• Journal of Korea Foundry Society
• /
• v.15 no.2
• /
• pp.184-193
• /
• 1995

Effects of process parameters during thixocasting, such as solid volume fraction, mold temperature and extrusion ratio, on the mold filling behaviour and fluidity of Mg alloy(AZ91D) have been investigated. The semi-solid ingot held for 60 minutes at the semi-solid temperature range did not contain the equilibrium volume fraction of solid as expected from the phase diagram. Therefore, in order to obtain the desired solid fractions, and to suppress the exaggerated grain growth during heating, it was required to heat the ingot rapidly up to the temperature $10^{\circ}C$ higher than the semi-solid temperature suggested from the phase diagram for a specific volume fraction of solid. The experimental results show that mold filling behaviour and fluidity can be improved with the use of the higher mold temperature and the lower volume fraction of solid, but remain nearly unaffected by the change of extrusion ratio.

• Design & Manufacturing
• /
• v.15 no.3
• /
• pp.7-12
• /
• 2021

Plastic injection molds used for rapid heating and cooling must minimize surface damage due to friction and maintain excellent thermal and low electrical conductivity. Accordingly, various surface treatments are being applied. The properties of Al₂O₃ coating and DLC coating were compared to find the optimal surface treatment method. Al₂O₃ coating was deposited by thermal spray method. DLC films were deposited by sputtering process in room temperature and high temperature PECVD (Plasma enhanced chemical vapor deposition) process in 723 K temperature. For the evaluation of physical properties, the electrical and thermal conductivity including surface hardness, adhesion and wear resistance were analyzed. The electrical resistance of the all coated samples was showed insulation properties of 24 MΩ/sq or more. Especially, the friction coefficient of high temp. DLC coating was the lowest at 0.134.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.3
• /
• pp.218-222
• /
• 2004

We developed the stamper structured mold with moving core type with nano pattern. Among the factors affecting the quality of injection molding plastic parts, We studied the effects of moving core surface heating method on the transcription of injection molding plastic parts with nano structures. Moving core surface heating has been tested by three different methods. The first was conventional injection molding process without heating moving core surface, the second was halogen lamp radiation heating process and the last was MmSH process using gas flame. As a result of making injection molded parts by using thermoplastic amorphous resins such as COC, PMMA, MmSH method which is the most high temperature of moving core surface showed the best nano pattern transcription of the three methods, but the outcome of conventional injection molding process was not better than others.

• Journal of Biosystems Engineering
• /
• v.8 no.2
• /
• pp.39-48
• /
• 1983

This study was performed to obtain the basic data which could be used for the modification of the manual center-burner-type rice-husk furnace into a small scale automatic type for the multi-purpose use in the farm. For this purpose, first, the utilization feasibility of the rice-husk furnace in the farm was analyzed briefly in aspects of available amount of rice-husk for the fuel, annual operation time and replaceble amount of residential heating energy with rice-husk in the farm. For the experiment a prototype furnace geared with an automatic feeding device was fabricated, and feed rate, mold size and chimney height were changed to investigate the combustion efficiency of rice-husk and thermal efficiency of the furnace. Also, optimum and limiting operational factors were observed in each treatments. The results obtained are summarized as follows. 1. If the rice-husk is intensively used for residential heating in the farm for winter season, on an average 51 percent of the total heating energy can be replaced with the rice-husk. Therefore, development of a small scale automatic rice-husk furnace was recognized to be feasible. 2. The operational condition depending on husk-feed rates was very important factor for successive steady burning operation of the given furnace. When the feed-rate was 1.5 kg/hr, the top of the burning zone should be kept at the position about 55 cm from the bottom of the combustion chamber with the periodic removal of ash (termed as steady state position), which was 18 cm above the mold waist. When the feed rates were 2.4 kg/hr and 3.0 kg/hr, the steady state position was at about 4 cm above the mold waist. 3. The mold size affected inflow rate of air into the furnace and consequently CO content in the exhaust gas. The relatively bigger mold gave positive effect on the air-inflow rate. 4. When the husk-feed rates were 1.5 kg/hr, 2.4 kg/hr, 3.0 kg/hr, the combustion efficiencies of the rice-husk were 98.5%, 97.4% and 95.0%, the thermal efficiencies of the furnace were 93.4%, 93.2% and 87.6%, and CO content in the exhaust gas were 1.21%, 1.03%, and 2.43%, respectively. The air-inflow rates were decreased with the increase of feed rates. When the amount of excess air was 30-40%, the CO content in the exhaust gas was at the minimum level. 5. When the chimney height was lowered from 260 cm to 96 cm, the air-inflow rate was slightly decreased, but the average temperature in the combustion chamber, CO content in the exhaust gas and combustion and thermal efficiencies were not changed significantly. 6. The incidental problems associated with the protytype furnace were accumulation of the ash inside the mold, accumulation of the cinder between the outer-drum of the furnace and the combustion chamber wall, and accumulation of the cinder in the chimney.

