• Journal of the Korean Institute of Gas
• /
• v.25 no.1
• /
• pp.20-29
• /
• 2021

During multi-stage fracturing in a low permeable shale formation, stress interference occurs between the stages which is called the "stress shadow effect(SSE)". The effect may alter the fracture propagation direction and induce ununiform geometry. In this study, the stress shadow effect on the hydraulic fracture geometry and the well productivity were investigated by the commercial full-3D fracture model, GOHFER. In a homogeneous reservoir model, a multi-stage fracturing process was performed with or without the SSE. In addition, the fracturing was performed on two shale reservoirs with different geomechanical properties(Young's modulus and Poisson's ratio) to analyze the stress shadow effect. In the simulation results, the stress change caused by the fracture created in the previous stage switched the maximum/minimum horizontal stress and the lower productivity L-direction fracture was more dominating over the T-direction fracture. Since the Marcellus shale is more brittle than more dominating over the T-direction fracture. Since the Marcellus shale is more brittle than the relatively ductile Eagle Ford shale, the fracture width in the former was developed thicker, resulting in the larger fracture volume. And the Marcellus shale's Young's modulus is low, the stress effect is less significant than the Eagle Ford shale in the stage 2. The stress shadow effect strongly depends on not only the spacing between fractures but also the geomechanical properties. Therefore, the stress shadow effect needs to be taken into account for more accurate analysis of the fracture geometry and for more reliable prediction of the well productivity.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.217-225
• /
• 2023

2,3-Butanediol (2,3-BDO), which is used in various fields such as cosmetics and fertilizers, is a high value-added substance and the demand for it is gradually increasing. 2,3-BDO produced from the fermentation of microorganisms not only contains by-products of fermentation, but also varies greatly in feed composition depending on fermentation conditions, so it is difficult to efficiently operate the separation process to reach the target purity of the product. Therefore, in this study, through dynamic optimization of the bio-based 2,3-BDO distillation process, the optimal control route was explored to control the 2,3-BDO concentration of the bottom product to 99 wt% or more, when feed concentration changes. Steady and dynamic state process simulation, proportional integral (PI) controller design, and dynamic optimization were sequentially performed. As a result, the error between the 2,3-BDO concentration and the set point of the bottom product was reduced by 75.2%.

• Journal of KIISE:Computing Practices and Letters
• /
• v.6 no.4
• /
• pp.421-429
• /
• 2000

In present, ATM integrated switching system has been developed to a mixed modules that complexed switching system including maintenance, operation based on B-ISDN/LAN service and plug-in module, , which runs on workstation computer system. Meanwhile, workstation has HMI operation system feature including file system management, time management, graphic processing, TMN agent function. The workstation has communicated with between ATM switching module and clients. This computer system architecture has much burden messages communication among processes or processor. These messages communication consume system resources which are socket, message queue, IO device files, regular files, and so on. Therefore, in this paper we proposed new performance modeling with this system architecture. We will analyze the system bottleneck and improve system performance. In addition, in the future, the system has many additional features should be migrated to workstation system, we need previously to evaluate system bottleneck and redesign it. In performance model, we use queueing network model and the simulation package is used PDQ and C-program.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6D
• /
• pp.779-784
• /
• 2011

Freeway FFS (Free-Flow Speed) under the state of LOS (Level of Service) A has been regarded as a homogeneous state to all levels of traffic volume. The features of low-density FFS is served as the basic data for a decision on limited maximal speed, accident analysis, simulation modeling etc. A few researches for the macroscopic characteristics of design and operation speed have been reported, and any study for the microscopic features of freeway free-flow speed under the state of low density has not been done. Therefore, the characteristics of low-density FFS according to the level of traffic volume (1-3 veh/30 sec) and daily hour periods (0-5, 6-8, 9-11, 12-19, 20-23) is microscopically analyzed in this study with huge volume and speed data. It was found that speed distributions are changed and show different behaviors under the conditions of traffic volume levels and daily time periods. V85s (85th percentile speed) at early morning and night periods decrease when levels of traffic volume increase, whereas V85s at day time do not show considerable differences. Especially, FFSs of levels of traffic volume at early morning and night periods, despite low density, is analyzed as heterogeneity, but homogeneity at day time.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1173-1182
• /
• 2000

The rapid mixing process has been considered as an important step in water treatment. Since the coagulant dispersion into raw water by rapid mixer can influence on the flocculation and filtration efficiency, many researchers have developed various devices and mixing methodologies. Until now, they focused attention on only coagulant dose, pH. rotating velocity and G value but overlooked the real turbulent flow and mixer geometry in rapid mixer. Therefore this paper questions the significance of turbulent flows in rapid mixer and focuses on the analysis of turbulent fluid in various mixer geometry with CFD(Computational Fluid Dynamics). The results of the jar-tests using various geometries indicate that the turbidity removal rate in a circular jar without baffle is higher than that of a circular with baffle. And the turbidity removal rate in Hudson jar is also founded to be higher than in the circular jar with baffle. The CFD simulation of velocity fields in jar demonstrates that the differences of removal rates among the various geometries are largely due to the formation of the different turbulent fluids fields with different geometries.

