• Food Engineering Progress
• /
• v.15 no.2
• /
• pp.148-154
• /
• 2011

The objective of this study was to determine the effect of die geometry on expansion index of extruded corn flour. Water solubility index, water absorption index and specific mechanical energy (SME) input were analyzed to observe the relationship with die geometry. The feed moisture content was 20 and 25%. Die dimensions were tapered angle (57, 95o) and length/diameter (L/D) ratio of die land (0.67, 1.67 and 2.67). The SME input was the highest at 20% moisture content and 2.23E-10 m3 die constant. The sectional and volumetric expansion indices at 20% moisture were increased with increase in die constant. However, die constant did not influence sectional expansion index of corn flour extrudate at 25% moisture content. The extruded corn flour at 25% moisture content had higher longitudinal expansion index than those of extruded corn flour at 20% moisture content. Sectional expansion and longitudinal expansion index were negatively correlated. The water absorption index and water solubility index were not affected with the die constant.

• Food Engineering Progress
• /
• v.15 no.3
• /
• pp.262-268
• /
• 2011

The effects of pellet moisture content on physical properties (expansion ratio, density and breaking strength) of vacuum-puffed Yukwa (non-oil puffed Yukwa) were investigated in this study. The Yukwa was made from the waxy rice steeped at 25 and $30^{\circ}C$ for 3, 5 and 10 days with pellet drying times (6, 8 and 10.5 hr). As the drying time increased from 6 to 10.5 hr at $50^{\circ}C$, the highest value of pellet moisture content (29.4%) was found in the samples made from the steeped waxy rice at $25^{\circ}C$ for 5 days after 6 hr drying, while the lowest value (16.3%) was found at $25^{\circ}C$ for 3 days after 10.5 hr drying. Both redness and yellowness values of vacuum-puffed Yukwa increased as the drying time increased. The expansion ratio of Yukwa was greatly affected by drying time, ranging from 2.07 (26.8% pellet moisture content) to 7.01 (24.0% pellet moisture content). From the data, it can be concluded that the pellet moisture content had a significant influence on the physical characteristics of vacuum-puffed Yukwa. With vacuum puffing condition of 3 min heating and 2 min puffing, the pellets with about 25% moisture content showed higher expansion ratio, and lower density and breaking strength.

• Preventive Nutrition and Food Science
• /
• v.17 no.3
• /
• pp.203-209
• /
• 2012

The effects of variable moisture content, screw speed and barrel temperature on the physicochemical properties of red ginseng powder extrudates were investigated. The raw red ginseng powders were processed in a co-rotating intermeshing twin-screw extruder. Primary extrusion variables were feed moisture content (20 and 30%), screw speed (200 and 250 rpm) and barrel temperature (115 and $130^{\circ}C$). Extruded red ginseng showed higher crude saponin contents (6.72~7.18%) than raw red ginseng (5.50%). Tested extrusion conditions did not significantly affect the crude saponin content of extrudates. Increased feed moisture content resulted in increased bulk density, specific length, water absorption index (WAI), breaking strength, elastic modulus and crude protein content and decreased water solubility index (WSI) and expansion (p<0.05). Increased barrel temperature resulted in increased total sugar content, but decreased reducing sugar content in the extrudate (p<0.05). Furthermore, increased barrel temperature resulted in increased amino acid content and specific length and decreased expansion and bulk density of extrudates only at a higher feed moisture content. The physicochemical properties of extrudates were mainly dependent on the feed moisture content and barrel temperature, whereas the screw speed showed a lesser effect. These results will be used to help define optimized process conditions for controlling and predicting qualities and characteristics of extruded red ginseng.

• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.89-96
• /
• 1984

This study was intended to search the thermal properties of rice which are necessary in preventing qualitative and quantitative losses in the drying and milling processes. First, the coefficient of cubical thermal expansion of brown rice was measured, which is required for analyzing the internal stress of rice, and then theoretical thermal and moisture stresses were calculated. The results are summarized as follows: 1. The coefficient of cubical thermal expansion of brown rice was about $2.81{\times}10^{-4}/^{\circ}C$ in the temperature range of $10^{\circ}C-60^{\circ}C$. 2. When the shape of brown rice was assumed to be a sphere or a cylinder, maximum thermal stress due to temperature change of $20^{\circ}C-60^{\circ}C$ was in the range of $25-100kg/cm^2$. And maximum moisture stress was in the range of $450-650kg/cm^2$ when the drying temperature was $35^{\circ}C$, initial and final moisture contents of brown rice were 20% and 14% (w.b.), and the moisture diffusion coefficient was assumed to be $6.79{\times}10^{-4}cm^2/hr$. 3. Consequently, it was concluded that crack formation in a rice kernel is mainly caused by moisture stress.

