• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2007.04a
• /
• pp.283-288
• /
• 2007

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.288-291
• /
• 2001

In steel plant, load torque of mill driver motor is changed periodically because working state and idle state are repeated and load current of working state is necessarily higher than rated motor current. The over current limiter is one of the basic thermal protection method from over heating. In this paper, we analyzed the structure of over current limiter for motor and motor driver systems, developed over current limiter with same operation and structured warning system of action of over current limiter. As using this warning system, we can avoid abrupt plant stop by over current limiter in mill driver and lessen producing loss by plant stop. The developed warning system of action of over current limiter is exactly inspected by computer simulation md analysis of acquired data.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.4
• /
• pp.653-659
• /
• 2015

In the last few years, the regulations for efficiency grade of the three phase induction motor are internationally being discussed and upgraded for the protection of environment and energy saving. So the efficiency improvement and the reliable test result are essential to determine the premium grade three phase induction motor. While a study on developing the efficiency motor is active, there is little research about the guarantee for efficiency. So in this paper, the dispersion characteristic of the efficiency is studied using uncertainty theory for the three phase induction motor to improve the reliability of efficiency. The values such as input voltage, current, speed, torque were obtained by loss separation method to evaluate the uncertainty. From the result, it was known that the important loss factor could affect the uncertainty is the stray loss.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.167-174
• /
• 1997

In this paper, the mathematical model of the hydraulic control valve is formulated, that is, this dynamic modeling which includes the motion equations and continuity equations can analyze the dynamic characteristics of the hydraulic control valve. The control valve for the transmission has the Over Speed Protection to protect a hydraulic travel motor. Therefore, this simulation shows the over speed protection and researches the main design parameters. The results of the computer simulation were assured through the experiment. From the comparison between both results, it is shown that this simulation program is useful and effective.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.49-57
• /
• 2008

The performance of crash cushion systems is certified through the full scale crash tests by the standard for installation and maintenance guidelines for roadside safety appurtenance. The impact severities of impacting vehicles in collision with crash cushion systems are rated by indices THIV and PHD. Crash test results are considered to study the performance of three crash cushion systems. In case of the frontal impact or the offset frontal impact, the results show that THIV values of three systems are very close to the threshold limit for the occupant protection. Also, the results show that PHD would be improper for the occupant protection performance index. In order to improve the occupant protection performance of crash cushions, ASI needs to be included in the impact severity index.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.12
• /
• pp.55-60
• /
• 2015

PG and RG methods are widely known method for calculating the capacity of the emergency generator in construction electrical installation. PG and RG methods are mainly used as a saving a life, fire protection, fire fighting in construction. Because no long distance between the emergency generator and electric motor feeder, the relatively small motor power in construction electrical installation, the capacity of generator in PG and RG methods are little problem of voltage and reactive power of generator. However in many cases the application of the PG and RG method is difficult in the Chemical Plant because it is long distance between the generator and the motor Feeder and motor capacity is very large. Motor starting power factor is about 0.2 lagging power factor and motor starting current is about 6times during motor staring. Also Most of the staring current component is a reactive power component. therefore, it is many cases that lack of reactive power and excess of allowable voltage drop limit and After selection of emergency diesel generator, problems happen during motor starting. Therefore, to be selection of effective emergency generator, active generator power, reactive power and the required reactive power during large motor starting should be considered in chemical plant. It is also required of the verification process through simulation because hand calculation is very difficult considering study cases.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.4
• /
• pp.522-530
• /
• 2018

This study proposes the mitigation method of shaft voltage by varying the parasitic capacitance. First, the shaft voltage explained. Second, the parasitic capacitances causing shaft voltage are analyzed respect to geometry of motor and windings. Then, the equivalent circuit is established to obtain the shaft voltage and output torque characteristic and develope appropriate motor structure. Finally, simulation and experiment are conducted to verify that modified motor suppress the shaft voltage. This novel model does not require additional hardware.

• Journal of Korean Society for Quality Management
• /
• v.21 no.2
• /
• pp.71-84
• /
• 1993

Currently the problem of air pollution caused by the motor vehicle emission is one of the most serious problems to be solved. Thus we needed the vehicle emissions audit procedure and technical innovation constraining the motor vehicle emission. The Korean Environmental Protection Agency currently audits automobiles for emissions compliance at assembly plants with multiple attribute multiple staged sampling plans. In order to establish the more reasonable audit procedure, the multiple staged sampling plan designed in this paper has been applied to the domestic vehicles by analyzing the statistic characteristics of the emission distribution. This paper summarizes the auditing procedure and develops methods for determining its statistical characteristics. Specifically, we consider how to evaluate a multiple staged sampling plan, give a procedure that efficiently estimates attribute-type probabilities from multivariate variables-type data, and quantify the effect of tightening the acceptable quality level of the sampling plan. As a result it can be proved that this audit procedure is the reasonable plan minimizing the AQL (Acceptable Quality Level) and is to be used effectively for the auditing procedure constraining the injurious gasses of the motor vehicles.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.40-47
• /
• 2003

A low-cost current-sensing scheme for the motor drives with MOSFET is described. Many motor drives usually employ the common current sensors to measure current for the purpose of control or protection. These current sensors, however, significantly burden the power circuit with the size and cost. The proposed current-sensing scheme utilizes information concerning MOSFET's On-voltage and On-resistance. An analogue circuit detecting On-voltage can overcome the above disadvantages because the circuit is small and is made at a low cost, and the fuzzy inference for On-resistance is also simply designed based on MOSFET's characteristics. The validity of this scheme will be experimentally verified by adopting the current control of a battery car.

• Proceedings of the KIEE Conference
• /
• 2000.11a
• /
• pp.76-78
• /
• 2000

The previous MCC's have the demerits of high cost and much manhour for rework because they are impossible for the standardization of products and have many manual connections. The customers require the products which can operate in connection with SCADA system by digitalizing the functions of the current MCC's and are systematized with capability of remote control. To solve these disadvantages and requirements, we developed the Electronic Motor Control System according to starting type for applying to fields based on this. This system has the various functions such as protection, measurement, and communication. Using these functions, it can monitor motor status through communication with the upper system and define the circuit for lower connection cost according to starting type and shorter manufacture period by program. The development of this product results in establishment of competitive structure with domestic competition and perfect automatic monitoring through linkage with SCADA system. In addition, it provides the comparable dominancy of receiving on orders in switch gear and adaptability to change of MCC market in Japan and Europe.