• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.6
• /
• pp.489-496
• /
• 2021

Water disinfection using UV-LED(Light emitting diode) has many advantages, such as smaller footprint and power consumption as well as relatively longer lifespan than those of conventional mercury-UV lamps. Moreover, UV-LED disinfection is considered an environmentally benign process due to its mercury-free nature. In this study, disinfection using an LED module emitting 275nm UV was carried out. 384 UV-LEDs were put into a cylinder tube with a capacity of 1.7 liters. The UV intensity of the UV-LED module was controlled from 1.7 to 8.4 mW/cm². The disinfection efficiency for the model microorganism solutions(E. coli ) was monitored. As the UV intensity(I) and contact time(t) varied, inactivation of the microorganisms from 2 to 4-log-removals(i.e., 99 to 99.99% of disinfection efficiency) was achieved. Disinfection using UV-LED was followed to 1^st order reaction and the reaction rate constant, k was determined. In addition, the relationship between UV intensity(I) and contact time(t) in order to obtain 99.99% of disinfection efficiency was modeled: I^1.2·t= 460, which indicates that the product of UV intensity and contact time requiring 4-log-removals is always constant.

• Current Photovoltaic Research
• /
• v.9 no.4
• /
• pp.123-127
• /
• 2021

This study was on electrode design for the realization of a solar cell that combines electrode formation and module integration process to overcome printing limitations. We used the passivated emitter rear contact (PERC) solar cell. Wafer size was 156.75 mm ×156.75 mm. The fabricated cell results showed that the open-circuit voltage of 649 mV, short-circuit current density of 36.15 mA/cm², fill factor of 68.5%, and efficiency of 16.06% with electrode conditions the 24BBs with the width 190 ㎛ and 90FBs with the width 45 ㎛. For improving efficiency, the characteristics of the solar cell were checked according to the change in the number of BBs and FBs and the change in line fine width. It is confirmed that the efficiency of the solar cell will be improved by increasing the number of FBs from 90 to 120, and increasing the line width of the FBs by about 10 ㎛ compared to the manufacturing solar cells.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.4
• /
• pp.277-285
• /
• 2001

We developed a compact, 10 kWe, purifier-integrated reformer which supplies hydrogen for fuel cell vehicles. Our proprietary technologies regarding hydrogen purification by palladium alloy membrane and catalytic combustion by noble metal coated wire-mesh catalyst were combined with the conventional methanol steam reforming technology, resulting in higher conversion, excellent quality of product hydrogen, and better thermal efficiency than any other systems. In this system, steam reforming, hydrogen purification, and catalytic combustion take place all in a single reactor so that the whole system is compact and easy to operate. The module produces $8.2Nm^3/hr$ of 99.999% or higher purity hydrogen with CO impurity less than 10 ppm, which is equivalent to 10 kWe when PEMFC has 45 % efficiency. Thermal efficiency of the module is 81 % and the power density of the module is 1.6 L/kWe. As the results of experiments, cold-start time has been measured about 20 minutes. Response time of hydrogen production to the change of the feed rate has been within 1 minutes.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2218-2224
• /
• 2010

Dye-sensitized solar cell (DSC) is a promising alternative solar cell to the conventional silicon solar cell due to several advantages. Development of large scale module is necessary to commercialize the DSC in the near future. A scribing technology of the transparent conductive oxide (TCO) is one of the important technologies on the fabrication of DSC module. A quality of the scribed line on the TCO has a decisive effect on the efficiency of DSC module. Among several scribing technologies, the fiber laser is a suitable for scribing the TCO more precisely and accurately because of their own characteristics. In this study, we try to improve the quality of the TCO scribed line by using the fiber laser. Consequently, the operating parameter of fiber laser is optimized to get the TCO scribed line with good quality. And the fiber laser scribing technology of the TCO is applied to the fabrication of the DSC with optimal operating parameter, operating current 3900mA. As a result, the current density and fill factor are improved and the total efficiency is increased because the internal resistances of DSC such as TCO sheet resistance and the resistance concerned to the electron movement in the $TiO_2$ are reduced. This is analyzed by the electrochemistry impedance spectroscopy (EIS) and the equivalent circuit model of the DSC.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.124-133
• /
• 2017

In the current lighting market, LEDs that have a high luminous efficiency, a long life and consume less power have emerged as next generation lighting. Owing to various designs and sizes of LEDs, the production process of existing LEDs involves many tasks that require manual labor; hence, the assembly of LEDs necessitates manpower. Because of the use of manpower, the production costs of LEDs increases and production efficiency decreases. Recently, the assembly parts of LEDs have been standardized for minimizing manual labor, and an LED is developed as an LED panel. The automatic assembly system produces LED convergent lighting by assembling two LED panels and one diffusion cover. To increase the production efficiency of the LED convergent lighting module, it is important that the development of a feeder can continuously supply the LED panels is required, and whose design has sufficient stability. The automatic assembly system of the LED convergent lighting module consists of two feeders, which convey LED panels and diffusion covers to a main conveyor, which assembles the lifted panels and covers. In this study, structural analysis and fatigue life for forced loads on the conveyer line of the feeder in the process of lifting LED panels and diffusion covers of each feeder, is analyzed. In addition, the drive of the belt constituting the conveyor line of each feeder is simulated, and the dynamic characteristics of the belt is analyzed using the virtual engineering method.