• Korean Journal of Food Science and Technology
• /
• v.31 no.2
• /
• pp.380-384
• /
• 1999

For the effective utilization of anchovy as a food source, processing conditions of expanded anchovy snack and monolayer moisture content of the products were investigated. Ground anchovy was mixed with 50% of wheat flour, 2.5% of NaCl and 3.0% of onion. The mixture were rolled, cut, dried and finally deep-fried with soybean oil. When 50% of wheat flour was mixed with ground anchovy, expansion rate showed the highest value among the treatments and organoleptic quality of the product was also high. Dried base with 6.4% of moisture content showed the maximum expansion rate and good crispness and brittleness when fried at $200^{\circ}C$. Monolayer moisture content of the expanded products was calculated as 2.77% by BET equation.

• Journal of the Korean Society of Tobacco Science
• /
• v.17 no.2
• /
• pp.149-159
• /
• 1995

The freeze drying rate was investigated under various conditions such as pressure and moisture contents in order to establish the optimum condition for expansion of the culled flue cured tobacco lamina. The optimal pressure in the chamber to maintain the heat and mass transfer was about 0.8torr, When the moisture contents of sample was 50-60%, expanding rate was the optimum condition and the rate was 67-76%. As the thickness of the sample layers was increased, drying-rate was decreased conversely and this result seemed to be due to decline of heat and mass transfer coefficients. Differences with the position of its stalk were also observed in drying rate, and low stalk position leaves of 5 and 3 was the fastest. Key words : freeze drying, Popping, expansion tobacco.

• Journal of the Korean Society of Tobacco Science
• /
• v.19 no.1
• /
• pp.70-75
• /
• 1997

The expansive properties of leaf tobacco by nitrogen gas was investigated with cut tobacco AB3O-1, CD3L-1(NC82). Major factors for the best expansion of the tobacco by the gas were an impregnated pressure and expansion temperature. The expansion rate for AB3O-1 and CD3L-1 at 250℃, 750kg/cm2 was 96.6%, 99.4% respectively. The shred size and fineness index at 96.6% of expansion rate for AB3O-1 was almost the same as at 58.3% for CD3L-1. The time reaching at equilibrium moisture under of RH 57% was 36hr in non-treated leaf tobacco, but it was 20hr in expanded tobacco. We confirmed that total sugar contents of leaf tobacco by the expansion was decreased with 9.3∼10.9%. Total alkaloid was decreased with 17.5∼21.1% and ether extracts was declined with 4.9∼9.3%. These results suggest that the expansion method of leaf tobacco by nitrogen gas is a useful method without any serious environmental troubles. Key words : expansion, nitrogen gas, heat treatment, tobacco.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.2
• /
• pp.23-36
• /
• 1998

Moisture content of printing paper and circumstance of printing room has great influence on the printing works. We have studied on the printability of domestic art paper according to the insufficient Korea weather. As the result, we found the printability of domestic art paper are much more affect by moisture content than any other printability coefficients, especially print density and hygroexpansivity decrease with moisture content increase.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.2
• /
• pp.292-298
• /
• 2001

This study was conducted to investigate physicochemical properties of extrudates combining 4 levels of squid (0, 3, 5 and 7%) with 3 levels of defatted soy flour (0, 5, and 10%). Blends were adjusted to moisture content of 27% and then extruded in a single-screw laboratory extruder at 170rpm screw speed and 16$0^{\circ}C$ barrel temperature. The extruded materials were dried at 6$0^{\circ}C$ for 8hr to a moisture content of 3~4% and refrigerated at 4$^{\circ}C$ for 12 hour before examination for textural properties, expansion ratio, bulk density, shear force and Hunter color. Expansion ratio of extrudates decreased as squid content increased whereas bulk density and shear force increased. Expansion ratio of extrudates was not significantly different by defatted soyflour level. Bulk density of products decreased as defatted soyflour content increased but shear force of products increased as defatted soyflour content increased. In scores of sensory hedonic evaluation of snacks, appearance, flavor, texture and overall acceptability values had lowered as squid level increased. Therefore, according to materials contents on extrudates increased, nutritional contents of this products increased and also shear force and bulk density in physical properties increased whereas expansion ratio decreased.

• Science of Emotion and Sensibility
• /
• v.17 no.1
• /
• pp.93-104
• /
• 2014

This paper investigates the physical properties such as water absorption, drying and hygral expansion of moisture responded transformable fibers and their knitted fabrics including dyeing characteristics according to the different dyeing time and temperature. For this purpose, three kinds of covered filament yarn specimens using HEF and spandex as core and PET, aerocool as a covering filament were prepared. The knitted fabric specimens were made using three kinds yarn specimens and dyed with different dyeing temperature and time. The moisture absorption, drying and hygral expansion of three kinds of knitted fabric specimens were measured and discussed with yarn structure. The wearing performance of these knitted fabric specimens were also measured and discussed with yarn characteristics using FAST system. Finally, the dyeing characteristics such as dye affinity, color difference and color fastness to washing of these knitted fabric specimens were measured and discussed with different dyeing temperature and time for examining dyeing process performance of these moisture responded transformable knitted fabrics.