• Journal of the Korean Society of Industry Convergence
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2018

The purpose of this study is to develop a high-strength, high-toughness, thin-walled aluminum shock absorber housing product by applying a high vacuum die casting method to improve internal gas defect and formability. The analysis program dedicated for the casting was used because it was too costly and time-consuming to adopt the gating system design. The final casting plan was designed based on the flow pattern of the material filled into the mold and the result of air pressure and air pocket after the material was completely filled in the mold. Gaty shape was designed as a split type. The runner was designed to have the same shape as the initial inlet curve of the cavity, and the flow of the molten metal was prevented from turbulent flow. The most favorable results were obtained when the injection speed was $V_2=4.0m/s$. Defects on pores were reduced by applying high vacuum level inside the mold.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.79-83
• /
• 2012

Anti-theft safety caps for bolted joints are necessary to ensure the safety of citizens and prevent theft of manholes, bridge guardrails, bulletin boards, subway safety handrails and others. Safety caps enhance the look of bolted joints, avert accidents that involve hitting the head of bolts, hamper them from coming loose by covering the head of bolts. This study focuses on press die design methods and press molding condition setting to resolve bursting and cracks in products, and on molding material selection and heat treatment technologies to boost life extension.

• Design & Manufacturing
• /
• v.2 no.4
• /
• pp.24-31
• /
• 2008

The productive products are required diversification of product development and advanced for competitiveness. A lot of methods to fix architecture wrapping panels and stone materials are developed in domestic area very much. In this paper, it is very important that a fixing device of slate and molds were developed to reduce the production cost and improve safety. Therefore new model was suggested to reduce manufacturing cost and structure design and FEM analysis were performed to manufacture die press dies for mass production.

• Design & Manufacturing
• /
• v.9 no.3
• /
• pp.24-28
• /
• 2015

Speaking in general terms the form injection process can be described as a new process-variant of already known structural foam molding technology which roots go back to the early sixties. The most limiting factors of already know foaming processes are large cell size and the lack of uniformity of these cells as well and the inability to foam all kinds of plastic materials. In this paper, Process Study on weight change in injection rate during foaming. Experimental conditions were set as the injection speed 50,150,300 and 450 mm/s. The experiments PA, PA+GF, PP, was confirmed that the weight increase to PP+TA.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.12-16
• /
• 2012

In this study, an injection mold is made to produce polymer line post insulators. FRP (fiber reinforced plastics) is covered by silicone housing. In injection molding process, chances for offcenter are 60 percent. Given the structure of the product, offcenter occurs owing to the imbalances in positions of gates and improper -designs of cores and jigs. This study focuses on mold modifications and improvements.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.23-26
• /
• 2008

In order to examine the deformation characteristics of Al circular pipe underthe biaxial compression, the horizontal biaxial compression die for the experiment was manufactured. From this, in the various compressive strain rate (1 mm/min. ${\sim}$ 400 mm/min.)conditions, the circular pipes, which were made by Al materials, were investigated based on the properties change of cross section area, punch load and deformation behavior. The tensile and compressive strains were evaluated from micro Vickers hardness tester. From these results, the punch load and deformation characteristic of Al circular pipes were highly changed in the compressive strain rate about 200 mm/min. The Al circular pipes had the tendency that the punch load decreased with increasing the compressive strain rate. In addition, following as the change of the shape and position of neutral axis due to the deformation proceeding of the circular pipe, the special point of the internal circular pipe at maximum load showed the maximum deformation strain and the maximum measured hardness value. The CAE (computer aided engineering) simulation using Deform-2D program was performed on the circular pipe in order to know and verify the exact compressive deformation behavior. From these results, the experimentally measured results were reasonably in good agreement with the simulation results.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.90-95
• /
• 2012

The sheet metal forming proceccing is very important and indispensable in the automotive industry because the accuracy of prsee worked parts is directly related to the automotive quality. But when making mold it is difficult and expensive to modify mold. mold design technology is a critical technology in press plastic working. When design the mold there are lots of variables in press plastic working according to worked material, mold materials, conditions of heat treatment, clearance and so on. Abrasion of mold depends on these kind of conditions and sheared surface which is crucial for quality of product also depends on them. In this study, we conduct research on abrasion loss of mold according to 8, 10 and 12% of clearance for thickness of 1.0mm of worked material out of mold design variables of the products whose worked materials are high carbon steel and carbon tool steel by a practical experiment and perform a comparative evaluation of difference of abrasion loss mold with the alloy tool steel (STD11) and Tungsten Carbide (WC).

• Design & Manufacturing
• /
• v.8 no.2
• /
• pp.12-17
• /
• 2014

Currently, injection molding process is a very useful technique that be applied to many field. And injection molding technology has been commercial based on many studies. However, there is no standard of surface roughness because there are few studies about surface technology of injection product. In addition, when designing the mold, changes of the core surface and the injection conditions are not considered. In this paper, change of surface according to the core and the injection conditions was compared with the surface of the injection product. Accumulation of these technologies will propose direction in mold design, manufacturing and injection molding technology.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.1-9
• /
• 2019

In-mold Coating is a method that can simultaneously perform injection molding and surface coating in injection mold. The material used for coating is two-component polyurethane which is composed of polyol and isocyanate. L-type mixing head can be used to mix polyol and isocyanate uniformly, and inject them inside the mold cavity. The surface quality of the injection molded products by using in-mold coating depends on the mixing uniformity between main agent and hardener. In this study, flow analysis was performed to design a mixing head for uniform mixing of two-component polyurethane. Especially the effects of design parameters of mixing head on mixing uniformity and nozzle pressure were investigated. The parameters of mixing head were mixing chamber diameter, cleaning cylinder diameter, nozzle alignment angle in the horizontal and vertical direction, and cleaning piston position. It was found that optimal design values were mixing chamber diameter of 3.5 mm, cleaning cylinder diameter of 5.0 mm, nozzle horizontal/vertical alignment angles of 140°/160°, and cleaning piston position of 1.8 mm. The optimal values would be used to develop a two-component mixing head achieving an uniform mixing for in-mold coating.

• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.51-57
• /
• 2016

The customized production market tends to get bigger due to the improvement of 3-D printing technology and a rise in national income. This research is to overcome the limitation of original production method which is localized under the mass production, and furthermore It is to find the intersection between the future 3D printer and a standard molding technology by manufacturing custom earphone with a low price.