• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.181-186
• /
• 2010

A numerical study was conducted to predict the performance curve of a canned motor pump for SMART(System Integrated Modular Advanced ReacTor). The study used a computational domain which included not only the pump but also a suction pipe and a volute casing with a discharging pipe in order to simulate an experimental setup. The ANSYS CFX program was utilized to obtain flow characteristics inside the pump as well as the overall pressure rise across the pump operating on- and off-design points. Computed results showed that the performance of the pump at off-design points was much lower than expected. Special attention was made to find the cause of the low performance of the pump operating at low flow rate.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.392-398
• /
• 2005

This paper presents technologies that have strategic importance in future motor drives. The underlying strategic issue for motor drives is maintaining cost while increasing certain dimensions of functionality. The dimensions of functionality which should increase include reliability and added value features such as providing continuous energy optimization, providing sensing of the driven system suitable for application specific diagnostic purposes, and providing continuously optimal thermal utilization of the capability of the drive. This paper will address each of these issues and discuss the technology status for each case, with a focus on research needed to fully deliver the needed functionality.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.1038-1046
• /
• 2004

In order to acquire high-speed and high-precision performances in servomechanisms, an integrated design method have been proposed. Based on strict mathematical modeling and analysis of system performance according to design and operating parameters, a nonlinear constrained optimization problem including the relevant subsystem parameters of the servomechanism is formulated. Optimum design results of mechanical and electrical parameters are obtained according to the design parameters specified by designers through the integrated design processes. Motors are optimally selected from the servo motor database. Both the geometric errors referring to Abbe offset and the contour errors are minimized while required constraints such as stability conditions and saturated conditions are satisfied. This design methodology both offers the improved possibility to evaluate and optimize the dynamic motion performance of the servomechanism and improves the quality of the design process to achieve the required performance for high-speed/precision servomechanisms.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.527-532
• /
• 2011

Due to the need for improved fuel consumption and the trend towards increasing the electrical content in automobiles, integrated starter generator (ISG) systems are being considered by the automotive industry. In this paper, in order to change the conventional generator of a vehicle, a belt driven integrated starter generator is considered. The overall ISG system, the design considerations for the claw pole type AC electric machine and a low voltage very high current power stage implementation are discussed. Test data on the low voltage claw pole type machine is presented, and a large current voltage source DC/AC inverter suitable for low voltage integrated starter generator operation is also presented. A metal based PCB (Printed Circuit Board) power unit to attach the 4-parallel MOS-FETs is used to achieve extremely high current capability. Furthermore, issues related to the torque assistance during vehicle acceleration and the generation/regeneration characteristics are discussed. A prototype with the capability of up to 1000 A and 27 V is designed and built to validate the kilo-amp inverter.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.73-76
• /
• 2002

In this paper we present an integrated Hail sensor It for fan motors, fabricated in industrial bipolar process. As a discrete Hall sensor and signal processing circuitry In the fan motor system were Integrated into single chip a temperature dependence of Hall sensitivity and Hall offset voltage can be compensated and cancelled by on-chip circuitry. We Propose a novel temperature compensation of Hall sensitivity with negative temperature coefficient (TC) using the differential amplifier gain with Positive TC. After a package of the chip was sealed using a plastic Package 20 Pins, the thermal and magnetic characteristics were investigated. The obtained experimental results are in agreement with analytical predictions and have more excellent performance than\ulcorner conventional the fan motor system using discrete Hall sensor.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권1호
• /
• pp.32-39
• /
• 2014

Traveling wave generation in a ring type stator has been studied. The basic working principle to create traveling wave has been modelled by the superposition of two orthogonal standing waves. Theoretical analysis shows that the length to radius ratio affects the frequency gap between two pseudo orthogonal modes used to create traveling wave. FEM simulation is then discussed and applied to validate the analytical model. At last, a possible optimal solution is reported with FEM verification.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.93-97
• /
• 2005

This paper proposes a design of stepper motor control in microstep driven mode using FPGA (Field Programmable Gate Array) for hardware implementation. The methods to drive stepper motor in microstep excitation mode are to control of the controlling currents in each phase windings of stepper motor with reference signals. These reference signals are used for controlling the current levels, the required variation of current levels with rotor position can be obtained from the ideal linear or sinusoidal approximations to the static torque-displacement ($T-{\theta}$) characteristic curve. In addition, the hardware implementation of stepper motor controller can be designed uses VHDL (Very high speed integrated circuits Hardware Description Language) and synthesis using an Altera FPGA, FLEX10K family, EPF10K20RC240-4 device as target technology and use MAX+PlusII program for overall development. A multi-stack variable-reluctance stepper motor of Sanyo Denki is used in the experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.193-196
• /
• 2001

In this paper we designed CAMC-SP, the microprocessor embedded 2-axis motor control chip which controls a precise pulse motor by generating the pulse needed to control step motor, DC servo and AC servo motor. This design enables to decrease costs and to minimize a size. First we designed risc type 8-bit microprocessor compatible with PIC16C84, second we designed pulse motor controller. CAMC-SP is integrated of those two block. We designed CAMC-SP by VHDL and we testified to the Performance of it by performing functional simulation.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권5호
• /
• pp.320-326
• /
• 2000

The canned motor of 3-phase induction is used for main coolant pump(MCP). The type of motor is canned-motor that stator and rotor are welded by sealed can. So, cooling water flows in the air gap of the canned motor as an independent cycling cooling system from the air gap to yoke of the motor to prevent high temperature of stator can and to lubricate bearing. Heat exchange is occurred between cooling water in the air gap and cooling water from the exterior pump to prevent rising of temperature in the motor. I has to analyze the characteristics of can exactly because the loss and the heat in the can are very important to design MCP. Therefore, thermal analysis is studied considering the effect of eddy-current los induced in the can.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권1호
• /
• pp.16-20
• /
• 2006

The proposed paper presents an integrated linear actuator which combines Transverse Flux Linear Motor(TFLM) for Household elelctric applications. They both use the same primary magnetic circuit, but they have different secondary movers. The paper presents a new design of linear motor for a new electromagnetic linear actuator, an tintegrated TFLM. The calculated tthrust force is good agreement with experiments. We have studied a transient response of a linear actuator with a damping ratio, spring constant and specially a pressed power patterns for a constant stroke control.