• Journal of the Korean Society of Combustion
• /
• v.16 no.3
• /
• pp.12-20
• /
• 2011

Oxy-coal combustion for $CO_2$ capture in coal power plants entails a mode switching from air-firing to oxyfiring. In this study, procedure of the mode switching was investigated and discussed through experiments in pilot scale facilities: (1) a 0.3 $MW_{th}$ furnace with a vertical single burner and a FGR(Flue Gas Recirculation) system (2) a 1 $MW_{th}$ furnace with horizontal 4 burners and a FGR system. Principle of the mode switching was established and performed with control of FD fan, FGR fan, ID fan and oxygen flow rates. We have found that equivalence ratio in the oxy-firing mode should be increased more than that in the air-firing to achieve stable mode switching. Control of FD, ID and FGR fans should be performed carefully in the mode switching, in the sense of complete combustion and flame attachment. Moisture contents in the ash and the flue gas recycled to the primary oxidizer stream should be removed to prevent condensation, corrosion and duct clogging.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.2
• /
• pp.75-80
• /
• 2016

There are three types of dehumidification systems : refrigeration dehumidification method, desiccant dehumidification method and hybrid dehumidification method. The first method involves removing moisture by condensation below the dew point, the second method involves absorption by a desiccant material and the last is an integration method. However, the refrigeration dehumidification system consumes too much power and controlling the humidity ratio is difficult. The desiccant dehumidification system uses less power but it has problems of environmental pollution. The hybrid dehumidification system has the disadvantage of a high initial cost. On the other hand, the energy consumption of the membrane based dehumidification system is lower than for the refrigeration dehumidification system. Also, it is an environmentally friendly technology. In this study, the performance parameters are evaluated for the dehumidification system using a hollow fiber membrane. Available area, duct side dry-bulb temperature, sweep gas flux (flow rate) and LMPD (Log Mean Pressure Difference) were used as the performance parameters.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.3
• /
• pp.228-234
• /
• 2007

Opening an ancient tomb interior can deal fair damage for preservation in long period because of high moisture. In this study, a duct-type HVAC system was installed to preserve an ancient tomb and temperature and humidity was measured to analyze heat environment. Armhole was measured to search whether an ancient tomb receives effects of vibration caused by a duct-type HVAC system. According to the measured data, temperature in an ancient tomb is kept adaptively in conservation regardless of a duct-type HVAC system installation when it rains in summer. The other side, humidity is kept adaptively in conservation when installed duct-type HVAC system. But when it is in natural state, a lot of humidity by dew condensation phenomena. So it needs a duct-type system for an ancient tomb conservation. In the case of vibration, measurement value of 3 satisfy control but Germanic DIN 4150 does not satisfy. Therefore, equip must be such that it can prevent vibration for safety.

• Journal of the Korean Institute of Rural Architecture
• /
• v.23 no.4
• /
• pp.63-71
• /
• 2021

The purpose of this study was to investigate whether the standard models for rural housing and wooden housing model have performance for hygrothermal and to propose a way of improvement relevant to hygrothermal performance for those models. All of the models to be analyzed were found to have some parts that were absent of stability in terms of performance for hygrothermal. In the process of analyzing the causes and proposing improvement measures, the following conclusions were derived. Fist, The exterior surface of the structure should be composed of a structure with good moisture permeability, and for the interior surface, a variable vapor retarder paper should be applied in consideration of the reverse condensation phenomenon in summer. Second, in terms of performance for hygrothermal, applications of external insulation plaster finish to the exterior wall or of ventilation method using a rafter vent on the roof should be avoided. Third, a rain screen method with a ventilation layer should be applied to the exterior wall, and a method of constructing ventilation layer separated from the insulation layer with a vapor retarder paper should be applied to the roof. Fourth, the application of insulation materials having capillary action, such as wood fiber insulation board or cellulose insulation board, contributes to more stable performance for hygrothermal.

