• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.93-103
• /
• 2009

The concept of the effective moment of inertia has been generally used for the deflection estimation of reinforced concrete flexural members. The KCI design code adopted Branson's equation for simple calculation of deflection, in which a representative value of the effective moment of inertia is used for the whole length of a member. However, the code equation for the effective moment of inertia was formulated based on the results of beam tests subjected to uniformly distributed loads, which may not effectively account for those of members under different loading conditions. Therefore, this study aimed to verify the influences of moment shapes resulting from different loading patterns by experiments. Six beams were fabricated and tested in this study, where primary variables were concrete compressive strengths and loading distances from supports, and test results were compared to the code equation and other existing approaches. A method utilizing variational analysis for the deflection estimation has been also proposed, which accounts for the influences of moment shapes to the effective moment of inertia. The test results indicated that the effective moment of inertia was somewhat influenced by the moment shape, and that this influence of moment shape to the effective moment of inertia was not captured by the code equation. Compared to the code equation, the proposed method had smaller variation in the ratios of the test results to the estimated values of beam deflections. Therefore, the proposed method is considered to be a good approach to take into account the influence of moment shape for the estimation of beam deflection, however, the differences between test results and estimated deflections show that more researches are still required to improve its accuracy by modifying the shape function of deflection.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.231-239
• /
• 2004

A new scheme to estimate the moment of inertia in the motor drive system in very low speed is proposed in this paper. The simple estimation scheme, which is usually used in most servo system for low speed operation, is sensitive to the variation of the machine parameter, especially the moment of inertia. To estimate the motor inertia value, Reduced-Order Extended Luenberger Observer (ROELO) is applied. The effectiveness of the proposed inertia identification method using the RORLO is verified by simulation and experiment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1575-1582
• /
• 1992

This study describes the response performances of actual engine speed, turbocharger speed, air mass flow rate through engine, boost pressure ratio, exhaust temperature and combustion efficiency for a six-cylinder four-stroke turbocharged diesel engine during the change in operating conditions by using the computer simulation with test bed. In order to obtain the transient conditions, a suddenly large load was applied to the simulation engine with the several kinds of inertia moment in turbocharger and engine, and engine set speed. From the results of this study, the following conclusions were summarized The inferior response performances was mainly caused by turbocharger lag, and air mass flow rate and boost pressure ratio were closely related to the turbocharger speed. A reduced moment of turbocharger inertia resulted in less transient speed drop and much faster recovery to the steady state of the engine. The increase of moment of engine inertia reduced cyclic variation of engine speed. When a large load was applied to the engine at high speed, the engine could be fastly recovered. However, when the same load was applied to the engine at low speed, the engine was stalled.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.209-212
• /
• 2008

Corrugated steel-concrete composite deck with I-beam welded is lighter and has higher load carrying capacity than RC slabs due to an I-beam embedded in the corrugated deck. The methods suggested from ACI and design standard of roadway bridge are used to evaluate effective moment inertia of RC structures. This paper presents evaluation and application of effective moment inertia for corrugated steel-concrete composite deck with I-beam welded by using the methods suggested from design standard of roadway bridge, ACI and CEB-FIP MC-90. In order to evaluate effective moment inertia, a series of flexural experiments were carried out. Five beams were built and the parameters considered in the experiments were studs, shape of the sections and connections of the beams. By using the aforementioned methods, effective moments of inertia was calculated and they were compared with the experimental results. As a result, The method suggested from CEB-FIP MC-90 yielded more satisfactory agreement than that from ACI. It was found that the beam has studs showed high load-carrying capacity and high effective moment of inertia.

