• 한국건축시공학회지
• /
• 제22권1호
• /
• pp.45-55
• /
• 2022

초 저수축 콘크리트는 콘크리트 구조물의 건조수축 균열을 극한으로 제어할 수 있기 때문에 콘크리트 구조물의 품질 및 외관 확보에 매우 효과적이다. 본 연구에서는 초 저수축 콘크리트의 상용화를 목적으로 실내실험을 통해 최적의 팽창재 및 수축저감제 투입량을 정하였고, 콘크리트 벽체 실물대부재실험을 실시하여 초 저수축 콘크리트의 수축 특성 및 균열제어 효과 등을 검토하였다. 그 결과 벽체 시험체에는 건조수축 변형이 거의 발생하지 않았고 균열도 발생하지 않음을 확인할 수 있었다.

• The Journal of the Acoustical Society of Korea
• /
• 제28권1E호
• /
• pp.9-15
• /
• 2009

In this paper, FSTL (Field Sound Transmission Loss) measured in a mock-up simulating ship cabins is studied. A mock-up is built by using 6 mm steel plate, and two identical cabins are made where 25 mm or 50 mm sandwich panel is used to construct wall and ceiling inside the steel structure. Various wall panels and ceilings are tested, where effects of wall and ceiling panel thickness, and presence of a unit toilet on FSTL are investigated. It is found that the effect of unit toilet on FSTL is at most 1 dB. From the comparison of FSTL for panels of the same thickness of 50 mm, it is observed that panel having inside air cavity of 10 mm shows higher STL than that of the panel without air cavity. Comparison of FSTL for panels of 50 mm and 25 mm thickness shows that dependency on surface density predicted by mass law is not observed. The sandwich panels act as a mass-spring system, which shows a resonant mode that cannot be explained by the mass law. It is also found that STL from laboratory test is higher than FSTL by 5- 10 dB, which can be explained by flanking structure-borne noise transmission path such as ceiling, floor and corridor-facing wall.

• 대한건축학회논문집:구조계
• /
• 제34권3호
• /
• pp.43-52
• /
• 2018

This study is conducted to evaluate the performance of ceramic panels and painting materials for humidity control which are developed in non-plastic room temperature hardening structure as part of a project to improve a residential environment for the low-income class, rather than the performance of high-priced humidity control materials that are produced with the existing plasticity processing. The testing methods included the measurements of absorption & desoprtion of humidity per material; Mock-up Testing; an evaluation method of comparing the absorption & desoprtion performances of Ecocarat, ceramic panels and painting materials through Living Lab. According to the measurements of absorption & desoprtion per material, ceramic panels, E panel, and ceramic painting material showed 73.3g/m2, 96.6g/m2, and 111.1g/m2, respectively. That is, the performance of humidity control of each material was found to be good in the order of: Ceramic Paint > E panel > Ceramic Panel. According to performance evaluation testing with Mock-up test and Living Lab, Ceramic Paint, Ecocarat, and Ceramic Panels showed better absorption & desoprtion performances in the order.

• Elastomers and Composites
• /
• 제35권2호
• /
• pp.138-148
• /
• 2000

EPDM 발포체의 정적/동적 특성을 측정하여 재료 특성과 진동 특성과의 연관성을 알아보고 이로부터 충격음 저감재로서의 적용 가능성을 검토하였다. 정적/동적 특성은 material test system (MTS)를 사용하여 시편의 형상, 두께, 초기하중, 발포도 등에 따라 정적 탄성계수, 동적 탄성계수, 전달율의 변화를 조사하였다. 정적 탄성계수와 동적 탄성계수의 경우, 형상이 단순하고 두께가 얇을수록 큰 값을 나타냈고, 전달율과 동적 탄성계수는 상호 비례 관계에 있음을 확인할 수 있었다. 특징적으로 동적 탄성계수가 증가하면, 전달율의 특성 피크치는 같은 주파수 영역에서의 증가 혹은 고주파수 영역으로의 전이의 형태로 일어나게 되는 것을 알 수 있었다. 실험실적 모사 시험장치를 통해 충격에 따른 주파수별 진동 속도측정과 유한 요소 해석 모델을 사용하여 mode shape에 의한 충격 해석 결과를 알아보았는데, EPDM 발포체를 사용함으로써 2.5-3.5배의 진동 속도 저감이 이루어짐을 알 수 있었고, mode shape의 경우 몰타르와 콘크리트만으로 구성된 구조물에 비해 진동 충격에 대한 변위가 급감함으로써 충격음 저감재로서의 EPDM 발포체의 적용 가능성은 상당히 높은 것을 확인할 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.361-364
• /
• 2005

This study reports the properties of high early strength of concrete using PC admixture. To apply these data to construction site, we did the lab tests and mock-up test. The target of this study is to accomplish early strength of concrete(5 MPa/18 hr), and we tested by the different factors, such as the type of admixtures, curing temperature, the amount of binder, etc. Through the test of concrete using the different type of admixture, PC type was more excellent than PNS type admixture. According to these tests, we concluded that we can apply this type of PC Admixture to the civil & construction site, and we can reduce the term of works and finally we can accomplish the economical construction.

• 한국군사과학기술학회지
• /
• 제21권1호
• /
• pp.69-73
• /
• 2018

Korean-peacekeeper's transparent armors in Iraq showed delamination, cracking and clouding a decade ago. And there were also similar deterioration recurrences in KLTV during the operational test a few years ago. Also, the differences between operational capability & lab Bullet-proof test condition, and insufficiency of military protection spec resulted in incomplete bullet-proof results. Moreover, although so many ground weapon systems have been developed, there were not secure test & evaluation codes to verify transparent armoured glasses equal to advanced-overseas products. So in this study, first, environmental test codes were established that all tests should be carried out as the application of only one specimen with newly adopted thermal shock test instead of completing each test with different one. Second, protection standards were integrated through the analysis of global developed country's specifications and reinforced as adding to the real mock-up condition if vehicle's glasses are smaller than standard specimen. Hereby, by applying to test-codes which including actual operational & vehicular conditions, the gap between development test and operational environment was minimized.

• Nuclear Engineering and Technology
• /
• 제47권6호
• /
• pp.776-790
• /
• 2015

Background: The advanced spent fuel conditioning process facility (ACPF) of the irradiated materials examination facility (IMEF) at the Korea Atomic Energy Research Institute (KAERI) has been renovated to implement a lab scale electrolytic reduction process for pyroprocessing. The interior and exterior structures of the ACPF hot cell have been modified under the current renovation project for the experimentation of the electrolytic reduction process using spent nuclear fuel. The most important aspect of this renovation was the installation of the argon compartment within the hot cell. Method: For the design and system implementation of the argon compartment system, a full-scale mock-up test and a three-dimensional (3D) simulation test were conducted in advance. The remodeling and repairing of the process cell (M8a), the maintenance cell (M8b), the isolation room, and their utilities were also planned through this simulation to accommodate the designed argon compartment system. Results and conclusion: Based on the considered refurbishment workflow, previous equipment in the M8 cell, including vessels and pipes, were removed and disposed of successfully after a zoning smear survey and decontamination, and new equipment with advanced functions and specifications were installed in the hot cell. Finally, the operating area and isolation room were also refurbished to meet the requirements of the improved hot cell facility.