• 전자공학회논문지C
• /
• 제34C권11호
• /
• pp.1-11
• /
• 1997

The transient current components of the dRAM are analyzed and the sensing current, data path operation current and DC leakage current are revealed to be the major curretn components. It is expected that the supply voltage of less than 1.5V with low VT MOS witll be used in multi-giga bit dRAM. A low voltage dual VT self-timed CMOS logic in which the subthreshold leakage current path is blocked by a large high-VT MOS is proposed. An active signal at each node of the nature speeds up the signal propagation and enables the synchronous DRAM to adopt a fast pipelining scheme. The sensing current can be reduced by adopting 8 bit prefetch scheme with 1.2V VDD. Although the total cycle time for the sequential 8 bit read is the same as that of the 3.3V conventional DRAM, the sensing current is loered to 0.7mA or less than 2.3% of the current of 3.3V conventional DRAM. 4 stage pipeline scheme is used to rduce the power consumption in the 4 giga bit DRAM data path of which length and RC delay amount to 3 cm and 23.3ns, respectively. A simple wave pipeline scheme is used in the data path where 4 sequential data pulses of 5 ns width are concurrently transferred. With the reduction of the supply voltage from 3.3V to 1.2V, the operation current is lowered from 22mA to 2.5mA while the operation speed is enhanced more than 4 times with 6 ns cycle time.

• Earthquakes and Structures
• /
• 제15권2호
• /
• pp.193-202
• /
• 2018

This paper studied the probability of pounding occurred between decks and abutments of a long span high-pier continuous rigid fame bridge subjected to ground motions with local soil effect. A pounding probability analysis methodology has been proposed using peak acceleration at bedrock as intensity measure (IM) for multi-support seismic analysis. The bridge nonlinear finite element (FE) models was built with four different separation distances. Effect of actual site condition and non-uniform spatial soil profiles on seismic wave propagating from bedrock to ground surface is modelled. Pounding probability of the high-pier bridge under multi-support seismic excitations (MSSE) is analyzed based on the nonlinear incremental dynamic analysis (n-IDA). Pounding probability results under uniform excitations (UE) without actual local site effect are compared with that under MSSE with site effect. The study indicates that the required design separation length between deck and abutment under uniform excitations is larger than that under MSSE as the peak acceleration at bedrock increases. As the increase of both separation distance between deck and abutment and the peak acceleration, the probability of pounding occurred at a single abutment or at two abutments simultaneously under MSSE is less than that under UE. It is of great significance considering actual local site effect for determining the separation distance between deck and abutment through the probability pounding analysis of the high-pier bridge under MSSE.

• 한국인터넷방송통신학회논문지
• /
• 제20권5호
• /
• pp.63-70
• /
• 2020

본 논문에서는 35 GHz 대역의 군 탐색기용 송수신 모듈을 설계 및 제작하였다. 밀리미터파 대역의 기판 성능과 집적도를 높이기 위해, 4층 액정 폴리머 기판을 개발하였다. 4층 액정 폴리머 기판은 3장의 FCCL 기판과 2장의 접착층으로 구현되었으며, 적층을 위해 기판간의 녹는 점 차이를 이용한 공정을 이용하였다. 스트립선로와 마이크로스트립 선로를 이용하여 기판의 길이에 따른 전송손실을 확인하였고, 35 GHz 대역의 전력분배기를 통해 액정폴리머 기판의 성능을 검증하였다. 이러한 기판을 이용하여 전력증폭기와 저잡음증폭기와 같은 송수신모듈을 구성하는 개별 블록에 대한 성능을 확인한 후, 단일 채널 Ka대역 송수신모듈을 4층 액정 폴리머 기판을 이용하여 개발하였다. 제작한 송수신모듈의 송신출력은 펄스 Duty 10%에서 1.1W 이상, 수신 잡음지수는 8.5 dB 이하, 수신 이득은 17.6 dB 이상의 수신 특성을 갖는다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2011년도 학술발표회
• /
• pp.15-15
• /
• 2011

