• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.163-168
• /
• 2000

A method to search the design parameters for optimum stage matching has been used based on a 1-D mathematical model of a compressor, which uses the data obtained from the preliminary test to identify the design parameters. This methodology was applied with a two-stage axial compressor, which was originally designed for a helicopter gas turbine engine. After Identifying design parameters using preliminary test data, an optimization process has been employed to achieve the best matching between the stages (i.e., maximum efficiency of the compressor at its operation modes within a given range of the rotor speed under given restrictions for required stall margins and mass flow). 3-D flow calculations have been performed to confirm the usefulness of the corrections based on 1-D mathematical model. Calculational results agree well with the experimental data in view of the performance characteristics. Some promising results were produced through the methodology proposed in this paper in conjunction with flow calculations.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.197-207
• /
• 2004

The developing Smart UAV in KARI supposes high speed flight as like a conventional plane, as well as vertical takeoff and landing as like a helicopter. Therefore, the air intake system should be designed to provide the sufficient air flow to the engine and the maximum possible total pressure recovery at the engine intake screen over a wide range of flight conditions. For this purpose, we designed the intake system using a pitor type intake model and plenum chamber. In this paper, we designed the intake model and analyzed the performance of designed intake system using the general-purpose commercial CFD code, CFD-ACE+. The analysis results of the total pressure variation and the velocity distribution were illustrated in this paper. The pressure recovery and distortion coefficient at a plane coincident with the compressor inlet were calculated and streamline variation through the intake system was investigated at the worst flight condition as well as the standard flight condition.

• Journal of computational fluids engineering
• /
• v.17 no.1
• /
• pp.54-60
• /
• 2012

Transition prediction results are validated with experimental data obtained from a transonic wind tunnel for the KU109C airfoil. A Reynolds-Averaged Navier-Stokes code is simultaneously coupled with the transition transport model of Langtry and Menter and applied to the numerical prediction of aerodynamic performance of the KU109C airfoil. Drag coefficients from the experiment are better correlated to the numerical prediction results using a transition transport model rather than the fully turbulent simulation results. Maximum lift coefficient and drag divergence at the zero-lift condition with Mach number are investigated. Through the present validation procedure, the accuracy and usefulness of both the experiment and the numerical prediction are assessed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.4
• /
• pp.19-26
• /
• 2003

In this paper, the result of the conceptual study of a tipjet driven propulsion system is presented. The concept of a tipjet driven propulsion system is to employ tipjet as power source to drive a rotor Because the vehicle is supposed to takeoff and land vertically, a rotor system, which has tipjet nozzles, is adopted to fly like a helicopter. Exhaust gas, which is generated by an engine, Passes through an internal duct system and divided into four blade ducts. The design code is consists of two parts, engine model and internal duct model. Inside a rotating duct, compressible flow is affected by two additional force terms, centrifugal force and coriolis force and they govern the performance in rotary mode, The intention of this paper is to address the issues associated with sizing and optimizing configurations of a tipjet driven propulsion system especially in rotary wing mode.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.3
• /
• pp.298-303
• /
• 2004

This paper deals with a stochastic stabilization of observer-based output-feedback control Takagi-Sugeno (T-S) fuzzy system with Markovian input delay. The finite Markovian process is adopted to model the input delay of the overall control system. It is assumed that the zero and hold devices are used for control input. The continuous-time T-S fuzzy system with the Markovian input delay is discretized for easy handling delay, accordingly, the discretized T-S fuzzy system is represented by a discrete-time T-S fuzzy system with jumping parameters. The stochastic stabilizability of the jump T-S fuzzy system is derived and formulated in terms of linear matrix inequalities (LMIs). The usefulness of the proposed algorithm is also certificated by simulation of 2 degree of freedom helicopter model.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.11
• /
• pp.1056-1060
• /
• 2010

The software running on avionic systems is required to be highly reliable and productive. Due to these demands, the standard such as ARINC 653 has been suggested, which includes the abstraction of resource partitioning and defines interfaces between avionic operating system and applications. Though there are many manned aerial vehicles employing ARINC 653 based operating systems, Linux-based ARINC 653 for unmanned aerial vehicles has not been studied yet. In this paper, we propose the design of Linux-based ARINC 653 process model and present preliminary implementation. The experiment results present that the implementation is enough to support control software of unmanned helicopter.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.32-41
• /
• 2009