• Journal of Welding and Joining
• /
• v.12 no.3
• /
• pp.101-108
• /
• 1994

The horizontal continuous casting process with the heating mold was adopted for fabricating defect-free 4043 Al alloy rods of 3.2m dia. with mirror surfaces. These rods were drawn into 2.4mm dia. rods for GTAW welding. The GTAW welding tests were carried out by use of these welding rods with 6061 Al alloy as a base metal. After welding, the X-ray tests, tensile strength tests, bending tests, and microstructural analysis of welded zone and HAZ were carried out. The results represented that the welding rods with good surfaces and welding properties could be made by the horizontal continuous casting, and followed by the drawing process.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.2
• /
• pp.93-96
• /
• 2012

We have designed high performance prism light-guide plate (LGP) in 17 inch TFT-LCD. In test result to embody high brightness BLU in case of LGP of base and upper surface with 17 inch, thickness 8mm adding prism construct. Using optical simulation, we forecast the brightness and uniformity in LGP with prism structure. And we adopted novel injection mold method and Nickel stamper to make actual evolution sample. Novel injection mold process has steady heating time zone in heat cycle time of injection mold process. For this novel heat cycle control, we achieved above 90[%] height prism structure as our design. It is superior brightness improvement than previous that of printing form about some 20[%] and in this course to embody actual material it succeeded prism LGP production by 17 inch injection form process.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.3
• /
• pp.110-118
• /
• 1995

The filling phase analysis of the injection molding process for thermoplastics was applied to predict pressure, themperature and shear stress in the test mold, and the results were compared with the experiment using 30% glass fiber added ABS resin. The finite difference method was used in the analysis considering the effects of heat transfer between molten polymer and mold wall, and also frictional heating by shear flow. The analysis results were considered as a method to improve the quality and the productivity of injection molding process. Using the analysis results, the molding factors such as mold-ability of polymers, performance of injection molding machine, positioning of gate and dimendsioning of runner in the injection molding process can be estimated at the design stage of mold for good quality and productivity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.09a
• /
• pp.9-12
• /
• 2005

The rapid thermal response (RTR) molding is a novel process developed to raise the temperature of mold surface rapidly to the polymer melt temperature prior to the injection stage and then cool rapidly to the ejection temperature. The resulting filling process is achieved inside a hot mold cavity by prohibiting formation of frozen layer so as to enable thin wall injection molding without filing difficulty. The present work covers flow simulation of thin wall injection molding using the RTR molding process. In order to take into account the effects of thermal boundary conditions of the RTR mold, coupled analysis with transient heat transfer simulation is suggested and compared with conventional isothermal analysis. The proposed coupled simulation approach based on solid elements provides reliable thin wall flow estimation fur both the conventional molding and the RTR molding processes

• Journal of Korea Foundry Society
• /
• v.14 no.6
• /
• pp.499-507
• /
• 1994

The effect of sodium gluconic acid on the collapsability of the sodium silicate type $CO_2$ mold was studied. The bending strength was saturated with gassing $CO_2$ for 60 sec. under $1kg/cm^2$ and with the flow rate of $10\;{\ell}\;/min$. It was decreased with aging after having been fully hardened. The retained strength was reduced in the heating temperature range of $100{\sim}1,100^{\circ}C$ and the retained strength peak near the heating temperature of $100^{\circ}C$ was removed by the effect of the sodium gluconic acid. Silica gel, $Na_2CO_3$ and dehydrated sodium silicates were formed from the binder of sodium silicate with the addition of sodium gluconic acid at the heating temperature of $100^{\circ}C$. $Na_4SiO_4$ was formed by the reaction of $Na_2O$, from decomposed $Na_2CO_3$, with the dehydrated sodium silicate at $500^{\circ}C$. The crystobalite type of $SiO_2$ was formed at $900^{\circ}C$. The sodium gluconic acid had no effect on the bending strength at around $1,100^{\circ}C$ due to the combustion loss of it.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.567-568
• /
• 2006

Generally, progressive type GMP process is more efficient than batch type because there are advantages that problems of each stage(heating, press, cooling etc.) are easily grasped and a time of production is shortened. But if single cavity is used in progressive type GMP process, there is disadvantage that productivity is decreased. So, in order to improve productivity of progressive type GMP process, it is essential to secure multi cavity mold technic. In this study, as a fundamental study to develop multi cavity used in glass lens molding, we conducted a compression test for PBK40.