• 한국주조공학회지
• /
• 제11권1호
• /
• pp.44-53
• /
• 1991

The proper feeding conditions for thin Al-Alloy (AA336, JIS AC8A) castings in permanent mold were investigated to eliminate microshrinkage porosity. 5mm-thick plates (200mm long, 60mm wide) were cast with increasing padding taper from 0 to 5% under different conditions : (1) constant mold temperature of $350^{\circ}C$, (2) continuous production with uniform mold thickness (10mm), (3) continuous production with a negative taper of 2.5% in mold thickness (thickness decreasing in direction to riser). The test casting were machined off to the midplane and the shrinkage porosity was examined visually. The critical padding taper which can just eliminate the shrinkage porosity was determined for each condition, i.e. : (1) 4.5% at the constant mold temperature, (2) 3.5% for continuous production with the uniform mold thickness (3) 1.5% for continuous production with the taper in mold thickness. A computer simulation by a finite difference analysis program was applied to the test casting. The liquid fraction gradient (LFG) and the temperature gradient divided by the square root of the cooling rate (G /SR) were calculated at the end of solidification and compared with the shrinkage porosity area in the castings. For the case of constant mold temperature, LFG is a better parameter to predict shrinkage porosity than G /SR and its critical value is around 11%/cm. But for the case of continuous production, neither LFG nor G /SR could be a reliable parameter. The experimental results about the critical padding taper are of practical interest for designing permanent molds and castings. The computer simulation results stimulate further research to be directed on the prediction of centerline microshrinkage porosity in continuous production.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.30-33
• /
• 2016

It is true that the plastic shrinkage is inevitable. Shrinkage rate in effect at the time of mold design will soon determine the size of the global product. Process for the shrinkage of the plastic that provides how made, yet it has identified a process for making the question whether the shrinkage that can be trusted, and by the experimental results were as follows: as shrinkage, see ISO but, according to circumstances the process can go to the agreement between the parties. shrinkage ratio of the pressure sensor installed in the specimen mold is essential, amount of pressure sensor is that it is appropriate approximately 2-3. proper holding pressure is a significant effect on shrinkage Mitch, so that the effect of selecting the contraction ratio data according to the appropriate holding pressure during mold making. shrinkage CAE analysis results are difficult to utilize in the mold-making chamber. Based on these results, it concluded by looking forward to the improved products produced shrinkage.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1939-1943
• /
• 2008

Deformation of a mold is measured and analyzed in alignment and curing processes of UV-Imprint Lithography. We are focused on mold deformation caused by a UV resin, which is laminated between a mold and a target glass-panel. The UV resin is viscous in case of liquid state, and the resin will be solidified when being exposed by the ultra-violet light. The viscosity of the resin causes shear force on the mold during the alignment process. Moreover, the shrinkage during phase change from liquid to solid may cause residual stress on the mold. The experiments for measuring temperature and strain are made during alignment and curing process. Strain-gages and thermocouples are used for measuring the strain and variation of temperature on several points of the mold, respectively. The deformation of mold is also simulated and analyzed. The simulation results are compared with the experiments. Finally, sources of alignment errors in large area UV-nanoimprint lithography are discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.132-137
• /
• 2002

The mold transformers have been widely used in underground substations in large building and have some advantages in comparison to oil-transformer, that is low fire risk, excellent environmental compatibility, compact size and high reliability. In addition, the application of mold transformer for outdoor is possible due to development of epoxy resin. The mold transformer generally has cooling duct between low voltage coil and high voltage coil. A mold transformer made by one body molding method has been developed for small size and low loss. The life of transformer is significantly dependent on the thermal behavior in windings. To analyse winding temperature rise, many transformer designer have calculated temperature distribution and hot spot point by finite element method(FEM). Recently, numerical analyses of transformer are studied for optimum design, that is electric field analysis, magnetic field, potential vibration, thermal distribution and thermal stress. In this paper, the temperature distribution of 50 kVA pole mold transformer for power distribution are investigated by FEM program and the temperature rise test of designed mold transformer carried out and test result is analyzed compare to simulation data. In this result, the designed mold transformer is satisfied to limit value of temperature and the other property is good such as voltage ratio, winding resistance, no-load loss, load loss, impedance voltage and percent regulation.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.163-166
• /
• 2008