• Tribology and Lubricants
• /
• v.36 no.2
• /
• pp.105-115
• /
• 2020

This paper presents a numerical study on the rotordynamic analysis of a dual-spool turbofan engine in the context of blade defect events. The blades of an axial-type aeroengine are typically well aligned during the compressor and turbine stages. However, they are sometimes exposed to damage, partially or entirely, for several operational reasons, such as cracks due to foreign objects, burns from the combustion gas, and corrosion due to oxygen in the air. Herein, we designed a dual-spool rotor using the commercial 3D modeling software CATIA to simulate blade defects in the turbofan engine. We utilized the rotordynamic parameters to create two finite element Euler-Bernoulli beam models connected by means of an inter-rotor bearing. We then applied the unbalanced forces induced by the mass eccentricities of the blades to the following selected scenarios: 1) fully balanced, 2) crack in the low-pressure compressor (LPC) and high pressure compressor (HPC), 3) burn on the high-pressure turbine (HPT) and low pressure compressor, 4) corrosion of the LPC, and 5) corrosion of the HPC. Additionally, we obtained the transient and steady-state responses of the overall rotor nodes using the Runge-Kutta numerical integration method, and employed model reduction techniques such as component mode synthesis to enhance the computational efficiency of the process. The simulation results indicate that the high-vibration status of the rotor commences beyond 10,000 rpm, which is identified as the first critical speed of the lower speed rotor. Moreover, we monitored the unbalanced stages near the inter-rotor bearing, which prominently influences the overall rotordynamic status, and the corrosion of the HPC to prevent further instability. The high-speed range operation (>13,000 rpm) coupled with HPC/HPT blade defects possibly presents a rotor-case contact problem that can lead to catastrophic failure.

• Environmental and Resource Economics Review
• /
• v.21 no.1
• /
• pp.27-67
• /
• 2012

This paper analyzed the effect of transaction costs on the prices and trading volumes at the initial stage of emission markets and also examined how the size of the effect differs depending on the characteristics of the transactions. We built trading protocols modeling a recursive process to search the trading partner and make transactions with several behavioral assumptions considering the situations of early markets. The simulations results show that adding transaction costs resulted in reduction of trading volumes. Furthermore, the speed of reduction in trading volume to the increase of transaction costs is higher when there is scale economy. With a certain level of scale economy, the trading volumes abruptly fall down to almost zero as the transaction cost gets over a certain level. This suggests the possibility of a failed market. Since the scale economy is thought to be significant in the early stage of emission trading market, it is desirable to design a trading system that maximizes trading volumes and minimizes unit transaction costs at the outset. One of the alternatives to meet these conditions is to establish a centralized exchange and take measures to increase trading volumes.

• Applied Biological Chemistry
• /
• v.43 no.2
• /
• pp.116-123
• /
• 2000

A numerical model of three-dimensional soil water distribution for drip irrigation management under cropped conditions was developed using Richards equation in Cartesian coordinates. The model accounts for both seasonal and diurnal changes in evaporation and transpiration, and the growth of plant root and the shape of root zone. Solutions were numerically approximated using the Crank-Nicolson implicit finite difference technique on the block-centered grid system and the Gauss-Seidel elimination in tandem. The model was tested under several conditions to allow the flow rates and configurations of drip emitters vary. In general, simulation results agreed well with experimental results and were as follows. The velocity of soil-water flow decreased drastically with distance from the drip source, and the rate of expansion of the wetted zone decreased rapidly during irrigation. The wetting front of wetted zone from a surface drip emitter traveled farther in vertical direction than in horizontal direction. Under this experimental weather condition, water use efficiency of a drip-irrigated apple field was greatest for 4-drip-emitter system buried at 25 cm, resulting from 10% increase in transpiration but 20% reduction in soil evaporation compared to those for surface 1-drip emitter system. Soil moisture retention curve obtained using disk tension infiltrometer showed significant difference from the curve obtained with pressure plate extractor.

• Journal of Korea Water Resources Association
• /
• v.31 no.1
• /
• pp.35-44
• /
• 1998

An integrated system of GIS and water quality model was suggested including the pollutant loads from the watershed. The developed system consists of two parts. First part is the GIS module. The geographic information system of the study area was built to provide the information on landuse and several surface factors concerning the overland flow processes of water and pollutants. Second part is the modeling modules which include storm event pollutant load model(SEPLM)., non-storm event pollutant load model(NSPLM), and river water quality simulation model(RWQSM). Models can calculate the pollutant load from the study area. The databases and models are linked through the interface modules resided in the overall system, which incorporate the graphical display modules and the operating scheme for the optimal use of the system. The developed system was applied to the Chungju multi-purpose reservoir to estimate the pollutant load during the four selected rainfall events between 1991 and 1993,. based upon monthly basis and seasonal basis in drought flow, low flow, normal flow and wet flow.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5550-5558
• /
• 2015

Recently, fuel cell with high energy efficiency and low CO2 emission is energetically interconnected with power system. Especially, FCGS(Fuel Cell Generation System) which usually operates at high temperature, is being developed and installed in the form of large scale system. However, it is reported that power system disturbances related to surge, harmonic and EMI have caused several problems such as malfunction of protection device and damage of control device in the large scale FCGS. In order to solve these problems, this paper presents a modeling of operation characteristics of FCGS by PSCAD/EMTDC, ETAP, P-SIM software. And also, this paper proposes countermeasure algorithms to prevent power system disturbances. From the simulation results, it is confirmed that the proposed algorithm is useful method for the stable operation of large scale FCGS.