• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.606-611
• /
• 2007

Pulsation is an inherent phenomenon in reciprocating compressors. It interacts with piping to cause vibrations and performance problems. Indiscriminately connecting to a compressor can be dangerous and cost money in the form of broken equipment and piping, poor performance, inaccurate metering, unwanted vibration, and sometimes noise. Piping connected to a compressor can materially affect the performance and response. To minimize these detrimental effects, reciprocating compressor system should be equipped by pulsation suppression system. This study discusses pressure pulsation phenomena occurred in a reciprocating compressor system. An experiment applied air compressor unit, as pulsating pressure generator, has been done. The compressor was connected sequentially to a snubber model and pressure tank. Sensor probes were placed on the inlet and outlet pipes of snubber. Compressor was driven by a motor controlled by a frequency regulator. The experiment was conducted by adjusting the regulator at 40Hz. General information about an internal gas flow can be achieved by numerical analysis approach. Information of the velocity, pressure and turbulence kinetic energy distribution are presented in this paper. Based on this result, the design improvement might be done.

• 전력전자학회논문지
• /
• 제8권6호
• /
• pp.478-487
• /
• 2003

본 논문에서는 고압 대용량 전동기 구동용 멀티레벨 인버터의 종류 및 특징을 간략히 살펴보고, 특히 입출력 전력품질이 우수하고 전압별 시리즈화가 용이한 H-브릿지 멀티레벨 인버터의 구조적 특징 및 장점을 기술하였다. 연구 개발된 3,300V lMVA 용량의 Cascaded H-브릿지 멀티레벨 인버터의 구체적인 전력회로 구조 및 설계방법, 제어기 구성 그리고 PWM 기법을 제시하였다. 또한, 실용량의 시험을 통해 H-브릿지 멀티레벨 인버터는 출력 전압 Step이 여러 단계이고 dv/dt가 적으며 입력단 THD를 크게 낮출 수 있어 성능 면에서도 여타 방식보다 우수함을 입증하였다. 또한 생산적인 측면에서도 저압 소자를 사용하여 설계하므로 기존의 생산/시험 기술과 설비를 이용할 수 있어 매우 경제적이며 Power Cell 단위 결합 구조이므로 신뢰성 측면이나 보수/유지 측면에서도 유리하다는 결론을 얻었다.

• The Korean Journal of Pain
• /
• 제26권1호
• /
• pp.39-45
• /
• 2013

Background: Good postoperative pain control is an important part of adequate postoperative care. Patient-controlled epidural analgesia (PCEA) provided better postoperative analgesia compared to other conventional analgesic methods, but several risks have been observed as well. We therefore surveyed the efficacy and safety of PCEA in this retrospective observational study. Methods: We analyzed collected data on 2,276 elective surgical patients who received PCEA with ropivacaine and fentanyl. Patients were assessed by a PCA service team in the post-anesthesia care unit (PACU), at 1-6 h, 6-24 h, and 24-48 h postoperatively for adequate pain control. The presence of PCEA-related adverse events was also assessed. Results: Numerical pain score (median [interquartile range]) were 3 [1-4], 5 [4-7], 4 [3-5], and 3 [3-5] in the PACU, at 1-6 h, 6-24 h, and 24-48 h postoperatively. Median pain scores in patients underwent major abdominal or thoracic surgery were higher than other surgical procedure in the PACU, at 1-6 h after surgery. Nausea and vomiting (20%) and numbness and motor weakness (15%) were revealed as major PCEA-related adverse events during the postoperative 48 h period. There were 329 patients (14%) for whom PCEA was ceased within 48 h following surgery. Conclusions: Our data suggest that the use of PCEA provides proper analgesia in the postoperative 48 h period after a wide variety of surgical procedures and that is associated with few serious complications. However, more careful pain management and sustainable PCEA monitoring considering the type of surgical procedure undergone is needed in patients with PCEA.