• Membrane Journal
• /
• v.27 no.5
• /
• pp.449-457
• /
• 2017

In this study, the 10 stages stacked module was designed by increasing the number of unit cells in the membrane capacitive deionization(MCDI) process. The aminated polysulfone and sulfonated poly(ether ether ketone) were synthesized and coated on porous carbon electrode by casting method. The salt removal efficiency was measured for the 10 stage stacked module under the operation conditions of adsorption voltage and time, desorption voltage and time, flow rate and concentration of feed water, and di-valent solutions including $CaSO_4$, $MgCl_2$ and tap water. Typically, when 100 mg/L of NaCl as the feed was used, the salt removal efficiency was 98.3% at a flow rate of 100 mL/min, the adsorption condition of 1.2 V/3 min and desorption condition of -0.5 V/5 min.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.5 s.48
• /
• pp.475-485
• /
• 2000

In this study, an automated optimum design program for steel box girder bridges has been developed for the optimum design of composite steel box girder bridges. The design constraints required for the optimum design of steel box girder bridges are based on the Korean standard bridge specification. Considering characteristics of steel box girder bridges, several approximation techniques, such as artificial constraint deletion, variable linking and stress reanalysis technique etc. are also introduced to enhance the efficiency of optimization. The developed program is mainly composed of major sub-system modules including structural analysis module using commercial structural analysis program such as RM-SPACEFRAME, optimum design module, pre-process module for friendly user input, and post-processor module for office automation. In addition, in order to demonstrate the efficiency and applicability of the developed optimum design program for steel box girder bridges, a few numerical examples are applied. Based on the results of the application, it may be stated that the automatic optimum design program developed in this study can be a prototype model for the developement of optimum design program for other type of bridge.

• Journal of the Korea Computer Industry Society
• /
• v.4 no.4
• /
• pp.547-552
• /
• 2003

In this thesis, interference phenomena of bluetooth networks requiring Security were minimized; strengthened security of piconet by assigning an identical PIN code to bluetooth devices, which was establishing a specific piconet during authentication stage. To establish a bluetooth piconet system. an unique ID was assigned to each bluetooth device, communication algorithms having different data formats between devices was designed, and an embedded hardware module using ARM processor and uCOS-II RTOS was implemented. About 30% of CPU efficiency in the module was increased by modifying functions including block parameters to work as nonblocking; by the increased efficiency of total piconet, the module could be used as an access point. The module could transmit maximum 10 frames of image and also audio signal by switching the packet effectively according to channel condition. By above-mentioned process, video, audio, and data could be well transmitted by the bluetooth managing program and the possibility of a commercial remote control system using bluetooth technology was suggested.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.226-232
• /
• 2005

Recently, many nation have released standard such as IEC 61000-3-2 and IEEE 59, which impose a limit on the harmonic current drawn by equipment connected to AC line in order to prevent the distortion of an AC Line. Therefore, Plasma Display Panel(PDP) which is highlightened in digital display device also has the Power Factor Correction(PFC) circuit to meet the harmonic requirements. In PDP power module, the conventional boost converter is usually used for the PFC circuit. However, it comes serious thermal problem on it's bridge diode due to heat of PDP, and therefore the system stability is not guaranteed. In this paper, the bridgeless boost converter, which is used for PFC circuit of the PDP power module, is designed and verified the possibility of the application In a practical product in a view of efficiency, component count, temperature and etc.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.11
• /
• pp.205-213
• /
• 2010

This study uses the FP-tree algorithm, one of the mining techniques. This study is an attempt to suggest a new recommended system using a modified FP-tree algorithm which yields an association rule based on frequent 2-itemsets extracted from the transaction database. The modified recommended system consists of a pre-processing module, a learning module, a recommendation module and an evaluation module. The study first makes an assessment of the modified recommended system with respect to the precision rate, recall rate, F-measure, success rate, and recommending time. Then, the efficiency of the system is compared against other recommended systems utilizing the sequential pattern mining. When compared with other recommended systems utilizing the sequential pattern mining, the modified recommended system exhibits 5 times more efficiency in learning, and 20% improvement in the recommending capacity. This result proves that the modified system has more validity than recommended systems utilizing the sequential pattern mining.