Injection molding operation consists of filling, packing, and cooling phase. The highest pressure is involved during the packing phase among the operation phases. Cavity pressure depends upon velocity to pressure switchover time and magnitude of packing pressure. The cavity pressure is directly related to stress concentration in the cavity of mold. Thus the observation and control of cavity pressure is very important to prevent mold cracking. In this study, cavity pressures were observed for operational conditions using the commercial CAE software,Moldflow. Operational conditions were velocity to pressure switchover time and packing pressure. Cavity pressures were also measured directly during injection molding. Simulation and experimental results showed good agreement.

• Design & Manufacturing
• /
• 제15권3호
• /
• pp.45-49
• /
• 2021

In this study, during the injection molding process, a device was manufactured and evaluated that calculates a cooling time by measuring a vibration signal generated from a mold using an acceleration. The last two parts, one of which has a large magnitude change in the measured vibration signal of a mold, were divided into a cooling start section (paking end section) and a mold opening section, and the time difference at the relevant points was calculated as the cooling time. The cooling time was monitored on a 5-inch light guide plate mold by applying the method. The manufactured device was attached to a fixed base of mold to measure the cooling time, and data was obtained remotely using Bluetooth technology. Then, the measured cooling time was compared with the cooling time set in the injection molding machine to evaluate the accuracy. As a result of the experiment, the cooling times measured by the devices were 15.675±0.024 sec, 20.637±0.014 sec and 25.623±0.079 sec of each conditions. Also, the measurement results were shown with errors of 0.655±0.044 sec, 0.637±0.014 sec, and 0.662±0.013 sec, respectively.

• 한국산학기술학회논문지
• /
• 제9권6호
• /
• pp.1754-1759
• /
• 2008

일반사출성형에서는 수지가 캐비티 내를 흐르면서 냉각으로 인한 점도의 상승으로 전사성이 급격히 나빠지기 때문에 미세패턴을 가진 성형품을 제작하는데 많은 어려움이 따른다. 이를 해결하는 방법으로 금형온도를 용융된 수지온도 수준까지 순간적으로 표면만을 가열하여 성형시킨 후 급속히 냉각하는 다양한 순간금형가열방식이 있고, 그 중 본 연구에서는 전열가열방식인 E-Mold을 채택하였다. 특히, 마이크/나노 부품 성형에 필수적인 E-Mold 금형설계에 있어 heating line의 배치는 금형의 온도 제어 및 균일한 온도 분포에 절대적인 영향을 미치므로 최적화된 heating line의 배치가 필수적이다. 본 연구에서는 사출공정의 사이클 타임을 최소화하면서 다양한 해석 프로그램을 사용하여 E-Mold의 최적화 설계를 전산모사 하였고, 이를 실험결과와 비교하였다. 먼저, 3D CAD 프로그램인 Pro-Engineer Wildfire 2.0 을 사용하여 E-Mold 금형을 설계하고, ANSYS사의 ICEMCFD 프로그램을 사용하여 MESH 생성하고, ANSYS사의 FLUENT 프로그램을 사용하여 금형의 초기온도 $60^{\circ}C$에서 $120^{\circ}C$와 $180^{\circ}C$까지 가열하는데 걸리는 시간과 냉각시키는데 걸리는 시간 등을 전산모사 하였다. 그리고 Polycarbonate를 이용하여 LGP 도광판을 실제 사출성형하여 얻은 데이터와 비교 분석을 하였다. 전산모사와 실제 사출결과에서 $3{\sim}4$초가량의 차이가 나타났지만 실제 사출시 고온의 용융된 플라스틱 수지에 따른 냉각시간의 오차를 생각한다면, 전산모사와 실힘결과는 거의 일치한다고 볼 수 있다. 따라서 본 체계적인 전산모사방법을 통해 E-Mold의 Heating Line 최적화 설계가 가능하다는 것을 확인하였다.