• Clinical and Experimental Pediatrics
• /
• 제64권7호
• /
• pp.313-321
• /
• 2021

Here we describe the neurodevelopmental outcomes of very low birth weight (VLBW) infants (birth weight ≤1,500 g) at 3 years of age in the Neonatal Research Network of Japan (NRNJ) database in the past decade and review the methodological issues identified in follow-up studies. The follow-up protocol for children at 3 years of chronological age in the NRNJ consists of physical and comprehensive neurodevelopmental assessments in each participating center. Neurodevelopmental impairment (NDI)-moderate to severe neurological disability-is defined as cerebral palsy (CP) with a Gross Motor Function Classification System score ≥2, visual impairment such as uni- or bilateral blindness, hearing impairment requiring hearing amplification, or cognitive impairment with a developmental quotient (DQ) of Kyoto Scale of Psychological Development score <70 or judgment as delayed by pediatricians. We used death or NDI as an unfavorable outcome in all study subjects and NDI in survivors using number of assessed infants as the denominator. Follow-up data were collected from 49% of survivors in the database. Infants with follow-up data had lower birth weights and were of younger gestational age than those without follow-up data. Mortality rates of 40,728 VLBW infants born between 2003 and 2012 were 8.2% before discharge and 0.7% after discharge. The impairment rates in the assessed infants were 7.1% for CP, 1.8% for blindness, 0.9% for hearing impairment, 15.9% for a DQ <70, and 19.1% for NDI. The mortality or NDI rate in all study subjects, including infants without follow-up data, was 17.4%, while that in the subjects with outcome data was 32.5%. The NRNJ follow-up study results suggested that children born with a VLBW remained at high risk of NDI in early childhood. It is important to establish a network follow-up protocol and complete assessments with fewer dropouts to enable clarification of the outcomes of registered infants.

• 전기전자학회논문지
• /
• 제23권1호
• /
• pp.254-260
• /
• 2019

본 논문에서는 양방향 dc-to-dc 컨버터의 고장원인, 고장영향, 고장 결과를 파악하기 위한 failure mode and effect analysis(FMEA)와 양방향 컨버터의 위험도를 고려한 fault-tree analysis(FTA)를 통해 고장률을 예측한다. 전기차의 구동전압을 효율적으로 상승시키기 위해 인버터 앞단에 부착되는 양방향 컨버터는 배터리 전력을 dc-link 커패시터로 방전시키는 승압모드와 회생전력을 배터리로 충전시키는 강압모드를 가진다. 양방향 컨버터의 동작 특성을 고려한 FMEA 결과를 바탕으로 컨버터의 위험도를 고려한 고장나무를 설계한다. 전기차 MCU용에 맞는 설계 파라메타를 설정하고 출력전압 리플과 인덕터 전류 리플에 따른 커패시터와 인덕터의 부품 고장률을 분석한다. 또한 동작 온도에 따른 주요부품의 고장률을 MIL-HDBK-217F를 이용하여 구한다. 마지막으로 부품 고장률을 고장나무의 기본 사상의 고장률로 반영하여 컨버터 고장률과 평균고장시간을 예측한다.

• 한국기계가공학회지
• /
• 제18권3호
• /
• pp.33-40
• /
• 2019

FDM 3D printers have become widespread, and investment in the 3D printer industry is increasing. Therefore, many 3D printers are released and the functions of products are emphasized. However, to lower unit prices, open-type 3D printers are sold in kit form, and their performance is very low. If the 3D printer has many heat sources and is sealed, there is the possibility that the main accessories (the main board, power supply, and motor) will be damaged by trapped heat. At the same time, if the ambient temperature is low due to the properties of the material, the output quality deteriorates. In this study, we analyzed the temperature rise of the main accessories and the quality of the output by the heat bed when a chamber was added to an open-type 3D printer. We also compared the quality of the output due to the air flow with the temperature rise of the main accessories. Moreover, we found the optimal value. As a result of the quality analysis, it was finally confirmed that the case with the chamber at $95^{\circ}C$ was the best for the printing condition. In addition, in the absence of the chamber, the bending of the specimen was found to be large, and in the case of the chamber, the degree of bending was slightly decreased by 0.05 mm.

