• 구강회복응용과학지
• /
• 제30권3호
• /
• pp.259-264
• /
• 2014

역행성 임플란트 근단병소 주위염은 임상증상을 동반한 근단부의 방사선 투과성 병소로 정의되며 임플란트 식립부위 또는 인접한 치아의 잔존하고 있는 감염에서 유래한 세균감염, 골 삭제시의 열 발생 등의 다양한 원인에 의해 야기될 수 있고, 다양한 치료방법으로 임플란트를 제거하지 않고 유지할 수 있는 증례들이 보고되고 있다. 본 증례에서는 근관 치료 실패로 발치한 상악 우측 제2소구치 부위에 식립한 임플란트에서 발생한 역행성 임플란트 근단병소 주위염을 표면의 detoxification과 차폐막과 골이식재를 동반한 골유도재생술로 해결하여 기능을 회복하였으며, 7년간 장기적으로 안정적으로 유지되고 있는 증례에 대해 보고하고자 한다.

• 마이크로전자및패키징학회지
• /
• 제11권4호
• /
• pp.37-41
• /
• 2004

이동 통신 기기의 광대역화에 따라 기존의 인쇄 회로 기판에 비해 양호한 전기적 특성과 수동형 부품을 내장할 수 있는 LTCC(Low Temperature Co-fired Ceramic)에 대한 많은 연구 개발이 진행되고 있으나 불 균일한 수축으로 인해 적용에 한계를 보여 왔다. 본 연구에서는 짧은 시간내에 온도를 균일하게 올릴 수 있는 혼합 가열 방식을 개발하여 하부에서부터 시편의 얇은 층이 순차적으로 소결 되도록 하는 일 방향 소결의 조건을 제공하여 시편 상부 표면의 배선 형상이 종래의 전기로 가열보다 안정적으로 형성되는 결과를 얻었다. 기판의 소결 특성, 배선의 전기적 특성, 그리고 배선의 기계적 특성 등을 비교한 결과, 기판의 소형화와 배선의 고밀도화에 전기로 가열 보다 혼합 가열이 적용 가능성이 높음을 알 수 있었다.

• 한국대기환경학회지
• /
• 제33권2호
• /
• pp.139-158
• /
• 2017

CMAQ (Community Multiscale Air Quality Model) simulations were carried out to estimate the potential range of contributions on surface $PM_{2.5}$ concentrations over the Seoul Metropolitan Area (SMA) with the gaseous precursors and Primary Particulate Matters(PPM) available from a recent national emissions inventory. In detail, on top of a base simulation utilizing the 2013 Clean Air Policy Supporting System (CAPSS) emission inventory, a set of Brute Force Method (BFM) simulations after reducing anthropogenic $NO_x$, $SO_2$, $NH_3$, VOCs, and PPM emissions released from area, mobile, and point sources in SMA by 50% were performed in turn. Modeling results show that zero-out contributions(ZOC) of $NH_3$ and PPM emissions from SMA are as high as $4{\sim}5{\mu}g/m^3$ over the region during the modeling period. On the contrary, ZOC of local $NO_x$ and $SO_2$ emissions to SMA $PM_{2.5}$ are less than $1{\mu}g/m^3$. Moreover, model analyses indicate that a wintertime $NO_x$ reduction at least up to 50% increases SMA $PM_{2.5}$ concentrations, probably due to increased HNO3 formation and conversion to aerosols under more abundant ozone and radical conditions after the $NO_x$ reduction. However, a nation-wide $NO_x$ reduction decreased SMA $PM_{2.5}$ concentrations even during winter, which implies that nation-wide reductions would be more effective to curtail SMA $PM_{2.5}$ concentrations than localized efforts.

