• 한국정밀공학회지
• /
• 제28권6호
• /
• pp.751-757
• /
• 2011

Subminiature devices such as Lab-on-a-chip and p-TAS(Micro Total Analysis System) have been intensively studied in biotechnology and chemistry, In many cases, a micromixer was widely used to mix different solutions for synthesizing novel materials. However, in microfluidic system, there is generally a laminar flow under very small Reynolds number so it is difficult to mix each solution perfectly. To settle this problem, we propose a new mixing mechanism which generates a horizontal and vertical multi-mixing (HVM) flow for effective mixing within a short mixing section. We evaluated the proposed mechanism using CFD analysis, and the results showed that the HVM mechanism had a relative high-effectiveness comparing to the existing methods.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3128-3133
• /
• 2007

The mixing method of water and chemicals is significant in a small-scale water supply system because drinking water should be supplied with a certain quantity of remaining chemicals maintained. In the present study, the concentration distribution and the mixing index were obtained from four models, which were to find out the optimal mixing method of water and chemicals. The two models brought the good mixing effects out of the four, one for providing chemicals from the center of water supply pipe and the other for setting up the semicircle block at the downstream of the chemicals-providing pipe. As a result, the mixing effect was found out to be increased due to the diffusion and the disturbance of flows. In conclusion, these results are expected to contribute to designing the optimal mixing system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1516-1521
• /
• 2004

Mixing in Y-channel micro mixer is analyzed through computational fluid dynamics. In the case of passive mixing, we investigate the effect of geometric parameters on the mixing efficiency, such as shape of throttling geometry and angle between two inlets. Mixing performance improves as two fluids join not just horizontally but both vertically and horizontally, and it also improves when channel follows throttling shapes. A numerical results substantiate the highly efficient mixing performance. It is highly beneficial to fabrication process since the proposed throttling geometry is simple, but allows high mixing ratio.

• 대한기계학회논문집B
• /
• 제29권12호
• /
• pp.1369-1376
• /
• 2005

Effective mixing gives strong advantageous impact on microfluidic applications since mixing is in general very slow process motivated by molecular diffusion transport only on the micro-scale. In this work, the mixing characteristics are analyzed in a Y-channel micromixer with obstacles. For the through analysis, our laboratory in-house unstructured grid CFD code is validated through solving a concentration transport in a uniform microchannel. The solutions well correspond to both exact solutions and those from MemCFD. Mixing in a Y-channel micromixer with obstacles is numerically investigated by the in-house code to search the optimal radius and layout of obstacles. From the simulations, the mixing efficiency appears to be proportional to the magnitude of the formation of lateral velocity component. It is also shown that the asymmetric layout and radius enlargement of obstacles greatly improves mixing efficiency.

• 대한기계학회논문집B
• /
• 제29권12호
• /
• pp.1307-1312
• /
• 2005

Turbulent in-situ mixing process is a new material process technology to get dispersed phase in nanometer size by controlling reaction of liquid/liquid, liquid/solid and liquid/gas, flow and solidification speed simultaneously. In this study mixing, the key technology to this synthesis method will be studied by computational fluid dynamics. For the simulation of mixing of liquid metal, static mixers will be investigated. Two inlets for different liquid metal meet and merge like 'Y' shape tube. The tube has various shapes such as straight and curved. Also, the radius of curve will be varied. The performance of mixer will be evaluated with quantitative analysis with coefficient of variance of mass fraction. Also, detailed plots of intersection will be presented to understand effect of mixer shape on mixing.

• 한국전산유체공학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

The mixing of water and chemicals is an important process in the water purification plant. In this paper, we compare PDM(pump diffusion mixer) and hydraulic mixer at the basin in the mixing process. The proper flow rates are predicted and compared in both mixers using CFD technique. As a result, the flow rate of purifier chemical liquid should be 5% of that of water for the optimal performance of mixing process. The characteristics of the two mixing methods are compared with each other for strong and weak points on the operation of the purification system, discussed in the view point of CFD simulations.

• Journal of Mechanical Science and Technology
• /
• 제17권9호
• /
• pp.1380-1387
• /
• 2003

When a cold HPSI (High pressure Safety Injection) fluid associated with an overcooling transient, such as SGTR (Steam Generator Tube Rupture), MSLB (Main Steam Line Break) etc., enters the cold legs of a stagnated primary coolant loop, thermal stratification phenomena will arise due to incomplete mixing. If the stratified flow enters the downcomer of the reactor pressure vessel, severe thermal stresses are created in a radiation embrittled vessel wall by local overcooling. As general thermal-hydraulic system analysis codes cannot properly predict the thermal stratification phenomena, RG 1.154 requires that a detailed thermal-mixing analysis of PTS (pressurized Thermal Shock) evaluation be performed. Also. previous PTS studies have assumed that the thermal stratification phenomena generated in the stagnated loop side of a partially stagnated primary coolant loop are neutralized in the vessel downcomer by the strong flow from the unstagnated loop. On the basis of these reasons, this paper focuses on the development of a 3-dimensional thermal-mixing analysis model using PHOENICS code which can be applied to both partial and total loop stagnated cases. In addition, this paper verifies the fact that, for partial loop stagnated cases, the cold plume generated in the vessel downcomer due to the thermal stratification phenomena of the stagnated loop is almost neutralized by the strong flow of the unstagnated loop but is not fully eliminated.

• 대한기계학회논문집B
• /
• 제31권8호
• /
• pp.711-717
• /
• 2007

Shape optimization of a staggered herringbone groove micromixer using three-dimensional Navier-Stokes analysis has been carried using Kriging model. The analysis of the degree of mixing is performed by the calculation of spatial data statistics. The calculation of the variance of the mass fraction at various nodes on a plane in the channel is used to quantify mixing. A numerical optimization technique with Kriging model is applied to optimize the shape of the grooves on a single wall of the channel. Three design variables, namely, the ratio of groove width to groove pitch, the ratio of the groove depth to channel height ratio and the angle of the groove, are selected for optimization. A mixing index is used as the objective function. The results of the optimization show that the mixing is very sensitive to the shape of the groove which can be used in controlling mixing in microdevices.

• 한국식품조리과학회지
• /
• 제25권2호
• /
• pp.260-265
• /
• 2009

The influence of mixing ratio of 25 commercial rice varieties was evaluated by DNA analysis and Toyo value palatability. No relationship was evident between rice palatability and various grain quality properties, or between palatability and mixing ratio. A positive relationship was evident between palatability and texture and between palatability and chalky rice ratio. A negative relationship was evident between mixing ratio and amylose content.

• Nuclear Engineering and Technology
• /
• 제33권3호
• /
• pp.327-338
• /
• 2001

A computational fluid dynamics (CFD) analysis was performed to propose the optimum design of flow mixing vane on the space grid in a PWR fuel assembly. The flow mixing vanes considered in this study for optimum design are swirl-vane and twisted-vane. A single subchannel of one grid span was modeled using flow symmetry to minimize the computational effort. The CFD predictions are in good agreement with the experimental results for the split- vane, which shows the applicability of the CFD method. The mixing effect by swirling flow and crossflow, and the pressure drop were estimated and compared for the various vane angles. The optimum vane angle is proposed to be 40。 and 35。 from the direction of axial flow for the swirl-vane and the twisted-vane, respectively.