzle. From the experimental results. we confirmed that the multi-opening nozzle had a food suction capacity than the single-opening nozzle and the proposed new type ejector showed higher vacuum than the conventional type ejector in non-load condition. These improved characteristics suggests that a new type ejector by using the commercial fittings opens the feasibility to be adopted in various industry fields and that the increased suction capacity can be achieved by altering the nozzle design of a conventional ejector.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.60-64
• /
• 2010

This paper introduces reliability improvement and time saving in eddy current inspection by signal characteristic optimization of multi-coil eddy current array probe. In the past, Multi-coil array probe and single probe were used for the gas turbine rotor surface inspection & defect evaluation. The multi-coil array probe was used for the broad area inspection. But the signal deviations among multi-coil array probe are maximum 28% in commercial probe. This differences were considered to impedance differences among coils, so it is very difficult to evaluate exact defect size. The signal deviations among multi-coil array probe are maximum 28% in commercial probe. So, single coil inspection was used for exact defect sizing. The purpose of this study is to improve signal deviations of multi-coil array probe. The introduced new technology can improves this deviation by adjusting input voltage in each coil. At first, apply same voltage in each coil and collect signal amplitude of each coil. And calculate new input voltage based on signal amplitude of each coil. If the signal amplitude deviation is within 5% among multi-coil array probe, the signal amplitude of multi-coil array probe is reliable. The proposed technology gives 2% signal deviation among multi-coil array probe. The proposed new technology gives reliability improvement and inspection time saving in eddy current inspection.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.3 no.2
• /
• pp.49-56
• /
• 2008

This paper proposes a PC-based open architecture controller for a multi-axis robotic manipulator. The designed controller can be applied for various multi-axes robotic manipulators since the motion controller is implemented on a PC with its peripheral devices. The accuracy of the controller based on the computed torque method has been measured with the dynamic model of manipulator. Since the controller is implemented in the PC-based architecture, it is free from the user circumstances and the operating environment. Dynamics of the manipulator have been compensated by the feed forward path in the inner loop and the resulting linear outer loop has been controlled by PD algorithm. Using the specialized language, it can be more efficient in programming and in driving of the multi-axis robot. Unlike the conventional controller that is used to control only a specific robot, this controller can be easily changed for various types of robots. This paper proposes a PC-based controller that has a simple architecture with its simple interface circuits than general commercial controllers. The maintenance and the performance of the controller can be easily improved for a specific robot. In fact, using a Samsung multi-axis robot, AT1, the controller performance and convenience of the PC-based controller have been verified by comparing to the commercial one.

• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.150-155
• /
• 2002

A commercial CFD code is applied to analyze the 3-D viscous flow field within vertical multi-stage centrifugal pump including impeller with 6 blades and guide vane with 11 blades and is performed by changing flow rate from 10 to $26m^3/h$ at the constant 3500rpm. The purpose of this 3-D numerical simulation is not only to confirm how much the effect of three kinds of blade inlet breadth (11mm, 11.5mm, 12mm) of impeller has influence on the performance of vertical multi-stage pump but also to make clear the cause about performance difference at the exit side of impeller and guide vane. The vertical multi-stage pump consisit of the impeller, guide, vane and cylinder. The grid of numerical analysis used to the vertical multi-stage pump is 18,000, 45,000, and 100000 cells in case of the impeller, guide vane, cylinder and total grid is 730,000 cells. The characteristics such as total pressure coefficient, total head, shaft horse power, power efficiency at the exit side of impeller and guide vane, discharge coefficient are represented according to flow rage changing.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.04a
• /
• pp.95-102
• /
• 2004

The 1st and 2nd tension forces of the PSSC(Prestressed Steel and Concrete) girder constructed with commercial rolling beams and concrete are optimally designed. The design variables are the 1st and 2nd tension forces due to multi-step prestressing and live load. The objective function is set to the maximum live load. Design conditions are allowable stress at the top and bottom of slab, beam and infilled concrete due to a construction step. An Optimization of Matlab based program Is developed. The results show that the tendon position and concrete compression strength etc are important.

• IE interfaces
• /
• v.18 no.1
• /
• pp.44-51
• /
• 2005

The rapid expansion of the Internet-related technology has changed the current commercial transaction process. In the physical commercial transaction, most deals are accomplished through the negotiation process except a fixed price system. Thus, the negotiation is essential to conclude the business transactions. Especially, under the e-commerce environment, an automated negotiation system is necessary to respond quickly and flexibly to the diverse environmental changes and also to perform negotiations consistently and effectively. To this end, we develop an automated negotiation system using multi-agent technology. This new system includes such functions as creating negotiation proposals automatically, evaluating the counterpart’ proposals, and preparing counter offers.

• KIEAE Journal
• /
• v.6 no.1
• /
• pp.39-46
• /
• 2006

Multi-use housing and commercial buildings have been emerged according to social and economic changes of CBD in Seoul Metropolitan Areas. The purpose of this study is to clarify the characteristics of the multi-use building, to analyze the problems on the base of survey and to suggest the solutions for architectural planning, focusing on eco-friendly dwelling environment. A field survey with 46 subjects has been carried out with structured questionnaire. Some problems in planning of the complex building have been discussed in terms of environmental issues and design criteria. In conclusion, basic planning directions for improving the building environmental quality have been suggested.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.11
• /
• pp.1339-1347
• /
• 2004

Development of the low NOx heating boiler was strongly asked due to severe air pollution and the large number of boilers in korea. Compactness of the commercial boiler was also important because of low manufacturing cost and easy installation. In this study. newly developed compact low NOx burner, using turbulent gas diffusion combustion with multi-staged air supplies and multiple fuel nozzles, was investigated. Comparison study of the new burner was performed between experimental results and computational analysis. Commercial computational fluid dynamic(CFD) program named CFX-5.6 was used for numerical analysis of the low NOx burner inside the test combustor. Comparisons of experiment data and numerical result were performed under various equivalence ratio and fuel flow rate.

• Korean Institute of Interior Design Journal
• /
• v.14 no.5 s.52
• /
• pp.236-244
• /
• 2005

This study investigates the effects of the spatial elements of the mulit-purpose commercial complex on visitors' circulation pattern and wayfinding by employing method of space syntax, observation, and interview survey. Two commercial complexes were investigated; Techno-mart represented a vertical type and COEX mall rendered a horizontal one. Analysis of the spatial elements using space-syntax method provided a base line for comparing analyses by the two other methods. Analysis of the interview additionally survey identified the factors affecting wayfinding behavior and contributing satisfaction. The findings suggest that level of the effects of the spatial configuration on visitors' circulation pattern is greater in Techno-mart(vertically oriented) than COEX(horizontally). In COEX, for instance, specific route that connects sub-way station and cinema complex carries far more traffic than main route, even though the main route indicates higher degree of integration of spatial configuration. Similar with observation, the degree of integration is corresponding with the satisfaction and easiness of wayfinding behavior In COEX, specific place and feature seem to have more effects on visitors' wayfinding behavior and circulation pattern than the level of integration of spatial configuration.