• Structural Engineering and Mechanics
• /
• v.10 no.3
• /
• pp.197-209
• /
• 2000

The effects of weight and axial inertia of a beam are taken into account for studying the nonlinear vibration of the Timoshenko beam due to external loads. The combination of Galerkins method and Runge-Kutta method are employed to obtain the dynamic responses of the beam. A concentrated force and a two-axle vehicle traversing on the beam are taken as two examples to investigate the response characteristics of the beam. Results show that the effect of axial inertia of the beam increases the fundamental period of the beam. Further, both the dynamic deflection and the dynamic moment of the beam obtained with including the effect of axial inertia of the beam are greater than those of the beam without including that effect of the beam.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.4
• /
• pp.1-6
• /
• 2012

The accurate information of mass properties is required for the precise control of the spacecraft. The mass properties, mass and inertia, are changeable by some reasons such as consumption of propellant, deployment of solar panel, sloshing, environmental effect, etc. The gyro-based attitude data including noise and bias reduces the control accuracy so it needs to be compensated for improvement. This paper introduces a real-time inertia estimation method for the attitude determination of STSAT-3, Korea Science Technology Satellite. In this method we first filter the gyro noise with the Extended Kalman Filter(EKF), and then estimate the moment of inertia by using the filtered data from the EKF based on the Recursive Least Square(RLS).

• Journal of the Korea Concrete Institute
• /
• v.28 no.6
• /
• pp.655-663
• /
• 2016

The present study shows the moment-average curvature relationship and effective inertia moment of RC beams obtained from the nonlinear analysis based on the parabola-rectangular stress-strain curve defined in EC-2 code. The variables examined are concrete strength and steel ratio, and moment-average curvature relationship and effective inertia moment obtained are compared with those of the current KCI provisions. As the results of the comparison, the followings could be said: Since the KCI provisions(the Branson method) were originally derived based on the experimental data ranged from 2.2 to 4 of $M/M_{cr}$ and 1.3 to 3.5 of $I_{ut}/I_{cr}$, thereby within these ranges the inertia moments obtained from the nonlinear analysis are closely agreed with those predicted by the Branson method. However, beyond those range the remarkable difference could be found between the two results. In particular, for beams having low steel ratio the inertia moment resulted from the nonlinear analysis are significantly smaller than those obtained from the KCI(Branson) method. This result may imply that the deflection of lightly reinforced members, such as slabs in buildings, becomes much larger than those calculated according to the current design provisions.

• Journal of Astronomy and Space Sciences
• /
• v.39 no.3
• /
• pp.99-108
• /
• 2022

There are two models that explain the rotation curves of galaxies: dark matter, which gives the missing contribution to the gravitational potential of the standard theory of gravity, and modified theories of gravity, according to which the gravitational potential is created by ordinary visible mass. Both models have some disadvantages. The article offers a new look at the problem of galactic rotation curves. The author suggests that the moment of inertia creates an additional gravitational potential along with the mass. The numerical simulation carried out on the example of fourteen galaxies confirms the validity of such an assumption. This approach makes it possible to explain the constancy of gas velocities outside the galactic disk without involving the hypothesis of the existence of dark matter. At the same time, the proposed approach lacks the disadvantages of modified theories of gravity, where the gravitational potential is created only by the mass of visible matter.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.14 no.4
• /
• pp.3-14
• /
• 1977

There are many Beam-Column connections in general structures and ship structures. For simplicity and convenience of analysis, the connections are mostly considered hinged when not reinforced or rigidly fixed when reinforced. This paper has intended to analyze the Beam-Column connection which is assumed two dimensional flat plate. The analysis has been preformed by Finite Element Method following the change of moment of inertia at connection. The conclusion of this investigation is as follows: By reinforcing or increasing the moment of inertia at connection part, the stress distribution of whole structure and the stress concentration at that part are relieved. Displacements of beam(when column is fixed) are almost linearly decreasing by the change of moment of inertia at connection.

• Structural Engineering and Mechanics
• /
• v.38 no.4
• /
• pp.459-477
• /
• 2011

Due to the low elastic modulus of FRP, concrete members reinforced with FRP rebars show greater deflections than members reinforced with steel rebars. Deflection is one of the important factors to consider the serviceability of horizontal members. In this study flexural test of AFRP reinforced concrete beams was performed considering reinforcement ratio and compressive strength as parameters. The test results indicated that flexural capacity and stiffness increase in proportion to the reinforcement ratio. The test results were compared with existing proposed equations for the effective moment of inertia including ACI 440. The most of the proposed equations were found to over-estimate the effective moment of inertia while the equation proposed by Bischoff and Scanlon (2007) most accurately predicted the values obtained through actual testing.