The radar observation system in Japan is operated by two governmental groups: Japan Meteorological Agency (JMA) and the Ministry of Land, Infrastructure, Transport and Tourism (MLIT) of Japan. The JMA radar observation network is comprised of 20 C-band radars (with a wavelength of 5.6 cm), which cover most of the Japan Islands and observe rainfall intensity and distribution. And the MLIT's radar observation system is composed of 26 C-band radars throughout Japan. The observed radar echo from each radar unit is first modified, and then sent to the National Bureau of Synthesis Process within the MLIT. Through several steps for homogenizing observation accuracy, including distance and elevation correction, synthesized rainfall intensity maps for the entire nation of Japan are generated every 5 minutes. The MLIT has recently launched a new radar observation network system designed for flash flood observation and forecasting in small river basins within urban areas. It is called the X-band multi parameter radar network, and is distinguished by its dual polarimetric wave pulses of short length (3cm). Attenuation problems resulting from the short wave length of radar echo are strengthened by polarimetric wavelengths and very dense radar networks. Currently, the network is established within four areas. Each area is observed using 3-4 X-band radars with very fine resolution in spatial (250 m) and temporal (1 minute intervals). This study provides a series of utilization procedures for the new input data into a real-time forecasting system. First of all, the accuracy of the X-band radar observation was determined by comparing its results with the rainfall intensities as observed by ground gauge stations. It was also compared with conventional C-band radar observation. The rainfall information from the new radar network was then provided to a distributed hydrologic model to simulate river discharges. The simulated river discharges were evaluated again using the observed river discharge to estimate the applicability of the new observation network in the context of operations regarding flood forecasting. It was able to determine that the newly equipped X-band polarimetric radar network shows somewhat improved observation accuracy compared to conventional C-band radar observation. However, it has a tendency to underestimate the rainfall, and the accuracy is not always superior to that of the C-band radar. The accuracy evaluation of the X-band radar observation in this study was conducted using only limited rainfall events, and more cases should be examined for developing a broader understanding of the general behavior of the X-band radar and for improving observation accuracy.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.400-403
• /
• 2002

The fundamental experiments for measuring soft x-ray characteristics from the vacuum capillary are described. These experiments were primarily performed in order to generate line spectra such as x-ray lasers. The generator consists of a high-voltage power supply, a polarity-inversion ignitron pulse generator, a turbo-molecular pump, and a radiation tube with a capillary. A high-voltage condenser of 200 nF in the pulse generator is charged up to 20 kV by the power supply, and the electric charges in the condenser are discharged to the capillary in the tube after closing the ignitron. During the discharge, weakly ionized plasma forms on the inner and outer sides of a capillary. In the present work, the pump evacuates air from the tube with a pressure of about 1 mPa, and a demountable capillary was developed in order to measure x-ray spectra according to changes in the capillary length. In this capillary, the anode (target) and cathode elements can be changed corresponding to the objectives. The capillary diameter is 2.0 mm, and the length is adjusted from 1 to 50 mm. When a capillary with aluminum anode and cathode electrodes was employed, both the cathode voltage and the discharge current almost displayed damped oscillations. The peak values of the voltage and current increased when the charging voltage was increased, and their maximum values were -10.8 kV and 4.7 kA, respectively. The x-ray durations observed by a 1.6 ${\mu}$m aluminum filter were less than 30 ${\mu}$s, and we detected the aluminum characteristic x-ray intensity using a 6.8 ${\mu}$m aluminum filter. In the spectrum measurement, two sets of aluminum and titanium electrodes were employed, and we observed multi-line spectra. The line photon energies seldom varied according to changes in the condenser charging voltage and to changes in the electrode element. In the case where the titanium electrode was employed, the line number decreased with corresponding decreases in the capillary length. Compared with incoherent visible light, these rays from the capillary were diffracted and diffused greatly after passing through two slits.

