• Korean Journal of Materials Research
• /
• v.8 no.3
• /
• pp.274-279
• /
• 1998

Optimum Cu and Mn contents in 0.05wt%C-Cu bearing hot rolled steel sheets were investigated by vickers hardness measurement, tensile test and transmission electron microscopy. It was determined that the optimum Cu and Mn contents were 1.2wt% and 0.75-0.85wt% respectively. It was confirmed by TEM observation that the coarse recipitates were fcc $\varepsilon$-Cu in 0.05%C-1.2%Cu-0.75%Mn-O.O4%Nb steel sheets. The Cu-bearing steel sheets having 780MPa of tensile strength could be fabricated by 10% pre-strain and aging treatment at $550^{\circ}C$ for 30min.

• Proceedings of the KIEE Conference
• /
• 2008.05a
• /
• pp.199-200
• /
• 2008

ZnO을 주원료로 하고 첨가제로 $Bi_2O_3$, $Sb_2O_3$, $Nd_2O_3$, CoO, $Cr_2O_3$, $MnO_2$, NiO를 고정한 후 $Y_2O_3$ 첨가량에 바리스터의 전기적 특성을 검토하였다. $Y_2O_3$ 첨가량이 증가할 수록 바리스터 전압이 직선적으로 증가함을 확인할 수 있으며 결정립계에 존재하는 스핀넬상에 $Y_2O_3$가 이차상으로 존재함을 확인 할 수 있었다. $Y_2O_3$ 첨가에 따라 ZnO 결정입자 성장을 방해하여 바리스터 전압을 증가시키는 반면 결정립의 크기를 불균일하게 하여 유전율을 감소시키고 유전손실은 증가함을 확인하였다. 본 연구 결과 $Y_2O_3$ 첨가로 바리스터 전압은 350 V/mm이상을 얻을 수 있으며 누설전류를 $1{\mu}A$이하로 하는 조성을 얻을 수 있었으며 소형 바리스터 제작이 가능함을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.47-53
• /
• 2003

자발착화연소법과 분무열분해법을 동시에 적용한 초음파분무연소법을 이용하여 40~50nm 크기를 갖는 결정성 ZnO 분말을 합성하였다. 또한 바리스터로의 응용을 위해 Bi, Sb, Co, Mn을 초기출발원료인 Zn-nitrate에 첨가하여 복합조성의 ZnO계 바리스터 분말을 합성하였다. 합성된 바리스터의 분말을 성형 및 소결하여 전기적 특성을 관찰한 결과 Co를 첨가한 분말보다 Mn을 첨가한 분말에서 우수한 전기적 특성을 나타내었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.318-319
• /
• 2005

본 연구에서는 $LiCoO_2/LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$ 혼합 정극활물질로 사용하여 전극을 제작하고 성능을 평가하였다. $LiCoO_2/LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$와 $LiCoO_2$의 혼합비에 따른 충방전 거동 및 임피던스 변화를 측정하였다. 각 조성에서의 초기용량은 160 ~ 170 mAh/g 정도였으며, $LiNi_{1/3}Mn_{1/3}Co_{1/3}O_2$의 첨가 비율이 증가함에 따라 비용량이 증가하였으나 고율에서의 방전용량은 낮았다.

• Journal of the Korean Ceramic Society
• /
• v.34 no.3
• /
• pp.289-295
• /
• 1997

Effect of ceramic processing was investigated on the microstructure and electronic properties of low loss Mn-Zn ferrite. Addition of CaO and SiO2 to calcined powder rather than to raw materials mixtured resulted in finer-grained microstructure. Higher oxygen pressure during sintering caused microstructural inhomogeneity and the increase in power loss and disaccommodation factor. Relatively low power loss was found for sintering up to 130$0^{\circ}C$ from powders calcined at high temperature and milled shortly. It was caused by slow densification rate and normal grain growth up to 130$0^{\circ}C$. Calcination at low temperature and prolonged milling enhanced den-sification, which gave a fine grained microstructure and low powder loss at sintering temperture below 120$0^{\circ}C$. Sintering temperature above 125$0^{\circ}C$, however, showed abnormal grain growth.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1998.05a
• /
• pp.68-69
• /
• 1998

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.29.1-29.1
• /
• 2000

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.5
• /
• pp.362-366
• /
• 2000

$Li_{0.44}MnO_2$cathode material has high reversibility during lithium insertion processes and is not easily damaged through over-charging or over-discharging. $Mn_2O_3$is often present as an impurity phase, and reduce the electrochemical capacity of electrode because this phase is electrochemically inert. Adding of excess NaOH reduced the $Mn_2O_3$to the content under undetectable by X-ray diffraction. Because the capacity can be increased in the cathode materials with larger unit cell, some of the manganese was replaced with titanium having larger ion size, and powders with the formula $Li_{0.44}T_{iy}Mn_{1-y}O_2$(where y = 0.11, 0.22, 0.33, 0.44, and 0.55) was synthesized and characterized. A maximum reversible capacity of 150 mAh/g was obtained for $Li/P(EO)_8$LiTFSI/$Li_{0.44}Ti_{0.22}Mn_{0.78}O_2$cells in electrochemical potential spectroscopy (ECPS) experiments. Cells with the titanium-doped manganese oxides exhibited a fade rate of 0.12 % or less per cycle.

• Journal of the Korean Ceramic Society
• /
• v.41 no.9
• /
• pp.709-714
• /
• 2004

The additive of low temperature sintering in Mn-doped PMN-PZT known as high piezoelectric materials was studied in this experiment. B$_2$O$_3$ was used for the additive of low temperature sintering. The effects of sintering temperature in dielectric, and piezoelectric properties were investigated with the amounts of B$_2$O$_3$. Sintered density was increased in comparison with no addition and under 2wt％ B$_2$O$_3$ and lower sintering temperature than 100$0^{\circ}C$. Therefore, in the low sintering temperature, the densification was improved by the addition of the B$_2$O$_3$. However, the sintering density was lower than that of the main composition in the case of the sintered at over 10$50^{\circ}C$. Dielectric constant with the addition of B$_2$O$_3$ was evaluated. The dielectric constant was 1000 2 wt％ of B$_2$O$_3$ and sintered at 100$0^{\circ}C$. Under 2wt％ of B$_2$O$_3$, the electromechanical coupling factor and the piezoelectric constant were not so much decreased. The electromechanical coupling factor and the piezoelectric constant were 50％ and 300(${\times}$10$^{-12}$ C/N) respectively. The mechanical quality factor was increased with B$_2$O$_3$. The mechanical quality factor was 1700 at 0.5wt％ B$_2$O$_3$ and sintered at 110$0^{\circ}C$. Dielectric loss was less than 0.5％ regardless of the amount of B$_2$O$_3$.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.93-96
• /
• 2000

In this study, we investigated the electromagnetic properties of Mn-Zn ferrite doped with rare earth oxide (Dy$_2$O$_3$, Er$_2$O$_3$). The main composition is 52mo1% $\alpha$-Fe$_2$O$_3$, 25mo1% Mn$_3$O$_4$23mo1% ZnO and doped with them(0.05wt%~0.25wt%, step:0.05wt%). An experimental process has advanced by conventional ferrimagnetism manufacturing that was prepared by standard ceramic techniques. The XRD pattern of all doped sample were observed spinel and secondary phase. The density of sample were measured nearly constant value. As increased the additive, resistivity, initial permeability and real component of the series complex permeability increased with setting limits each other. In case of Mn-Zn ferrite excess doped with them, resistivity, initial permeability and real component of the series complex permeability decreased and magnetic loss increased in proportion to increasing the additive.