• Journal of Magnetics
• /
• v.20 no.2
• /
• pp.176-185
• /
• 2015

We present the design optimization of the magnetic pole and slot design options that minimize the cogging torque of permanent-magnet (PM) brushless generators for small wind turbine generators. Most small wind-turbines use direct-driven PM generators which have the characteristics of low speed and high efficiency. Small wind-turbines are usually self-starting and require very simple controls. The cogging torque is an inherent characteristic of PM generators, and is mainly caused by the generator's geometry. The inherent the cogging torque can cause problems during turbine start-up and cut-in in order to start softly and to run a power generator even when there is little wind power during turbine start-up. Thus, to improve the operation of small turbines, it is important to minimize the cogging torque. To determine the effects of the cogging torque reductions, we adjust the slot opening width, slot skewing, mounting method of magnets, magnet shape, and the opening and combinations of different numbers of slots per pole. Of these different methods, we combine the methods and optimized the design variables for the most significant design options affecting the cogging torque. Finally, we apply to the target design model and compare FEA simulation and measured results to validate the design optimization.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.15-16
• /
• 2008

In case manufacturing COF, through hole should be made to be used for a pathway connecting the conductive layers of its both faces. In case Cu-plating inside of through hole with electroless plating way, contact between Cu and PI film gets bad to be fell apart from PI by the impact of applying to the electric devices. Therefore, after sputtering is applying on inner through hole, then a method to perform electroplating process. In this study, after changing sputtering condition to manufacture FCCL, we looked the changeability of the upper PI and inner hole Cu layers. Making use of RF Magnetron sputtering equipment, we coated Cu thin film and Cu-plated on it through electroplating. After cold-mounting the completed FCCL, we examined hole section through an optical microscope. From the result of test, with parameters deposition pressure and deposition time, both the thickness of the hole plated layer and PI plated upper layer increased at regular rate, increasing the thickness of Cu sputter layer. However, from the result of test in increasing RF-power, we could know the increment rate of hole plated layer is considerably greater than that of PI plated upper layer. Therefore, we finally acquired good result; if you want only to increase the plated layer of inner hole, it's much better to increase RF-power.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.3
• /
• pp.281-287
• /
• 2016

The purpose of this study is to analyze the vibration characteristics and develop a mounting which can improve the strength safety factor to replace the high failure rate APU(auxiliary power unit) imported metal mounts with rubber mount that can be domestically produced. For this study, we analyzed in 3 kinds of rubber mounts hardness for the natural frequency to avoid the average excited frequency of the APU. In addition, allowed vibration acceleration of rubber mount confirmed to 90.8 g by adding a strength safety factor. To assure the validity of the design, we measure the vibration acceleration equipped with a metal mount and rubber mount 2 species(Hs 50 and 60). As a result, the proposed design method in this study is reasonable because the rubber mounts is excellent strength safety factor and vibration transmissibility than metal mounts.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.86-93
• /
• 1996

The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• Korean Journal of Optics and Photonics
• /
• v.22 no.3
• /
• pp.141-150
• /
• 2011

Although significant amount of research has been done to develop LED lamp packages for improved performance, no standard theories or guidelines have been established yet for designing LED lamp packages. In this paper, the photon extraction efficiency depending on both the InGaN/Sapphire LED chip structure and its attachment schemes for chip mounting has been analyzed by using the Monte Carlo photon simulation method. Based on the results of the analysis, we have derived guidelines for LED lamp package design, which can be utilized in industries or research institutes for designing new LED lamp packages optimized for particular applications.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.527-536
• /
• 2021

In wireless environments, wideband receivers are used in a communication intelligent system to detect unknown signals and obtain azimuth information. To design a wideband receiver that performs multiple signal detection and direction finding simultaneously, it is necessary to consider a reception structure composed of multiple channels. In this paper, we propose a wideband multi-channel receiver for direction finding of unknown wideband communication signals including frequency hopping signals. A signal processing method for detecting received signals and estimating azimuth information is presented, and components of the manufactured wideband receiver are described. In addition, test results of the signal detection performance by mounting the proposed wideband multi-channel receiver on the flight system are included.