• 한국식품영양학회지
• /
• 제26권3호
• /
• pp.547-552
• /
• 2013

황백 껍질은 황벽나무(Phellodendron amurense)의 건조된 수피로부터 얻어진다. 이 수피는 한국의 전통 한약제로서, 설사, 황달, 무릎과 발의 통증, 요도관 및 피부 감염증에 폭넓게 사용되어 왔다. 본 연구는 황벽나무의 메탄올 추출액으로부터 항균성 화합물 분리를 위해 CPC 방법으로 효과적으로 수행하였다. 두 용매의 CPC 최적조성은 n-butanol:acetic acid:water(4:1:5 v/v/v)이었다. 이동상의 유속은 1,000 rpm 회전력에서 상승법으로 분당 3 $m{\ell}$ 속도로 전개시켰다. CPC에서 분리된 분획분은 prep-HPLC로 정제하였다. 분리된 palmatine은 $^1H$, $^{13}C$-NMR, ESI-MS 데이터 분석으로 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.76-76
• /
• 2011

Polymer-fullerene based bulk heterojunction (BHJ) solar cells can be fabricated in large area using low-cost roll-to-roll manufacturing methods. However, because of the low mobility of the BHJ materials, there is competition between the sweep-out of the photogenerated carriers by the built-in potential and recombination within the thin BHJ film [12-15]. Useful film thicknesses are limited by recombination. Thus, there is a need to increase the absorption by the BHJ film without increasing film thickness. Metal nanoparticles exhibit localized surface plasmon resonances (LSPR) which couple strongly to the incident light. In addition, relatively large metallic nanoparticles can reflect and scatter the light and thereby increase the optical path length within the BHJ film. Thus, the addition of metal nanoparticles into BHJ films offers the possibility of enhanced absorption and correspondingly enhanced photo-generation of mobile carriers. In this work, we have demonstrated several positive effects of shape controlled Au and Ag nanoparticles in organic P3HT/PC70BM, PCDTBT/PC70BM, Si-PCPDTBT/PC70BM BHJ-based PV devices. The use of an optimized concentration of Au and Ag nanomaterials in the BHJ film increases Jsc, FF, and the IPCE. These improvements result from a combination of enhanced light absorption caused by the light scattering of the nanomaterials in an active layer. Some of the metals induce the plasmon light concentration at specific wavelength. Moreover, improved charge transport results in low series resistance.

• 공업화학
• /
• 제27권5호
• /
• pp.455-466
• /
• 2016

유기 발광 다이오드(OLED)는 학문 및 산업분야에서 많은 관심을 받고 있다. OLED는 이미 휴대폰과 TV분야에서 상업화에 성공하고 있으며, 조명분야에서는 기존에 사용되어왔던 백열등, 형광등과는 다르게 면발광, 대면적, 초경량, 초박형, 유연성의 특징은 물론 낮은 에너지 사용 등의 차별성을 가지고 있기 때문에 최근 많은 관심을 받고 있다. 본 논문에서는 white organic light-emitting diode (WOLED)에 적용되는 대표적인 형광 및 인광 발광 재료들을 소개한다. 이렇게 선행 연구된 물질들을 이해하고 체계적으로 분류하는 것은 앞으로 새로운 발광 재료를 연구, 개발하는데 큰 도움을 줄 수 있을 것으로 기대된다.

• 한국전자파학회논문지
• /
• 제26권1호
• /
• pp.16-23
• /
• 2015

본 논문에서는 WCDMA2100 이동통신망을 사용하는 밴드형 wearable device에 적합한 bent 마이크로스트립 패치 안테나와 이를 적용하기 위한 RF configuration을 제안하였다. 제안된 안테나는 WCDMA2100 송수신 주파수 대역을 분리한 RF configuration을 사용하여 WCDMA 송신대역에서만 동작하도록 설계되었고, 후면의 도체(ground)로 인해 인체의 영향을 적게 받는다. 제안된 안테나는 flat 및 bent할 경우 모두 최대 이득은 5.3 dBi 이상, -6 dB 반사손실 대역폭은 20 MHz 이상을 가지고 전자파 인체 흡수율 시뮬레이션 $SAR_{1g}$ 0.7 [W/kg] 이하를 갖는다. 제안된 안테나는 사람의 손목이나 팔에 착용하는 밴드형 wearable device에 적합하게 사용될 수 있다.