• Neonatal Medicine
• /
• 제25권4호
• /
• pp.178-185
• /
• 2018

Purpose: We aim to assess the Bayley Scales of Infant and Toddler Development, third edition (Bayley-III), Adaptive Behavior (AB) and Social-Emotional (SE) scales at 18 to 24 months of corrected age (CA) to examine their associations with school-age cognitive and behavioral outcomes in children born preterm. Methods: Eighty-eight infants born with a very low birth weight (<1,500 g) or a gestational age of less than 32 weeks who were admitted to the neonatal intensive care unit from 2008 to 2009 were included. Of the 88 children who completed school-age tests at 6 to 8 years of age, 37 were assessed using the Bayley-III, including the AB and SE scales, at 18 to 24 months of CA. Correlation, cross-tabulation, and receiver operating characteristic analyses were performed to assess the longitudinal associations. Results: A significant association was observed between communication scores on the Bayley-III AB scale at 18 to 24 months of CA and the Korean version of the Wechsler Intelligence Scale for Children (K-WISC) full-scale intelligence quotient (FSIQ) at school age (r=0.531). The total behavior problem scores of the Korean version of the Child Behavior Checklist (K-CBCL) at school age were significantly negatively related to the Bayley-III SE and AB scales but not to the cognitive, language, or motor scales. Conclusion: Our findings encourage AB and SE assessments during the toddler stage and have important implications for the early identification of children in need of intervention and the establishment of guidelines for follow-up with high-risk infants.

• 한국항공우주학회지
• /
• 제50권10호
• /
• pp.691-699
• /
• 2022

본 논문에서는 대형 메쉬 안테나 개발을 위한 모듈식 전개형 반사판 및 붐 구조의 전개 시 요구되는 구동력 및 전개 특성을 분석하고자 한다. 단위 전개 구조를 이용하여 모듈식 전개형 반사판 링과 붐 구조의 수납/전개된 형상을 분석하였다. Kane's 방정식을 이용하여 전개 구조물의 다물체 동역학 방정식을 유도하고 PUTD(Pseudo Upper Triangular Decomposition) 방법을 적용하여 구속조건 문제를 해결하였다. 다물체 동역학 시뮬레이션을 통해 설계된 모듈식 전개 반사판 링 그리고 붐 구조의 동적 특성을 살펴보고자 한다.

• 한국가스학회지
• /
• 제26권2호
• /
• pp.9-13
• /
• 2022

벨트나 체인을 이용한 감속기는 간단한 장치이긴 하지만 공간을 많이 차지하여 공간상의 제약이 있기 때문에 전동휠체어 구동부에는 부적합하다. 하지만 유성기어형태의 감속기는 동일 축에서 감속이 이루어지기 때문에 부피를 작게 할 수 있어 공간의 제약이 벨트나 체인형태의 감속기보다 덜하다. 따라서 본 연구에서는 수·전동전환이 가능한 휠체어의 구동부에 대한 연구를 통하여 유성기어형태를 이용한 감속기로 큰 추진력을 얻을 수 있는 구동부를 개발하였다. 그에 따라 감속기에 적용되는 유성기어의 치형을 Kisssoft 프로그램을 이용하여 설계를 진행하였다. 또한 기존 휠체어 바퀴에 적용 가능하도록 구동부의 설계를 진행하였고, 구동부의 수·전동 전환원리 및 작동원리에 대한 메커니즘의 최적화를 진행하였다. 연구내용을 토대로 하나의 선기어와 2개의 유성기어, 하나의 링기어를 갖는 유성기어 형태의 휠체어 감속기 구동부의 최종 설계 및 제작을 진행하였다.

• 한국정보전자통신기술학회논문지
• /
• 제17권3호
• /
• pp.141-145
• /
• 2024

근피로로 인해 운동단위들의 모집과 발화율이 감소하므로 근전도 전력스펙트럼이 낮은 주파수로 전이되는 스펙트럼 압축을 나타나며 이로 인해 중앙주파수가 낮아진다. 그러나 중앙주파수의 변화는 저주파수 대역의 크기 변화보다 상대적으로 미약한 변화를 보인다. 본 연구에서는 이미 제안된 주파수 대역의 범위 중에서 대퇴이두근의 스펙트럼 피로지수로서 적당한 주파수 대역의 범위를 통계적으로 선택하고자 한다. 실험에 참여한 피검자의 수는 12명이며, 4.5 km/h의 속도로 트레드밀 보행시 대퇴이두근의 근전도를 측정하였다. 근전도의 중앙주파수를 기준으로 저역 및 고역 주파수 대역의 크기들을 ANOVA 분석으로 비교하였다. 그 결과 저주파수 대역 25-82Hz과 고주파수 대역 142-300Hz가 대퇴이두근의 근피로지수로서 적당함을 확인하였다.