• Journal of Surface Science and Engineering
• /
• v.56 no.1
• /
• pp.1-11
• /
• 2023

Lubricant-impregnated nanoporous surfaces (LIS), which is created by impregnating water-immiscible oil into nanoporous surface structure, have been explored considering wide range of application fields. Due to the lubricant impregnated in nanoporous structure, the surface shows extreme de-wetting with a high mobility of water droplets, so that various functionalities can be realized. The lubricant layer inhibits the contact of corrosive media to porous structure as well as metal substrate, thus the surface improves the corrosion resistance. The water on the surface freeze without any contact to solid porous structure, showing a low ice adhesion for de-icing an anti-icing. The extremely high mobility of water droplets on lubricant-impregnated porous surfaces also contributes the enhancement of condensation heat transfer as well as water harvesting from fog and moisture. Moreover, the bacteria adhesion on metal surface forming biofilms causing serious hygiene issues can be inhibited on the lubricantimpregnated surfaces. Despite of such superior functionalities, the lubricant-impregnated porous surface has a limitation of lubricant depletion by external flow of fluids. Therefore, extensive efforts to improve the durability of lubricant-impregnated surface are required for practical applications.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.52-59
• /
• 2015

Cross-cut disks from small diameter oak logs were thermally modified and developed to make accessories such as a brooch. However it is known that domestic oaks are refractory and it is hard to dry their cross-cut disks without any drying defects. The cross-cut disks of Quercus variabilis (7 mm long in the longitudinal direction) were forced to dry in air at two different air velocities in summer and fall season, and their drying yields were investigated. Under the same condition, the average final moisture contents (MCs) of the specimens dried in the fall were lower than those dried in the summer. The average final MCs of the small diameter specimens dried at higher air velocity were slightly lower than those at lower air velocity while those of the large diameter specimen were not influenced by the air velocity. The number of the large diameter specimens with cross checkings was higher than that of the small diameter specimen. This discrepancy between two different diameters was twice in the fall, while it was more than four times in the summer. The large diameter specimens dried at low air velocity in Summer were cross-checked most, which was attributed to repeated water condensation and evaporation due to high humidity and low air velocity.

• Tunnel and Underground Space
• /
• v.6 no.4
• /
• pp.335-341
• /
• 1996

This fundamental study analyzes the relationship between rock thermal properties and psychrometric properties in underground space and has a ultimate goal to develope technologies for predicting major environmental variables. The study is divided into 2 subjects (1) developement of a basic model for predicting temperature and humidity, (2) analysis of the validity of the model through application to a local underground storage space for military supplies. The basic model is built for the network of tunnel-shaped underground spaces. The model takes into account rock thermal properties and changes in moisture content in the air due to condensation/evaporation on the rock surface. Using lumped-parameter analytical method, heat flux from or to the surrounding rock is calculated and then the psychrometric properties(air quantity, pressure, temperature, humidity) are estimated through network simulation. The model can be utilized regardless of the tunnel type. The study site is a local storage space built in rock, mainly granite gneiss and quartz-porphyry. It is a U-shaped tunnel, 593.5m long and 6x6.5m wide. Relative humidity inside has to be strictly controlled under 55% to avoid erosion of a certain types of supplies stored in 6 chambers with the capacity of 300~1.000 ton. The thermal conductivity varies between 2.734 and 2.779W/m$^{\circ}C$ and the thermal diffusivity is in the range of 1.119 and $1.152{\times}10^{-6}\;m^2/s$ the specific heat between 910 and $920\;J/kg^{\circ}C$. Relative errors of the predicted values of dry/wet temperature and relative humidity are 0.8~3.0%, 0~7.5% and 0~7.0%, respectively. Apparent errors associated with the rock surface temperature seems to be partly due to the intrinsic limitations in the infrared thermometer used in this study.