• 한국운동역학회지
• /
• 제20권2호
• /
• pp.221-230
• /
• 2010

The purpose of this study was to analyze biomechanical factors of trail running shoes applied to korean shoe-lasts. 10 healthy male subjects with an average age of 37.2 years(SD=8.28), weight of 69.6 kg(SD=10.56) and a height of 171 cm(SD=4.93) were recruited for this study. Ten males walked on a treadmill wearing four different shoes. Foot pressure data was collected using a Pedar-X mobile system(Novel Gmbh., Germany) operating at the 1000 Hz. Surface EMG signals for tibialis anterior, gastrocnemius, vastus lateralis and biceps femoris were acquired at 1000 Hz using Noraxon TeleMyo DTS system(Noraxon Inc., USA). Foot pressure and leg muscle fatigue were measured and calculated during walking. The results are as follows: After walking 60 minutes, Type A showed a lower MPF. MPF values were significantly different from each muscle(p<.05). Therefore, Type A shoe might decrease muscle fatigue in the legs while walking. In addition, Type It showed that Type A shoe has the highest contact area and the lowest maximum pressure. As a result of the analysis, Trail running shoes will use a new design to reduce muscle fatigue and are expected to increase comfort and fitting.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.631-631
• /
• 2013

Battery has major drawbacks including its size and life expectancy, and environmental problem. As an alternative, energy harvesting is emerging as a potential solution to replace battery along with more energy-efficient IT devices. The idea of harnessing energy from our living environment is sustainable, semi-permanent, and eco-friendly. Also, unlike battery, energy harvester does not require much space to store energy. Therefore, energy harvesting can provide a better source of power for small, portable, and wireless devices. Among various ways of harvesting energy from our surroundings, triboelectricity is chosen due to its potential to be miniaturized, and efficient. Triboelectric effect occurs as two different materials with different polarity of charge separation come into contact through friction, and then become separated so that electric potential difference is achieved. In this research, such characteristic of triboelectricity is used as a way to convert ambient mechanical energy into electric energy.Series of recent researches have shown promising results that the triboelectric energy harvester can be simple and cost effective. However, sufficient electricity level required to operate mobile devices has not yet been achieved.In this research, our group focuses on the design and optimization of triboelectric energy harvesting device to enhance its output. By using maskless lithography to pattern Kapton film and silicon substrate, which is used as a mold for PDMS thin layer, and sputtering metal electrodes on each side, we fabricate and demonstrate different designs of triboelectric energy harvester that utilizes the contact electrification between a polymer thin film and a metal thin foil. In order to achieve optimized result, the output voltage and current are measured under diverse conditions, which include different surface structure and pattern, material, and the gap between layers.

• 한국분무공학회지
• /
• 제21권3호
• /
• pp.130-136
• /
• 2016

NOx and PM are important air pollutants as vehicle management policy aspect. Medium-duty truck is the main source of the pollutants although the vehicle market share is only 3.5%. National emission portion of NOx and PM form the mobile sourece are 14% and 16% respectively. In this study it was investigated that characteristics of air pollutants emission on medium duty truck equipped with EGR and SCR system. Vehicle's test reflected driving cycle on the chassis dynamometer, and applied test cycle was WHVC(World Harmonized Vehicle Cycle) mode. The test cycle include three segments, represent urban, rural and motorway driving. Based on the test results NOx, PM, HC were less emitted form SCR vehicle than EGR vehicle. And CO was less emitted form EGR vehicle than SCR vehicle due to CO oxidation reaction on DPF surface. And most air pollutants reduced as average vehicle speed increased. Pollutants were less emitted on motorway section than urban and rural sections. But highly NOx emission on motorway section was verified according to increased EGR ratio on fast vehicle speed. HC and CO additional emission was identified as 68%, 58% respectively during SCR vehicle's cold engine start emission test. NOx additional emission was detected by 24% on SCR vehicle's condition of engine cold start while not detected on vehicle equipped with EGR. SCR vehicle's additional NOx emission was derived from low reaction temperature during engine cold start condition. medium-duty truck emission characteristics were investigated in this study and expected to used to improve air pollutants management policy of medium-duty truck equipped with SCR & EGR.