• 한국식품위생안전성학회지
• /
• 제11권3호
• /
• pp.221-225
• /
• 1996

For the purpose of improving hygienic quality of health-foods, sterilization effects of ${\gamma}$-ray and ozone on microoganisms associated with food cultured in the media and contaminated in Angelica keiskei powder were investigated. Ozone was immersed in water and sprayed in air, on the concentration of 3 mg liter-1 at an air flow rate of 5 liter min-3. Test strains cultured in the media completely inhibited by ${\gamma}$-ray at irradiation doses of 0.25~2 kGy. In the case of ozone, test bacteria inactivated after treatment of 10~20 minutes, but test mold, Aspergillus flavus was not effective. Strains contaminated in Angelica keiskei powder completely inhibited by ${\gamma}$-ray at irradiation doses of 2.5~7.5 kGy. However, when the powder was sprayed with ozonized air for 10hours, Bacillus subtilis and Staphylococcus aureus among five strains were eliminated.

• 소성∙가공
• /
• 제13권3호
• /
• pp.230-235
• /
• 2004

A new design based on the appropriate geometry of molded part and type of runner system under the optimal processing conditions was proposed to minimize the micro weld lines on the sub deco surface molded by two shot molding. Theoretical and experimental studies were conducted to examine the cause of the weld lines during the overmolding process in two shot molding. Various dimensions and geometries of substrate$(1^{st}shot)$ and the wall thickness of overmold$(2^{nd}shot)$ have been proposed to avoid the weld lines which are the most inevitable appearance defects occurred on the sub deco. The each design proposal was analyzed by mold flow analysis after part modeling. The analysis results were compared with molded part from mass production tool. It could be seen that from the analysis that the proper geometry of plastic part and type of runner system considering pressure drop under the optimal processing conditions were the most influential factors to avoid weld lines occured on the sub deco.

• Computers and Concrete
• /
• 제16권1호
• /
• pp.179-190
• /
• 2015

An experimental program has been carried out to investigate the effect of edge-slope on compressive strength of concrete specimens. In this study, effect of such slope was investigated by testing 100 standard cylinder specimens and 40 standard cubes. When molds are put on a slanted place, wet concrete starts to flow through the open end of mold. It keeps flowing until it reaches to a parallel surface with the place over which it was placed. That creates a sloped surface over the loading area. Experimental results revealed significant relationships between failure loads and slope of loading surface for cylinders. Angled cracks occurred in sloped cylinder specimens. Tension cracks occurred in cube specimens. Fracture mechanisms were also evaluated by using finite element analyses approach. Experiments yielded an exponential curve with bandwidth for cylinders. Average value of curve is $y={\frac{\pi}{2}}e^{-cf}$ between slope and compressive strength. Inclination is much effective parameter for cylinders than cubes.

• 한국농공학회논문집
• /
• 제47권4호
• /
• pp.35-41
• /
• 2005

In order to analyse the flow problems for an unsaturated soil, it is required to examine closely the characteristics of the coefficient of permeability which is changing with the matric suction. To this ends, a permeability test was conducted on the three samples;granular soil, cohesive soil and silty soil. The specimen was made by pressing the static pressure on the mold filled with soil and the void ratio was controled with the different compaction ratio. And the test was performed by using the modified apparatus of the steady state method which was proposed by flute (1972). The range of matric suction was 0-90 kPa. The measured results for the coefficients of permeability were analysed with the void ratio and the compaction ratio, and it was examined closely the characteristics of the permeability for an unsaturated soil.

• 한국산학기술학회논문지
• /
• 제12권1호
• /
• pp.55-61
• /
• 2011

축전지 용기는 폴리프로필렌으로 사출되며, 결정성 고분자 수지로 변형이 많이 일어나는 특성이 있다. 따라서 본 연구에서는 축전지 용기의 사출시 사용되는 Gate를 개선하여 금형의 공정을 단순화시킴으로써 생산비용의 절감과 성형품의 품질개선에 중점을 두고 CAE 해석을 실시하였다. 그 결과 성형과 제품에서 발생될 수 있는 유동의 불균형과 변형 등을 예측하여 제품의 불량률 감소로 신뢰성 향상에 기여할 것이다.

• 한국주조공학회지
• /
• 제9권1호
• /
• pp.39-48
• /
• 1989

A basic three dimensional thermal model has been developed to simulate the solidification sequence for gravity die casting process. The finite difference method was used to analyze the solidification process during all the casting cycles. The prediction of die temperature in the quasi-steady state was analyzed by the boundary element method. The influence of die cooling on the heat flow in the cast/mold system was also investigated. Predictions of the computer simulation on temperature profiles and location of shrinkage defects were in good agreement with those observed in experimental die castings. Models of computer simulation which is developed by this work can be useful for the design and process control of die casting.

• 소성∙가공
• /
• 제15권1호
• /
• pp.76-81
• /
• 2006

In this study, warpage characteristics of mobile phone cover through injection molding process were investigated using design of experiments in injection molding process. Warpage in plastic injection molding has a significant effect on quality of product. Effects of injection time, packing pressure, packing time, mold temperature and melt temperature on the warpage of mobile phone cover were considered by numerical analysis and experiment with Taguchi method. The degree of warpage for the injection molded part was measured by using three dimensional coordinate measurement machine. It was shown that temperature control factor has more significant effect on the warpage of mobile phone cover than pressure control factor.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.143-146
• /
• 2003

In this paper, a new preform design method is proposed to eliminate the excessive flash in metal forging process. After carrying out finite element simulation of the process with an initial billet, backward particle tracing is performed from the outlet of the flash. Then, the region which belongs to the flash is easily found .. The process is analyzed again with the redesigned billet which is removed that region the above mentioned region. The optimal preform shape which minimizes the amount of flash without changing the forgibility can be obtained in several iterations.

• 연구논문집
• /
• 통권29호
• /
• pp.173-183
• /
• 1999

The vacuum investment casting process for a large gas turbine component, Inner Preswirl Support (IPS), was simulated by using commercial FEM package ProCAST(TM) with view factor radiation method. The solid fraction in mushy zone was directly measured by Differential thermal analysis(DTA-DSC mode). Three types gating design. considering liquid flow and heat release through it. were proposed. Solidification had begun at the ribs or thin sections of the IPS casting and advanced further through the upper and lower gates. The computed temperature gradient G and G/R values at 70% solidified temperature were used for prediction of microshrinkage formation during casting. The effect of mold preheat on the thermal history of the casting displayed minute effect on the microshrinkage formation.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.280-283
• /
• 2002

In the manufacturing of large scale composite structures, the cost-effective processing and the enhancement of structural performance are critical. One of the most effective ways for this purpose is to use stitched multiaxial warp knitted (MWK) perform in the resin transfer molding process. This study reports the effect of stitching on the mechanical properties of MWK composites, and the feasibility processing of the thick U-beam structure utilizing the stitched preforms. Permeability of the preform, viscosity and cure property of the epoxy resin have been measured. The results of resin flow analysis has been used in determining the gate/vent locations of the RTM mold. Cross-sectional observation of the channel beam prototype demonstrated that the resin impregnation was almost complete, except for some surrounding area of stitched yarns.