• 한국항행학회논문지
• /
• 제6권1호
• /
• pp.44-51
• /
• 2002

무선 LAN(W-LAN)은 IEEE 802.11a, 802.11b의 표준이 제정됨에 따라 전송 속도도 수십 Mbps까지 고속으로 발전되어 왔고, 현재 여러 대학과 기업체에서 무선 LAN(W-LAN)을 많이 보급하고 있으며, 또한 통신 사업자들도 일부 제한된 지역(지하철 구내)에서 W-LAN을 설치하여 일반인에게 서비스하고 있다. 이와 같이 무선 LAN의 확산으로 서비스를 이용하는 사람들이 날로 증가 추세에 있으나 서비스 면에서 문제점들도 대두되고 있다. 특히 건물과 전파의 방해물이 많이 존재하는 도심 지역에서 데이터를 고속으로 전송하려면 상대적으로 주파수가 높아짐에 따라 무선 접속 장치(AP : Access Point)와 이동국(노트북등 단말기)간에 ISI(Inter Symbol Interference)가 발생하여 주파수 선택성 페이딩 채널 환경이 되어 데이터의 끊김과 에러가 발생하는 등 사용자에게 양질의 서비스를 제공하지 못하는 사례가 자주 있어 왔다. 본 논문에서는 다중 경로 채널 환경에서 ISI 영향을 가장 적게 받을 수 있는 OFDM 시스템을 적용하여 성능을 분석 평가 하였다. 데이터 변조 방식으로는 IEEE 802.11a에 근거한 부 반송파의 수가 52개인 BPSK, QPSK, 16QAM 방식을 적용하였고, 구속장이 7이고 부호율이 1/2, 3/4인 천공된 컨벌루셔널 부호를 사용하였으며 성능이 개선됨을 확인하였다. 특히 페이딩의 영향을 많이 받는 무선 채널 환경에서 단일 텝 등화기 및 결정 궤환 등화기(DFE : Decision Feedback Equalizer)를 적용하여 성능이 월등히 향상되고 단말기가 이동 시에도 데이터의 단절 등이 없음을 시물레이션을 통해 입증 하였다.

• 생물환경조절학회지
• /
• 제13권4호
• /
• pp.217-225
• /
• 2004

본 조사는 최근 급격히 증가하고 있는 새송이버섯 재배농가의 안정적 영농을 위해 재배사 설계, 시공 및 환경조절과 관련한 기초 자료를 마련하기 위해 서부 경남지역을 대상으로 새송이버섯 재배사의 재배사 규모, 환경조절시스템 등의 실태조사 및 검토를 하였다. 재배사의 형태는 반영구재배사와 영구재배사로 대별 할수 있었고, 반영구재배사는 대부분 단동이었고, 영구재배사의 경우는 단동에 비해 상대적으로 연동이 많았다. 그리고 재배사의 규모는 형태에 관계없이 다양하였지만, 길이, 폭 및 동고는 각각 20m, $6.6\~7.0m$ 및 $4.6\~5.0m$정도의 농가가 가장 많았으며, 동당 바닥면적은 $132\~140m^2$(40-42평)정도의 범위로서 대부분 콘크리트로 처리하여 각종 균에 의한 버섯의 오염을 방지 할 수 있도록 되어 있었다. 반영구 및 영구재배사의 지붕경사각은 각각 $41.5^{\circ}$ 및 $18.6\~28.6^{\circ}$로 나타나 반영구재배사의 지붕경사도가 더 큰 것으로 나타났다. 그리고 재배상의 폭 및 단수는 재배사의 형태에 관계없이 각각 $1.2\~1.6m$정도와 4단이 주류를 이루고 있었다. 버섯을 연중재배 하는 재배사에는 모두 냉${\cdot}$난방시설, 가습장치 및 환기팬이 설치되어 있었다. 난방방식의 경우, 온수보일러, 전기히터, 증기보일러 순으로 나타났다. 냉방장치의 경우는 모두 산업용 에어컨을 설치하여 운용하고 있었다. 그리고 가습은 초음파가습기와 원심분리가습기를 사용하고 있었으며, 보조 장치로 분무노즐을 사용하는 농가도 일부 있었다. 또한 온${\cdot}$습도 조절 및 탄산가스 조절을 위한 장치의 제어는 동별 제어시스템을 많이 채택하고 있었다. 그리고 온도센서 이외는 모두 타이머를 이용하고 있음을 알 수 있었다. 배지병의 크기는 850 cc 및 1,100 cc를 사용하는 농가가 주류를 이루고 있었고, 이 밖에도 800cc와 950 cc, 1,200 cc병을 사용하는 농가도 있었다. 출하형태는 대부분 유통회사와 공판장을 동시에 이용하고 있었다.