• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.527-536
• /
• 2021

In wireless environments, wideband receivers are used in a communication intelligent system to detect unknown signals and obtain azimuth information. To design a wideband receiver that performs multiple signal detection and direction finding simultaneously, it is necessary to consider a reception structure composed of multiple channels. In this paper, we propose a wideband multi-channel receiver for direction finding of unknown wideband communication signals including frequency hopping signals. A signal processing method for detecting received signals and estimating azimuth information is presented, and components of the manufactured wideband receiver are described. In addition, test results of the signal detection performance by mounting the proposed wideband multi-channel receiver on the flight system are included.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1169-1176
• /
• 2018

The C-band omni-directional antenna for drone control is mounted on the top or bottom and used to configure the communication link. The communication link is affected by the LOS depending on the mounting position of the omni-directional antenna. In this paper, two kinds of embedded antennas were designed with a commercial simulation tool CST MWS, and EM analysis was performed to consider the mounting environment. Also, we propose the PTMP ground antenna to control a large number of drones. The ground antenna has a communication link of 30km, and it consists of four sector antennas in the horizontal direction and one directional antenna at the top.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.8
• /
• pp.1110-1116
• /
• 2021

In this paper, we propose a conformal Ku-band data link antenna to ensure low RCS of stealth UAV. As a phased array antenna with electrical beam steering function, a transmitter and a receiver were designed and manufactured for FDD communication, respectively. Each antenna is designed as a 12*12 planar array antenna and has a function to form a uni-directional pattern and a bi-directional pattern through phase control of unit elements. The beam steering range is designed to be able to steer up to 60 degrees in theta direction and 360 degrees in the phi direction. As a result of manufacturing and measurement, the conformal type radome has low transmission loss and meets the required specifications including system performance. The feasibility of mounting the stealth UAV has been confirmed, and future research directions such as interworking of baseband devices and conversion to digital beam steering function are suggested.

• Journal of Wind Energy
• /
• v.4 no.2
• /
• pp.34-39
• /
• 2013

The wind resource assessment for measured wind data over 1 year by using the meteorological mast should be a prerequisite for business feasibility of the wind farm development. Even though the direction of boom mounting the wind vane and anemometer is carefully engineered to escape the interference of wakes generated from the met-mast structures, the shadow effect is not completely avoided due to seasonal winds in the Korean Peninsula. The shadow effect should be properly calibrated because it is able to distort the wind resources. In this study a calibration method is introduced for the measured wind data at Julpo in Jeonbuk Province. Each sectoral terrain conditions along the selected wind direction nearby the met-mast is investigated, and the distorted wind data due to shadow effects can be calibrated effectively. The correction factor is adopted for quantitative calibration by carrying out the WindSim analysis.

• Journal of Navigation and Port Research
• /
• v.36 no.5
• /
• pp.357-361
• /
• 2012

Anemometer is a meteorological instrument that measures wind direction and wind speed in real time, and is mounted to the cranes that are used at ports, shipbuilding yards, off-shore structure, or construction sites that are influenced by wind, and it is used in conjunction with the safety system. Load cell-type anemometer measures the wind direction through the ratio of load between 4 positions by mounting the thin plate to 4 load cells, and measures wind velocity through the summation of loads. In this study, we compared and analyzed the results in the theoretic approach, analytic approach and experimental approach to derive the correlation between load ratio and wind direction. Wind direction was selected as the design variable, and selected 9 wind direction conditions from $0^{\circ}{\sim}90^{\circ}$ with $11.25^{\circ}$ space for analysis, and 10 wind direction conditions with $10^{\circ}$ space for experiment.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.5
• /
• pp.49-53
• /
• 2015

Thrust vector control is the method which generates the side force and roll moment by controlling exhausted gas directly in a rocket nozzle. TVC is classified by mechanical and fluid dynamic methods. Mechanical methods can change the flow direction by several objects installed in a rocket nozzle exhaust such as tapered ramp tabs and jet vane. Fluid dynamic methods control the flight direction with the injection of secondary gaseous flows into the rocket nozzle. The tapered ramp tabs of mechanical methods are used in this paper. They installed at the rear in the rocket nozzle could be freely moved along axial and radial direction on the mounting ring to provide the mass flow rate which is injected from the rocket nozzle. TVC of the tapered ramp tabs has the potential to produce both large axial thrust and high lateral force. We have conducted the experimental research and flow analysis of ramp tabs to show the performance and the structural integrity of the TVC. The experiments are carried out with the supersonic cold flow system and the schlieren graph. This paper provides to analyze the location of normal shock wave and distribution of surface pressure on the region enclosed by the tapered ramp tabs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.766-773
• /
• 2016