In this study, scale-down design of full-scale Korean Utility Helicopter (KUH) main rotor blade has been investigated. The scaled model system were designed for the measurement of aerodynamic performance, tip vortex and noise source. For the purpose of considering the same aerodynamic loads, the Mach-scale method has been applied. The Mach-scaled model has the same tip Mach number, and it also has the same normalized frequencies. That is, the Mach-scaled model is analogous to full-scale model in the view point of aerodynamics and structural dynamics. Aerodynamic scale-down process could be completed just by adjusting scaling dimensions and increasing rotating speed. In the field of structural dynamics, design process could be finished by confirming the rotating frequencies of the designed blade with the stiffness and inertial properties distributions produced by sectional design. In this study, small-scaled blade sectional design were performed by applying domestic composite prepregs and structural dynamic characteristics of designed model has been investigated.

• Journal of Communications and Networks
• /
• v.17 no.1
• /
• pp.58-66
• /
• 2015

Aeronautical communication networks (ACN) is an emerging concept in which aeronautical stations (AS) are considered as a part of multi-tier network for the future wireless communication system. An AS could be a commercial plane, helicopter, or any other low orbit station, i.e., Unmanned air vehicle, high altitude platform. The goal of ACN is to provide high throughput and cost effective communication network for aeronautical applications (i.e., Air traffic control (ATC), air traffic management (ATM) communications, and commercial in-flight Internet activities), and terrestrial networks by using aeronautical platforms as a backbone. In this paper, we investigate the issues about connectivity, throughput, and delay in ACN. First, topology of ACN is presented as a simple mobile ad hoc network and connectivity analysis is provided. Then, by using information obtained from connectivity analysis, we investigate two communication models, i.e., single-hop and two-hop, in which each source AS is communicating with its destination AS with or without the help of intermediate relay AS, respectively. In our throughput analysis, we use the method of finding the maximum number of concurrent successful transmissions to derive ACN throughput upper bounds for the two communication models. We conclude that the two-hop model achieves greater throughput scaling than the single-hop model for ACN and multi-hop models cannot achieve better throughput scaling than two-hop model. Furthermore, since delay issue is more salient in two-hop communication, we characterize the delay performance and derive the closed-form average end-to-end delay for the two-hop model. Finally, computer simulations are performed and it is shown that ACN is robust in terms of throughput and delay performances.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.2
• /
• pp.186-196
• /
• 2017

In order to resolve the trimming difficulty in rotor CFD calculations, a high-efficiency and improved "delta trim method" is established to compute the blade control settings that are necessary to identify the blade motion. In this method, a simplified model which combines the blade element theory and different inflow models is employed to calculate the control settings according to the target aerodynamic forces, then it is coupled into a CFD solver with unsteady Navier-Stokes equations by the delta methodology, which makes the control settings and aerodynamics calculated and updated in the meantime at every trim cycle. Different from the previous work, the current research combines the inflow model based on prescribed wake theory. Using the method established, the control settings and aerodynamic characteristics of Helishape 7A, AH-1G and Caradonna-Tung rotors are calculated. The influence of different inflow models on trimming calculations is analyzed and the computational efficiency of the current "delta trim method" is compared with that of the "CFD-based trim method". Furthermore, for the sake of improving the calculation efficiency, a novel acceleration factor method is introduced to accelerate the trimming process. From the numerical cases, it is demonstrated that the current "delta trim method" has higher computational efficiency than "CFD-based trim method" in both hover and forward flight, and up to 70% of the amount of calculation can be saved by current "delta trim method" which turns out to be satisfactory for engineering applications. In addition, the proposed acceleration factor shows a good ability to accelerate the trim procedure, and the prescribed wake inflow model is always of better stability than other simple inflow models whether the acceleration factor is utilized in trimming calculations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.6
• /
• pp.530-536
• /
• 2016

The handling quality simulator including high fidelity flight mechanics model is indispensable component to design and verify the flight control system. Korea Aerospace Industries, LTD. (KAI) has been performing LCH (Light Civil Helicopter) core technology development program regarding automatic flight control system (AFCS) software development. And KAI has been developing flight mechanics model using FLIGHTLAB to design and evaluate the AFCS flight control law. This paper presents the handling quality assessment environment development results through the combining FLIGHTLAB with a legacy simulator. And this paper details the FLIGHTLAB model, application development process and FLIGHTLAB interface design. The developed handling quality assessment environment has been demonstrated with the ADS-33E hover and pirouette MTE (Mission Task Element) maneuver simulation.