• Earthquakes and Structures
• /
• 제6권4호
• /
• pp.393-408
• /
• 2014

In this paper, a direct identification of modal parameters using the continuous wavelet transform is proposed. The purpose of this method is to transform the differential equations of motion into a system of algebraic linear equations whose unknown coefficients are modal parameters. The efficiency of the present method is confirmed by numerical data, without and with noise contamination, simulated from a discrete forced system with four degrees-of-freedom (4DOF) proportionally damped.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1995년도 가을 학술발표회 논문집
• /
• pp.87-94
• /
• 1995

In highway bridges robust damage detection exercises are mandatory to secure the safety of the structures from hostile environmental conditions such as fatigue earthquake, wind, and corrosion. This paper presents a damage detection practice in a full-scale highway bridge by utilizing modal response parameters of as-built and damaged states of the structure. first the test structure is described and modal testing procedures are outlined. Next, a damage detection model which yields information on the location of damage directly from changes in mode shapes is outlined. Finally, the damage detection model is implemented to predict the location of damage in the ten structure. From the results, it was found that the damage detection model accurately locates damage in the test structures for which modal parameters of only a single mode are available for pre-damage (as-built) and post-damage stages.

• 한국지진공학회논문집
• /
• 제14권2호
• /
• pp.67-74
• /
• 2010

비닐하우스 아치구조에 고정햄머 및 이동가속도계 형식을 취한 충격진동실험을 수행하여 획득한 일련의 진동기록으로 부터 고유진동수, 감쇠율 및 모드형태 등과 같은 모달계수를 추출하기 위하여 최신 고급 주파수영역 시스템판별법인 PolyMAX 및 FDD를 적용하였다. 전자는 입력-출력 데이터 모두를 사용하며, 후자는 출력 데이터 만 을 사용한다. 본 연구의 비닐하우스 강재 파이프 아치와 같이 매우 세장한 구조물에 진동계측 등과 같은 비파괴 실험기법을 적용하여 정적좌굴 하중을 결정할 수 있는 지 여부 및 손상을 감지할 수 있는지 등에 대하여 중점적으로 조사하였다. 대체로 추출한 모달계수는 유한요소해석으로부터 획득한 결과와 좋은 일치를 나타냈으며, 지속적으로 수행 할 후속연구에 가능성을 제시하였다.

• 대한조선학회논문집
• /
• 제55권1호
• /
• pp.37-44
• /
• 2018

To understand the dynamic characteristics of the vessel with hydroelastic response, it is very important to estimate the dynamic modal parameters such as mode shapes, natural frequency, and damping ratio. These dynamic modal parameters of full scale ship are a priori unknowns, hence to be estimated directly based upon the full scale measurement data. In this paper, dynamic modal parameters were extracted by signal processing of acceleration and strain data measured from a large container ship whose loading capacity is 9400TEU. The mode shapes of the vibrating hull were identified using the proper orthogonal decomposition and the vibration response of hull was decomposed into its modal magnitudes. Natural frequencies of specific modes were derived via Fourier transform of these modal magnitude. Also, the free decay signal of the vibrating hull was obtained through the random decrement technique and the damping ratio was estimated with accuracy.

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.707-717
• /
• 2006

근래에 들어 기존의 PSC 거더 교량 외에 다양한 형태의 교량이 개발되고 있으며, 다단계 긴장에 의한 PSC 거더교는 대표적인 예이다. 다단계 긴장 PSC 거더교는 구조적 개념에 따라 자중을 줄이고 경간을 장대화할 수 있는 장점을 갖고 있다. 그러나, 이와 같은 장대화된 보다 유연한 교량은 구조적 안전성 및 사용성을 고려한 주행열차하중에 대한 동적거동 검토가 필수적이며, 철도교량의 주행열차하중에 대한 동적성능평가를 위한 정확한 동특성 입력은 매우 중요하다. 본 연구에서는 정확한 고유진동수 및 감쇠비 추출을 위하여 25m 실물 다단계 긴장 PSC 거더를 제작하여 시공단계별 모달테스트를 수행하였다. 모달테스트를 위한 가진방법으로 기존의 충격햄머에 의한 방법 외에 디지털 콘트롤에 의한 가진기를 사용하여 보다 정확한 주파수응답 함수를 얻고자 하였다. 또한, 시공단계별 구조계 변화 및 긴장에 의한 동특성 변화를 고찰하기 위하여 시공단계별 실험을 수행하였다. 모달테스트 결과에 의한 동특성 값을 주행열차하중 해석에 적용하여 다양한 매개변수연구를 통한 철도교량 동적성능평가를 수행하였다. 동적처짐, 충격계수, 바닥판의 연직가속도, 단부꺾임각 등에 대하여 열차별, 속도별 동적해석을 수행하여 국내외 철도교량 동적성능 평가기준과 비교하였다.