• Journal of Fashion Business
• /
• v.22 no.5
• /
• pp.125-136
• /
• 2018

This study intended to develop a motorcycle safe vest that can be prepared against accidents by mounting a smart module (with built-in sensor) on the safe vest in order to emphasize safety among functional aspects of the motorcycle clothing. The research method investigated professional books, prior research, and Internet data to examine the characteristics of motorcycle wear and the theoretical examination of smart wear, and analyzed the functional characteristics of the design by reviewing smart jacket and vest design cases for motorcycles currently on the market. As a results of study an interface device sensor, which contains a sensor with IMU(Intertial Measurement Unit) and CPU(Central Processing Unit), was inserted into a motorcycle top in order to draw attention to the safety of motorcycle riders. The IMU sensor attached to the vest detected the tilting motion of the rider to either left or right side to obtain data on left or right direction, sudden stop, and so forth and displayed left or right turn signal and sudden stop sign on the backplate (back) through the LED module. As for charging the device to operate LEDs, a generator, which is designed to convert the heat energy in the exhaust into electric energy, was used to efficiently self-produce the power required to operate LEDs of the top while riding.

• Journal of Space Technology and Applications
• /
• v.3 no.4
• /
• pp.322-332
• /
• 2023

Satellite attitude-control actuators are equipped with a reaction wheel for three-axis attitude control. The reaction wheel rotates a motor inside the actuator to generate torque in the vector direction. When using the reaction wheel, there are restrictions on the torque values generated as the motor rotates. The torque value of the reaction wheels mounted on small satellites is approximately 10 mNm, and high values are not used. Therefore, three-axis attitude control of a small satellite is possible using a reaction wheel, but this method is not suitable for missions that require rapid attitude control at a specific time. As a technology to overcome the small torque value of the reaction wheel, the control moment gyro (CMG) is currently in wide use as a rapid attitude-control actuator in space satellites. The CMG has an internal gimbal mounted at a right angle to the rotation motor and generates a large torque value. In general, when the gimbal operates, a torque value approximately 100 times greater is generated, making it suitable for rapid posture maneuvering. Currently, we are developing a technology for mounting a controlled moment gyro on a small satellite, and here we share the development status of an 800 mNm CMG.

• Smart Structures and Systems
• /
• v.33 no.1
• /
• pp.27-39
• /
• 2024

The effectiveness of conventional tuned liquid dampers (TLDs) in controlling the wind-induced response of tall flexible structures has been indicated. However, the impaired control effect in the detuning condition or a considerably high mass cost of liquid may be incurred in ensuring the high-level serviceability. To provide an efficient TLD-based solution for wind-induced vibration control, this study proposes a serviceability-oriented optimal design method for isolated TLDs (ILDs) and derives analytical design formulae. The ILD is implemented by mounting the TLD on the linear isolators. Stochastic response analysis is performed for the ILD-equipped structure subjected to stochastic wind and white noise, and the results are considered to derive the closed-form responses. Correspondingly, an extensive parametric analysis is conducted to clarify a serviceability-oriented optimal design framework by incorporating the comfort demand. The obtained results show that the high-level serviceability demand can be satisfied by the ILD based on the proposed optimal design framework. Analytical design formulae can be preliminarily adopted to ensure the target serviceability demand while enhancing the structural displacement performance to increase the safety level. Compared with conventional TLD systems, the ILD exhibits higher effectiveness and a larger frequency bandwidth for wind-induced vibration control at a small mass ratio.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.2
• /
• pp.437-444
• /
• 2024

The rotational inertial navigation system can provide more accurate navigation information by mounting an IMU (Inertial Measurement Unit) on the gimbal and rotating the gimbal regularly to cancel out the errors of the IMU. However, when an attitude change occurs due to waves, the attitude error is not removed to 0 at the end of one cycle of the rotation procedure and causes a large position error. In this paper, considering this problem, we propose a method of stabilizing the external gimbal by rotating it based on the roll information of the vehicle. Based on simulation, the impact of waves is analyzed and the performance of external gimbal stabilization is verified.