• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.5
• /
• pp.431-437
• /
• 2012

PV simulators are essential equipment for testing power conditioning systems (PCS) which are one of an important part in PV generator systems, for testing before shipment. High dynamic PV simulator is required since MPPT(Maximum Power Point Tracking) test procedure has been established by EN50530 regulation recently. Most high quality PV simulator prevailed in the market is linear type which however has low efficiency. This paper proposes design guide lines for the power stage and LCL type filter cooperating with a switching mode PV simulator that shows high efficiency and very low power consumption. Proposed theory is verified by experiment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.131-137
• /
• 2003

We have performed computer simulation to obtain electro-optic chracteristics of reflective liquid crystal display (LCD) using wide viewing angle LC mode, fringe field switching(FFS). Unlike other reflective LCD modes, in the FFS mode, the LC director in plance so an application to reflective display consisted of polarizer, LC layer and reflector is possible. when an incident light is 550mm, the optimal cell retardation value is 0.1365${\mu}$m and the efficiency of reflectivity is high over 90% with very little wavelength dispersion. Further, we have studied a new reflective display with polarizer, optical compensation film with half plate, LC plus reflector. The display with optimized cell parameters shows high contrast ratio (CR) over 130 with high light efficiency over 90% at normal direction and the CR greater than 5 exists over 60$^{\circ}$ of polar angle in all directions.

• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.342-350
• /
• 2010

Randomizing the switching frequency (RSF) to reduce the electromagnetic interference (EMI) of switching power converters is a well-known technique that has been previously discussed. The randomized pulse position (RPP) technique, in which the switching frequency is kept fixed while the pulse position (the delay from the starting of the switching cycle to the turn-on instant within the cycle) is randomized, has been previously addressed in the literature for the same purpose. This paper presents a double-hybrid technique (DHB) for EMI reduction in dc-dc switching regulators. The proposed technique employed both the RSF and the RPP techniques. To effectively spread the conducted-noise frequency spectrum and at the same time attain a satisfactory output voltage quality, two parameters (switching frequency and pulse position) were randomized, and a third parameter (the duty ratio) was controlled by a digital compensator. Implementation was achieved using field programmable gate array (FPGA) technology, which is increasingly being adopted in industrial electronic applications. To evaluate the contribution of the proposed DHB technique, investigations were carried out for each basic PWM, RPP, RSF, and DHB technique. Then a comparison was made of the performances achieved. The experimentally investigated features include the effect of each technique on the common-mode, differential-mode, and total conducted-noise characteristics, and their influence on the converter’s output ripple voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.9A
• /
• pp.892-899
• /
• 2006

In this paper, we propose an automatic switching technology between the ad-hoc and the infrastructure modes without user intervention in the IEEE 802.11b wireless LAN. Also, we design our proposed technology and implemented on the Linux machine. For this operation, the area within an Access Point (AP) coverage is defined as a switching area, and a node without any transmission in this area is assumed to be able to relay frames between the AP and nodes in the shaded area that is outside the coverage and cannot reach the AP. By using the proposed technology, it is possible to provide the seamless Internet access service to nodes at the ad-hoc mode in the shaded area. In this paper, we explains the operation of the detection method of the switching area, presents the flowchart and implementation environment. To prove the operation of our technology, we obtain the results of captured packets transmitted between nodes and throughput results through ftp transmission experiment. Hence, we can see that our proposed scheme can be improve the wireless access service in wireless and mobile networks.

• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.105-114
• /
• 2014

The sliding mode control (SMC) strategy is applied to a permanent magnet synchronous machine vector control system in this study to improve system robustness amid parameter changes and disturbances. In view of the intrinsic chattering of SMC, a current sliding mode control method with a load sliding mode observer is proposed. In this method, a current sliding mode control law based on variable exponent reaching law is deduced to overcome the disadvantage of the regular exponent reaching law being incapable of approaching the origin. A load torque-sliding mode observer with an adaptive switching gain is introduced to observe load disturbance and increase the minimum switching gain with the increase in the range of load disturbance, which intensifies system chattering. The load disturbance observed value is then applied to the output side of the current sliding mode controller as feed-forward compensation. Simulation and experimental results show that the designed method enhances system robustness amid load disturbance and effectively alleviates system chattering.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1757-1758
• /
• 2006

This paper considers a method to design sliding mode observers for a class of uncertain systems using Linear Matrix Inequalities(LMI). In an LMI-based sliding mode observer design method for a class of uncertain systems the switching surface is set to be the difference between the observer and system output. In terms of LMIs, a necessary and sufficient condition is derived for the existence of a sliding-mode observer guaranteeing a stable sliding motion on the switching surface. The gain matrices of the sliding-mode observer are characterized using the solution of the LMI existence condition. The results are illustrated by an example.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.600-603
• /
• 2009

The liquid crystal device with switchable dynamic mode and memory mode has been investigated and developed. The proposed device reveals splay, ${\pi}$ twist and bend states by selective switching among them. In the dynamic mode, this device is operated in the bend state which exhibits the wide view angle and fast response time properties due to the self-compensated bend structure and flow accelerated fast response time. In the memory mode, the permanent memory characteristics in the splay and ${\pi}$ twist sates are obtained, respectively. The switching mechanisms of the tristate device are also proposed.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.337-338
• /
• 2013

Combination the several type of single phase power conversion utilized simply topology are proposed in this paper. Totally four kind of converter are investigated, they are Boost AC/AC Converter, Buck AC/AC Converter, Boost AC/DC Converter, and Buck DC/AC Converter. Two types action mode are presented to determine the functional of circuit. First is AC chopper action mode, representation of the AC/AC converter. AC chopper action mode offered the sinusoidal current waveform, better power factor, faster dynamics, and smaller input/output filter. They present high robustness, offer safe commutation and have high efficiency. The second is full bridge action mode, determined the transformation AC to DC power and otherwise. Four switching devices and one magnetic contactor will establish the mode operation of circuit and manage the flow of power proceed in proper. The correction and advance of the kind of converter are verified by simulation.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2145-2147
• /
• 1998

This paper presents a Class-D type switched mode audio power amplifier employing ZVT(Zero-Voltage-Transition) soft switching technique. In order to obtain a wide bandwidth and lower distortion for an audio amplifier a high switching frequency is essential. The ZVT switching scheme enables a high frequency switching without sacrificing the efficiency much as in a hard switching. A prototype amplifier is built to demonstrate the feasibility of this technique for the audio power amplifier.

• Proceedings of the IEEK Conference
• /
• 2001.06e
• /
• pp.249-252
• /
• 2001

A large number of soft switching topologies included a resonant circuit have been proposed. But these circuits increase number of switch in circuit and complicate sequence of switching operation. In this Paper, the authors propose power conversion system, DC-AC inverter of high efficiency and high power factor with soft switching mode by partial resonant method. The result is that the switching loss is very low and the efficiency of system is high. And the snubber condenser used in partial resonant circuit makes charging energy regenerated at input power source for resonant operation.