• Smart Structures and Systems
• /
• 제10권4_5호
• /
• pp.427-442
• /
• 2012

An effective approach for updating finite element model is presented which can provide reliable estimates for structural updating parameters from identified operational modal data. On the basis of the dynamic perturbation method, an exact relationship between the perturbation of structural parameters such as stiffness change and the modal properties of the tested structure is developed. An iterative solution procedure is then provided to solve for the structural updating parameters that characterise the modifications of structural parameters at element level, giving optimised solutions in the least squares sense without requiring an optimisation method. A regularization algorithm based on the Tikhonov solution incorporating the generalised cross-validation method is employed to reduce the influence of measurement errors in vibration modal data and then to produce stable and reasonable solutions for the structural updating parameters. The Canton Tower benchmark problem established by the Hong Kong Polytechnic University is employed to demonstrate the effectiveness and applicability of the proposed model updating technique. The results from the benchmark problem studies show that the proposed technique can successfully adjust the reduced finite element model of the structure using only limited number of frequencies identified from the recorded ambient vibration measurements.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.291-300
• /
• 1998

This paper demonstrates how ambient vibration measurements at a limited number of locations can be effectively utilized to estimate parameters of a finite element model of a large-scale structural system involving a large number of elements. System identification using ambient vibration measurements presents a challenge requiring the use of special identification techniques, which ran deal with very small magnitudes of ambient vibration contaminated by noise without the knowledge of input farces. In the present study, the modal parameters such as natural frequencies, damping ratios, and mode shapes of the structural system were estimated by means of appropriate system identification techniques including the random decrement method. Moreover, estimation of parameters such as the stiffness matrix of the finite element model from the system response measured by a limited number of sensors is another challenge. In this study, the system stiffness matrix was estimated by using the quadratic optimization involving the computed and measured modal strain energy of the system, with the aid of a sensitivity relationship between each element stiffness and the modal parameters established by the second order inverse modal perturbation theory. The finite element models thus identified represent the actual structural system very well, as their calculated dynamic characteristics satisfactorily matched the observed ones from the ambient vibration test performed on a large-scale structural system subjected primarily to ambient wind excitations. The dynamic models identified by this study will be used for design of an active mass damper system to be installed on this structure fer suppressing its wind vibration.

• 산업기술연구
• /
• 제22권A호
• /
• pp.29-36
• /
• 2002

A damage detection algorithm using vibration modes is applied to the ring structures and the modal behaviors of the slightly asymmetric rings are examined. Mode shape change, MSER(modal strain energy ratio) and MCR(modal curvature ratio) are investigated to identify the locations of faults or damages The above fault detection parameters are calculated and compared by the finite element analysis on rings with designed local damages. Damages are modeled as a reduced stiffness in the analysis The results show that MSER and MCR can be proper parameters to detect local damages in the ring structures.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.1997-2004
• /
• 1994

A model analysis method has been developed in the paper. The method estimates the modal parameters of multiple input-output systems, assesses their quality, and seperates structural modes form computation ones. The modal parameter extraction algorithm is the least squares method with a finite difference model relating input and output time data. The quality of the estimated system model can be assessed in narrow frequency bands by comparing the measured and model predicted responses in time domain with the aid of digital filters. Structural modes can be effectively separated from computational ones using the convergence factor which represents the pole convergence rate. The modal analysis method has been applied to simulated and experimental vibration data to evaluate its utility and limitations.

• Earthquakes and Structures
• /
• 제15권3호
• /
• pp.263-273
• /
• 2018

Operational modal analysis is being widely used in aerospace, mechanical and civil engineering. Common research fields include optimal design and rehabilitation under dynamic loads, structural health monitoring, modification and control of dynamic response and analytical model updating. In many practical cases, influence of noise contamination in the recorded data makes it difficult to identify the modal parameters accurately. In this paper, an improved frequency domain method called Enhanced Least Square Complex Frequency (eLSCF) is developed to extract modal parameters from noisy recorded data. The proposed method makes the use of pre-defined approximate mode shape vectors to refine the cross-power spectral density matrix and extract fundamental frequency for the mode of interest. The efficiency of the proposed method is illustrated using an example five story shear frame loaded by random excitation and different noise signals.