This paper proposes an aircraft-installed compact offset-parabolic-reflector antenna for the spinning direction-finding applications. The feeder of the reflector antenna is a LPDA antenna that has the ultra-wideband characteristics and the $45^{\circ}$ slant linear polarization. The reflector is designed to be slanted by $5^{\circ}$ in the elevation and to be small in size on the basis of the reference parabolic shape for the purpose of the high gain and mounting on the underside of aircraft fuselage. Over the ultra-wideband 20:1 bandwidth from S to Ka band, the measured average gain of the proposed antenna is 27.97 dBi, and the average half-power beam width is $4.55^{\circ}$ in the azimuth and $4.3^{\circ}$ in the elevation which is the pencil-beam radiation pattern. All the measured data are similar to the simulation results. The designed compact offset-parabolic-reflector antenna that is installed in the limited area has the ultra-wideband and high-gain characteristics. We expect that the newly designed antenna can be applied to the spinning direction-finding antenna system installed in an aircraft.

• Agribusiness and Information Management
• /
• v.12 no.1
• /
• pp.36-49
• /
• 2020

This study pertains to direction of exports direction of major agricultural commodities viz., rice, maize, bengal gram, chillies and cotton from India. In the ensuing next decade during 21st century, India is likely to witness changes in the export pattern of these commodities due to both internal and external constraints. One of the major internal constraints is mounting cost of production. Similarly, one of the most important external constraints include excessive subsidization by importing countries that makes Indian commodities less competitive in the international market. So, the important research question is to analyse the direction of exports of major agricultural commodities from India during post-WTO regime. The dynamic nature of trade pattern of the selected commodities was analyzed by employing the first order Markov process by examining gains and losses in respect of export shares of major Indian agricultural commodities to different countries. During the post-WTO regime, it was found that Saudi Arabia for rice, Bangladesh for maize, Pakistan for bengal gram, Malaysia for (dry) chillies, China, mainland for cotton are the loyal destinations for the commodities. The increasing demand for the selected commodities in countries like Saudi Arabia, Côte d'Ivoire for rice; Malaysia for maize; Pakistan and Algeria for Bengal gram; USA and Sri Lanka for (dry) chillies and Vietnam, Pakistan and Indonesia for cotton need to be explored for augmenting the exports. In order to achieve this goal, it is essential that consumer preferences in newer markets, market intelligence and impediments for augmenting exports need to be researched. It is also high time to analyze the export competitiveness of selected commodities across these importing countries.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2064-2071
• /
• 2020

For proton pencil beam scanning (PBS) technology, the accuracy of the dose distribution in a patient is sensitive to the properties of the incident beam. However, mechanical deformation of the proton therapy facility may occur, and this could be an important factor affecting the proton dose distribution in patients. In this paper, we investigated the effect of deformation on an SC200 proton facility's beam isocenter properties. First, mechanical deformation of the PBS nozzle, L-shape plate, and gantry were simulated using a Finite Element code, ANSYS. Then, the impact of the mechanical deformation on the beam's isocenter properties was evaluated using empirical formulas. In addition, we considered the simplest case that could affect the properties of the incident beam (i.e. if only the bending magnet (BG3) has an error in its mounting alignment), and the effect of the beam optics offset on the isocenter characteristics was evaluated. The results showed that the deformation of the beam position in the X and Y direction was less than 0.27 mm, which meets the structural design requirements. Compared to the mechanical deformation of the L-shape plate, the deformation of the gantry had more influence on the beam's isocenter properties. When the error in the mounting alignment of the BG3 is equal to or more than 0.3 mm, the beam deformation at the isocenter exceeds the maximum accepted deformation limits. Generally speaking, for the current design of the SC200 scanning beam delivery system, the effects of mechanical deformation meet the maximum accepted beam deformation limits. In order to further study the effect of the incident beam optics on the isocenter properties, a fine-scale Monte Carlo model including factors relating to the PBS nozzle and the BG3 should be developed in future research.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.31 no.1
• /
• pp.26-32
• /
• 2015

Purpose: The main purpose of this study is to suggest application plan of dipping method by comparing & analysing the difference between addition method and dipping method in the manufacture of metal-ceramic substructure of maxillary central incisor (#1), followed by assessing the work efficiency. Materials and Methods: Master die and hard plaster-copied one were produced and then a total of 20 copies, 10 copies for each through addition method and dipping method, were manufactured and experimented. Copings were fixed on the abutment model and invested in epoxy mounting cup. Samples were cut in labial and lingual direction, using cutter and then rubbed on sandpaper, whose 4 points were measured by using digital microscope. Results: The comparison of mean values by using t-test, parametric statistical method, shows overall significant difference (P < 0.05). Conclusion: The result of this study can be suggested as an application plan, since there is no significant difference between addition method and dipping method in the manufacture of metal-ceramic substructure.