• 한국환경보건학회지
• /
• 제46권4호
• /
• pp.359-367
• /
• 2020

Objectives: Exposure to mold is strongly associated with adverse health effects (development or exacerbation of allergic diseases). We reviewed the health effects of mold exposure and explored to determine the annual distribution of indoor mold in facilities with susceptible populations. Methods: The health effects of mold exposure were mainly summarized by reviewing related papers and WHO research reports. We selected 10 facilities, including daycare centers, postpartum care centers, medical institutions, and elderly care facilities within the Seoul Metropolitan. Mold sampling was performed once every week or once every quarter from February 2016 to 2017. In addition, fungal species analyses was performed, and distribution status by month and facility was analyzed in the same manner as concentration. Results: Adverse health effects attributed to fungal exposure are largely divided into allergic symptoms, toxic effects, and infectious effects. Monthly mean concentrations of mold indoors and outdoors was 368.8 CFU/㎥ (geometric mean 213.4 CFU/㎥) and 496.0 CFU/㎥ (327.9 CFU/㎥), respectively. The indoor concentration has begun to increase in February, peaked in July, declined in August, increased again until October, and then decreased in November. About 36 genera of indoor fungal species were found in each facility. Cladosporium sp., Penicillium sp., Fusarium sp., Aspergillus sp., Alternaria sp., and Arthrinium sp. were observed as the dominant species. Conclusions: Our findings showed that the overall level of indoor mold was below the 500 CFU/㎥ level recommended by the Ministry of Environment. The development of DNA-based assessment and expanding facilities to be monitored for mold would be necessary for preventive aspects.

• 펄프종이기술
• /
• 제47권1호
• /
• pp.75-83
• /
• 2015

The applicability of oil palm biomass, EFB(Empty Fruit Bunch) as raw materials for environmental friendly packaging material, pulp mold, was evaluated in this study. The changes in the water absorption properties of pulp mold by the addition of EFB and the surface treatments with PVA and AKD were analyzed by measuring the changes in the water absorption rate and the water contact angle. The each pulp mold sample was prepared by using laboratory wet pulp molder. And the water absorption rate of each samples were evaluated by measuring times for the absorption of a 0.1 ml water drop on the pulp mold sample surface. The addition of EFB to the pulp mold made of OCC resulted in the decrease of water absorption rate and the increase in the water contact angle. The surface treatments with PVA and AKD on the OCC pulp mold showed the significant reduction in the water absorption rate. However, in case of ONP pulp mold, the addition of EFB and the surface treatments with PVA and AKD showed no big changes in water absorption times. Those might be come from the finer surface structure of ONP pulp mold which were made of more finer and flexible fibers and more hydrophilic fibers. The results of this study showed the functional properties such as water absorption rate, could be controlled by the application of EFB and the treatments with AKD or PVA, especially in case of the OCC pulp mold.

• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.70-78
• /
• 1997

3Y TZP/SUS316계 경사기능재료를 슬립캐스팅법을 이용하여 제조하였다. 슬립캐스팅 공정에서 석고몰드를 대체하기 위해 알루미나몰드를 제조하였고, 3Y-TZP/SUS316 2상 슬러리의 최적 분산조건을 ESA, 점도계, 침전거동의 관찰 등을 통해 결정하였으며, 석고몰드와 알루미나몰드로 캐스팅한 시험편의 제반 특성을 소결수축율변화, 건조 및 소결거동, 미세구조 관찰 등으로 조사하였다. 그 결과 알루미나몰드를 사용하여 제조된 시험편에서는 석고몰드 사용시 나타나는 표면에서의 오염이 관찰되지 않았으며, 각 층의 두께조절이 쉬웠고 높은 재현성을 나타냄을 알 수 있었다. 특히 알루미나몰드를 사용하여 제조한 SUS316에서는 어떤 열화현상도 관찰되지 않았다. 결국 슬립캐스팅 공정으로 3Y-TZP/SUS316계 경사기능재료를 제조함에 있어서 기존의 석고몰드보다 다공질 알루미나몰드의 사용이 바람직하다는 것을 알 수 있었다.