• ETRI Journal
• /
• v.39 no.3
• /
• pp.336-344
• /
• 2017

In this paper, we propose a convenient microwave orbital angular momentum (OAM) mode generation and multiplexing method operating in the 18 GHz frequency band, based on a $2{\times}2$ uniform circular array and a $4{\times}4$ Butler matrix. The three OAM modes -1, 0, and +1 were generated and verified using spatial S-parameter measurements; the measured back-to-back mode isolation was greater than 17 dB in the full 17 GHz to 19 GHz range. However, the radiated OAM beam centers were slightly dislocated and varied with both frequency and the mode index, because of the non-ideal characteristics of the Butler matrix. This resulted in mode isolation degradation and transmission distance limitations.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.405-412
• /
• 2013

This paper reports the steady-state stresses within the heat affected zone (HAZ) of a welded straight pipe subject to creep. The creep constants and exponent are varied systematically to see the effect of various mismatches in creep properties on the steady-state creep stresses, via detailed two-dimensional finite element (FE) creep analyses. The weldments consist of the base metal and weld metal with the HAZ, which are characterized using the idealized power creep laws with the same creep exponent. The internal pressure and axial loading are considered to see the effect of the loading mode. To quantify the creep stresses, a creep mismatch factor is introduced as a function of the creep constants and exponent. It is concluded that the ratio of the section-averaged stresses for a mismatched case to those for an evenmatched case are linearly dependent on the mismatch factor. The results are compared with the FE results, including the Type IV region, as well as the R5 procedure.

• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.125-134
• /
• 2014

This paper presents a robust and speed-sensorless stator flux estimation for induction motor direct torque control. The proposed observer is based on sliding mode approach. Stator electrical equations are used in the rotor orientation reference frame to eliminate the observer dependence on rotor speed. Lyapunov's concept for systems stability is adopted to confine the observer gain. Furthermore, the sensitivity of the observer to parameter mismatch is recovered with an adaptation technique. The nonlinearities of the pulse width modulation voltage source inverter are estimated and compensated to enhance stability at low speeds. Therefore, a new method based on the model reference adaptive system is proposed. Simulation and experimental results are shown to verify the feasibility and effectiveness of the proposed algorithms.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.364-372
• /
• 2016

In this paper, a voltage controller for the seamless transition of a grid-connected inverter for ESS is proposed. The single-phase inverter is operated as a current controller when the grid is connected and as a voltage controller in the stand-alone mode when the grid is disconnected. Generally, in the case of grid recovery, the overcurrent may flow into the system because of the mismatch phase between the inverter output and grid voltages. The proposed controller resolves the overcurrent problem through phase delay problems with initial value feed-forward control of the integrator when the grid voltage is restored. The effects of the control method are simulated through PSIM, and the usefulness of the control method is verified through experiments.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1593-1599
• /
• 2017

This paper presents a multi-channel light-emitting diode (LED) driver IC with a current-mode current regulator. The proposed current regulator replaces resistors for current sensing with a sequentially controlled single current sensor and a single regulation loop for sensing and regulating all LED channel currents. This minimizes the current mismatch among the LED channels and increases voltage headroom or, equivalently, power efficiency. The proposed LED driver IC was fabricated in a $0.35-{\mu}m$ BCD 60-V high voltage process, and the chip area is $1.06mm^2$. The measured maximum power efficiency is 93.4 % from a 12-V input, and the inter-channel current error is smaller than as low as ${\pm}1.3%$ in overall operating region.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.5
• /
• pp.212-221
• /
• 1996

A CMOS comparator is designed for low voltage and low power operations. The proposed comparator consists of a preadmplifier followed by a regenerative latch. The preasmplifier reduces the power consumption to a half with the power-down mode and the dynamic offsets of the latch, which is affected by each device mismatch, is statistically analyzed. The circuit is designed and simulated using a 0.8.mu.m n-well CMOS process and the dissipated power is 0.16mW at a 20MHz clock speed based on a 3V supply.

• ETRI Journal
• /
• v.27 no.1
• /
• pp.95-101
• /
• 2005

Waveguide structures of the stand-alone electroabsorption (EA) modulator and the electroabsorption modulated laser (EML) are investigated using the 3D beam propagation method. The EA waveguide structures with InP-based passivation layers show saturation in the extinction ratio (ER) due to the stray light traveling through the passivation layers. This paper demonstrates that narrower passivation layers suppress stray-light excitation in the EA waveguide, increasing the ER. A taper structure in the isolation section of the EML waveguide can reduce the mode mismatch and suppress the excitation of the stray light, increasing the ER further. Low-index-polymer passivation layers can confine the mode more tightly in the active waveguide, yielding an even higher ER.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.518-521
• /
• 1998

This paper describes a 3.3V-65MHz 12BIT CMOS current-mode DAC designed with a 8 MSB current matirx stage and a 4 LSB binary weighting stage. The linearity errors caused by a voltage drop of the ground line and a threshold voltage mismatch of transistors have been reduced by the symmetrical routing method with ground line and the tree structure bias circuit, respectively. In order to realize a low glitch energy, a cascode current switch ahs been employed. The simulation results of the designed DAC show a coversion rate of 65MHz, a powr dissipation of 71.7mW, a DNL of .+-.0.2LSB and an INL of .+-.0.8LSB with a single powr supply of 3.3V for a CMOS 0.6.mu.m n-well technology.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.11
• /
• pp.4519-4533
• /
• 2015

Hypertext Transfer Protocol (HTTP) adaptive streaming has become a new trend in video delivery. An HTTP adaptive streaming client needs to effectively estimate resource availability and demand. However, due to the bitrate of the video encoded in variable bitrate (VBR) mode, a bitrate mismatch problem occurs. With the rising demand for mobile devices, the likelihood of cases where two or more HTTP adaptive streaming clients share the same network bottleneck and competing for available bandwidth will increase. These mismatch and competition issues lead to network congestion, which adversely affects the Quality of Experience (QoE). To solve these problem, we propose a video rate adaptation scheme for the HTTP video streaming to guarantee and optimize the QoE. The proposed scheme estimates the available bandwidth according to the bitrate of each segment and also schedules the segment request time to expedite the response to the bandwidth variation. We used a multi-client simulation to prove that our scheme can effectively cope with drastic changes in the connection throughput and video bitrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.924-930
• /
• 1998

In this study, we describe the properties of an electro-optical modulator with CPW(coplanar waveguide) electrode fabricated on $LiNvO_3$ optical waveguide, that is applicable to optical communications. These optical modulators have features that use a buffer layer to reduce velocity mismatch between microwaves and optical wave as well as employ CPW to improve impedance and propagation mode mismatch between the electrode and the external circuits. And an annealed proton exchange technique for obtaining low-loss optical waveguides and good reproducibility was employed. Taking into consideration the mentioned background, to achieve the lower driving voltage of optical modulator, we have re-disigned the longer interaction length. And their device properties are discussed also. As a result, fabricated optical modulators of good 10Gps operation and low voltage(5.6V of the halfwave lengfth voltage) at an $1.5{\mu}m$ wavelength are achived with good reproducibility.