• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2009년도 정기총회 및 추계학술대회 논문집
• /
• pp.96-98
• /
• 2009

This paper propose a method to detect the rotor position of IPMSM(Interior permanent magnet synchronous motor) at standstill without a position sensor. The proposed method is based on current variation caused by the magnetic saturation of stator core as rotor position. By choosing an appropriate voltage vector and applying it to phase winding, it enables the algorithm to discern between a north pole and south pole, and subsequently estimates an absolute position. This method dose not depend on the model of the motor and the motor parameter.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2181-2186
• /
• 2014

Generally, the motor inside vehicle is exposed to highly ambient temperature and large vibration according to repeatedly starting and stopping for very short time. So, in this paper, the rotor shape design was performed to improve demagnetization endurance by considering the starting current of the Brushless DC (BLDC) Motor through the Finite Element Method(FEM). As a result, the partial irreversible demagnetization was occurred by starting current at the end of Permanent Magnets of the basic model. To solve this problem, the flux barrier design was performed and the flux on the rotor core was limited. Accordingly, demagnetization endurance and operating characteristics were improved.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.336-338
• /
• 2006

Diagnostic tests are used to evaluate the insulation condition of stator windings in traction motor. These tests included ac current, tan delta and maximum partial discharge. The insulation condition of stator windings was assessed by three test items. The stator windings of traction motor were m good condition. After completing the diagnostic tests, the stator windings of traction motors were subjected to gradually increasing ac voltage, until the insulation punctured. No.5 stator windings failed near rated voltage of 18.9 kV. The breakdown voltage of No.1 stator windings was 13.0. The failure was located m a line-end coil at the exit from the core slot.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 정기총회 및 추계학술대회 논문집 학회본부
• /
• pp.56-58
• /
• 1993

This report describes the high speed DC motor (8,000 rpm) that we have designed, manufactured and tested. DC motor is the best drive system in electric-mechanical energy conversion. The design concept for high speed and high energy density to DC motor is to maximize Ampere-conductor in armature and to maximize flux density in armature teeth, armature core, pole, yoke using flux path.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.518-525
• /
• 2005

The electromagnetic noise generates when natural frequencies of a stator core with wingdings and frame coincide with or approach natural frequencies of the magnetic motive force. In order to suppress such noise, the estimation of natural frequencies of the motor is important at the design stage. However, the natural frequency analysis is not so easy because motor stator is in the laminated plate structure and windings are composed of wires, insulation sheets and vanishs. Thus the accurate prediction of the equivalent material properties of windings becomes an essential task. In this paper, we derive the equivalent material properties using homogenization methods.

• 한국정밀공학회지
• /
• 제24권8호통권197호
• /
• pp.89-96
• /
• 2007

In this paper, a new air bearing stage with magnetic preload and a linear motor has been developed for the small precision machine systems. The new air bearing stage is unique in the sense that permanent magnets attached bottom of the iron core of table are used not only for preloading air bearings in vertical direction but also for generating thrust force by current of the coil at base. The characteristics of air bearings using porous pads were analyzed with numerical method, and the magnetic circuit model was derived for linear motor for calculating required preload force and thrust force. A prototype of single axis miniature stage with size of $120(W){\times}120(L){\times}50(H)\;mm^3$ was designed and fabricated and examined its performances, vertical stiffness, load capacity, thrust force and positioning resolution.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.24-26
• /
• 2004

The PM(Permanent Magnet) stepping Motor has been used widely to a variety of industries because of the open-loop control characteristic, a relatively large frequency range of velocity control and non-accumulated error of the step angle. Moreover, It has been gradually applied to office automation, machine intelligence, digital appliance, and automobile parts. This paper presents the optimal design results by use of the experimental method. The design variables of the PM stepping motor are shape of the claw-pole, material of core, and air-gap. As a result, a superior claw-pole PM stepping motor for OA machinery was developed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.978-983
• /
• 2009

This paper analyzed longitudinal end effect occurred in linear induction motor by using I-d direct solution and its result is verified by 2-d Finite Element Method(FEM). Longitudinal end effect of linear induction motor caused by magnetic discontinuity in primary core and electric discontinuity in armature winding has been investigated by many researchers. In this paper, 1-d direct solution and boundary conditions proposed by Yamamura and Nasar is used to analyze end effect of linear induction motor and its solution is verified by 2-d FEM.

• Journal of Magnetics
• /
• 제22권2호
• /
• pp.266-274
• /
• 2017

In this paper, torques of two motors are compared by Finite Element Analysis (FEA). One has a symmetric rotor structure and the other has an asymmetric rotor structure. The comparison shows that the asymmetric rotor structured motor has reduced torque ripple compared to the symmetric. The torque of the compared motor models was analyzed by separating into magnetic torque and reluctance torque. Through the analysis of torque component separated, it is shown that the magnetic torque and the reluctance torque compensate each other in the motor with the asymmetric structure rotor. Here "compensate" means decrementing the effect of one or more harmonics. It is shown how this compensation appears between the magnetic torque and the reluctance torque by looking into back electro motive force (emf) and the relative permeability distribution of rotor core.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권3호
• /
• pp.138-144
• /
• 2000

The detent force caused by the interaction of magnets with the teeth of a armature core deteriorates the driving performance of a permanent magnet linear synchronous motor. In this paper, we analyze the fields and forces of a linear synchronous motor with segmented or skewed magnet arrangement according to lateral overhang length of permanent magnets. For the analysis, the 3-dimensional equivalent magnetic circuit network method is used. The detent force and the static thrust are analyzed according to the segmented or skewed angle and the overhang length of permanent magnets, and the optimal angles that the detent force is minimized are found out in each case. The analysis results are compared with the experimental ones and shown a reasonable agreement.