• Journal of Biosystems Engineering
• /
• v.19 no.3
• /
• pp.232-246
• /
• 1994

This study was conducted to develop the long-tenn storage method to minimize the black spot occurred on the surface of persimmons stored in the films at low temperature. The storage experiments were done with different films and persimmon varieties at $0^{\circ}C$ storage condition for 5 months, and then the physical and chemical characteristics of persimmons were tested monthly. The results were as follows : 1. The film 160 made from zeolites showed highest performance in well storings sweet persimmons for 5 months, compared with other films by eyesight. The initial moisture condensation inside the films seemed to cause the black spots on persimmons, and the effect of the film holes was never significant to prevent the black spots. 2. The sugar content was ranged from $14^{\circ}Brix$ to $15^{\circ}Brix$ regardless of film types and persimmom varieties, and it changed little for storage of 5 months. 3. The decrease rate of persimmom weight in the film 160 and 180 was 0.3% for storage of 5 months, while those in other films reached to 2%. The decrease rate of persimmon weight was least in the film 160 and 180. 4. The hardness of Fuyu least decreased in the films 160 and 380. It was changed from 36 kg/cnf to 8-27 $kg/cm^2$, and that of Charyang was from 31 $kg/cm^2$ to 8-10 $kg/cm^2$ for storage of 5 months. The hardness of Charyang rapidly decreased as storage period increased. 5. The average rate of black spot(defect rate) of Fuyu measured by a computer image processing system was least in the film 160 by 0.5%, but those in other films was ranged from about 5% to 20% for storage of 5 months. The rate of black spot of Charyang was less than that of Fuyu among most of films. 6. The intensity, hue, and saturation in persimmon color changed according to storage period. Especially, the intensity of persimmon colors decreased as storage period increased, but it was least in the film 160. 7. An integrated long-term storage method of sweet persimmons was suggested in the basis of the experiments and literature reviews.

• Journal of Korea Entertainment Industry Association
• /
• v.15 no.3
• /
• pp.311-321
• /
• 2021

In this study, a smart switchboard for power supply of entertainment devices was developed for the following purposes. First, the heat generated when the high-temperature and humid air inside is cooled by the thermoelectric module is smoothly discharged to the outside of the switchboard, thereby maximizing the cooling effect. So, it is possible to prevent excessive temperature rise inside the switchboard. Various problems such as condensation inside the switchboard can be prevented by controlling the temperature of the switchboard in which a fire occurs due to excessive heat in summer, removing moisture due to the cooling effect, and generating heat instead of cooling in winter. Second, it is a smart switchboard control system that can reduce the salt that may permeate inside the switchboard. Third, the smart switchboard system is an IoT-controlled switchboard that collects environmental data using a variety of sensors and can remotely control devices through a smartphone, and can be easily used in various fields.

• Journal of the Korean Institute of Rural Architecture
• /
• v.24 no.4
• /
• pp.33-40
• /
• 2022

Sharehouse has been supplied as an alternative to solving the steadily increasing one-room housing problem of single-person households every year, and it is necessary to investigate the satisfaction of residents who actually live in sharehouse through P.O.E. Therefore, this study analyzed priror researches related to the existing one-person households, sharehouses, and satisfaction surveys, and summarized indicators with high relevance and frequency to derive satisfaction survey factors that can clearly evaluate the improvement architectural plan of sharehouses. As a result, it was classified into 4 items in the 'general information' category to investigate the status, housing rental type, and housing cost of the sharehouse, 15 factors in the 'peripheral environment' category to evaluate the safety, 3 factors in the 'community' category, and 17 factors in the space (facility) and service category. In the "General Information" section, the overall one-person housing satisfaction, desired sharehouse type, housing rental type, housing cost, and living expenses were reduced. In the "Surrounding Environment", accessibility to public office, accessibility to cultural facilities, accessibility to medical facilities, accessibility to work and school, convenience stores, noise pollution and safety. In addition, in the "community" section, it consists of interactions with various people, relationships with housemates and in the "space (facilities) and service" section, heating, waterproof, soundproof, ventilation, moisture and condensation blocking, facility management, interior, room size, built-in furniture, storage space, laundry, parking. Most of the scales for each factor were 5-point Likert scales, allowing evaluation of the degree of satisfaction, and some factors presented criteria to induce structured answers. Therfore, it is expected that the survey will be conducted on residents who actually live by deriving factors for the satisfaction survey of one-person households living in the sharehouse, and the current status of the sharehouse will be identified, and the degree of satisfaction will be analyzed to be used for research.